-
Dynalink RTA1335 - page 1
Quick Setup Guide R T A1335 ADSL 2+ 4 -Port Modem Router ...
-
Dynalink RTA1335 - page 2
Impor tant This Guide is intended to get you started quickly . W e have made the factory default setting of this router suitable for New Zealand 1 . All you need is to follow thr ough the steps we describe here. This Guide should be read in conjunction with the RTA1335 ADSL Router User’s Manual 2 . It is pro vided as a PDF file on this CD. T o vi ...
-
Dynalink RTA1335 - page 3
Default Configuration for New Z ealand This Router is shipped with the following factory default settings. Router IP address 192.168.1.1 Subnet mask 255.255.255.0 VPI 0 VCI 1 00 Connect mode PPPoA V C-MUX NA T enabled DSL line mode G.DMT WAN I P dynamic DHCP enabled DNS relay on UPnP IGD enabled Firewall: Incoming requests blocked Outgoing traffic ...
-
Dynalink RTA1335 - page 4
Connection of this router to computers is via Ethernet, independent of the Operating System. There is no driver to load. This router comes with a built-in 4-port network switch. Up to 4 computers can be connected to the router directly. If you require connections for more computers, purchase another network hub and connect it to the router to provi ...
-
Dynalink RTA1335 - page 5
Getting On-line Before you start, the DSL & Ethernet lights on the router must be on. Refer to Section 10 – Troubleshooting of this Guide to resolve any issues. STEP 1 GO TO THE ‘CONNECT TO INTERNET’ PAGE Start your web browser . Enter the default address http://192.168.1.1. T ype admin for both User name and Password. See Q1 in Section 1 ...
-
Dynalink RTA1335 - page 6
Once connected the screen changes to display the on-line time. The PPP light on the front panel of the router will come on, indicating that you ar e online. Click Disconnect only if you wish to disconnect manually. Y our Internet account user name & password will be saved automatically . If previously the computer had a modem for Internet conne ...
-
Dynalink RTA1335 - page 7
6 ADSL 2+ 4 -Port Modem Router Quick Set-up Guide PPPoE Caution - Only follow this section if your ISP advises explicitly the service is PPPoE. If you hav e followed the pr ocedure below by mistake, r eset router to factor y default will restore r outer to the standard New Z ealand setting. From the Quick Start menu click on Quick Setup to configur ...
-
Dynalink RTA1335 - page 8
6. Now follow Step 2 of Section 5 – Getting On-line. The screen will show the changes made: pppoe_0_100 has replaced the default pppoa_0_100. Some adv anced functions of your r outer Firewall, port forwarding, DMZ & traffic r estrictions By default a firewall is actively blocking incoming r equests including Ping from the Internet to your pri ...
-
Dynalink RTA1335 - page 9
ADSL 2+ 4 -Port Modem Router Quick Set-up Guide a public IP directly from the ISP . This arrangement is suitable for certain advanced applications that require the device behind to r eceive a public WAN I P . Caution: This mode of operation assumes firewall security will be provided by another device on your LAN. T o set up I P extension, go to the ...
-
Dynalink RTA1335 - page 10
8 The new configuration is displayed. Click Apply to confirm the changes. The router will restart itself to activate the new setting. Y ou will notice all NA T or fir ewall settings disappear from the Adv anced menu hereafter . Now follow S tep 2 of Section 5 – Getting On-line. Quality of Service (QoS) The router allows prioritising of upstr eam ...
-
Dynalink RTA1335 - page 11
ADSL 2+ 4 -Port Modem Router Quick Set-up Guide of your router and network. Use the built in access control list to r estrict access to only authorised Internet hosts. Enable IP extension (bridging) without firewall protection. If the router oper ating in this mode is connected to a computer , to the minimum have a “personal firewall” (software ...
-
Dynalink RTA1335 - page 12
T roubleshooting Q1. Cannot open the router control panel fr om my browser . 1. Check that the router’ s ETHE R N ET light is on. Check that the ETHE R N ET cable is firmly plugged in. 2. Perform a PING test . In Windows XP or 2000, click Start-Run. Enter cmd then OK. (In pre-2000 Windows v ersions enter command instead). T ype ping 192.168.1.1 t ...
-
Dynalink RTA1335 - page 13
ADSL 2+ 4 -Port Modem Router Quick Set-up Guide • If there is no designated ADSL jackpoint, any jackpoints may be used. Connect the router directly into a jackpoint, or thr ough the port marked MODE M on a filter . 2. If the DSL light is on, but the PPP light is off, check that: • The Internet account User Name & Password ar e correctly ent ...
-
Dynalink RTA1335 - page 14
Q5. The r outer’ s IP and/or administrativ e password hav e been modified. But the details have now been for gotten. Y ou can restore the router to factory default by pushing a pin into the hidden reset button located next to the pow er on/off button at the back of the router . Push and hold for 5 seconds then release to reset r outer . Q6. I nee ...
-
Dynalink RTA1335 - page 15
NZ-RTA1335QG-01 Dynalink warrants this product against defects in materials and workmanship for a period of twelve months fr om the original date of purchase. We will, at our discretion, repair or r eplace the faulty unit, free of charge, pr ovided it is returned to us with proof of purchase fr om an authorised dealer within the warranty period. Re ...
¿Tienes una pregunta acerca de Dynalink RTA1335?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Dynalink RTA1335, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Dynalink RTA1335 probablemente compartirá una forma de solucionarlo.