-
Digital Media 900TL - page 1
EK–DTMAU–IN. A01 DECmau 900TL INST ALLA TION The DECmau 900TL is a T oken Ring Multistation Access Unit (MAU). As a member of Digital’s T oken Ring product family , it operates in a DEChub 900 MultiSwitch, or a single-slot hub (DEChub ONE MAU 900TL). The MAU connects up to eight stations using 100-ohm shielded or unshielded cable with RJ45 co ...
-
Digital Media 900TL - page 2
FCC NOTICE – Class A Computing Device: This equipment generates, uses, and may emit radio frequency energy . The equipment has been type tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such radio frequency interfere ...
-
Digital Media 900TL - page 3
PK–02586–IL 1 ) Power LED. Lights when the MAU has power . 2 ) Module OK LED. Lights when the MAU passes its self-test. If the MAU fails its self-test, the OK LED is off. 3 ) Ring A/B LEDs. In a hub, either the A LED or the B LED is on to show the ring. In a standalone MAU, both Ring LEDs are always off. 4 ) Speed LEDs. Either the 16 LED or the ...
-
Digital Media 900TL - page 4
Note: The rear panel shown here is used only when the MAU is in a single-slot hub configuration. 1 ) Ring In LED. Lights with a Ring In connection. 2 ) Ring Out LED. Lights with a Ring Out connection. 3) Power Connector . Provides power connection for the MAU. 4 ) Ring In Connector . Connects Ring In to the Ring Out connector of a MAU or repeater . ...
-
Digital Media 900TL - page 5
a. Loosen the screw on the single-slot hub until it disengages. b. With one hand holding the front of the MAU, and your other hand holding the single-slot hub, carefully pull the two units apart. When you install a MAU in a DEChub 900 MultiSwitch, you do not have to turn off the hub power . Remove the single-slot hub (if necessary). If you want to ...
-
Digital Media 900TL - page 6
Connect station cables to any available lobe connector on the MAU. For 150-ohm applications, you also need an impedence matching transformer cable (Digital part number BN26T -03). Connect station cables. 4 PK–02570–IL Installing a MAU in a DEChub 900 MultiSwitch (continued) 6 DECmau 900TL V erify power . 3 With power on in the hub, verify that ...
-
Digital Media 900TL - page 7
a. Set the Ring In and the Ring Out Autowrap switches to 1 or 0. b. Set the switch to 1 to enable Autowrap when the Ring In or Ring Out port connects to a device with Digital’s Auto wrap, there is only one MAU in the network, or the port is not connected to the network. Otherwise, set the switch to 0 to disable Autowrap. Mount MAU (optional). 1 C ...
-
Digital Media 900TL - page 8
If a MAU is being added to an existing network, connect Ring In to the Ring Out connector of a MAU or repeater , and connect Ring Out to the Ring In connector of a MAU or repeater . Connect station cables. 4 Check LEDs. 6 With power on, verify that the Power and Module OK LEDs are on. Install a MAU to adjacent MAUs or repeaters. 5 Connect station c ...
-
Digital Media 900TL - page 9
Removing a MAU from a DEChub 900 MultiSwitch a. Lift up the Release lever on the hub. b. Pivot the MAU back on its bottom mounting tab until it disengages from the hub. DECmau 900TL 9 Note: When you remove a MAU from the hub, do not turn off the hub power . Remove the MAU from the hub. 1 2 Disconnect the station connector cables from the MAU. The r ...
-
Digital Media 900TL - page 10
LED Summary LED 1 Off On Flashing Power No Power Power OK Module OK Self-test failed Self-test OK or not operating 4/16 Mb/s No activity V alid speed or management set speed Lobe Inactive Connected to network Continuous single flash: network management disabled port. Continuous double flash: wrong speed. Hub MAU ONL Y : Ring A/B Not connected Conne ...
-
Digital Media 900TL - page 11
Cabling T able 1 lists the T oken Ring industry guideline for the maximum lobe length of shielded twisted-pair (STP) and unshielded twisted-pair (UTP) cable. T able 1 Industry Lobe Length Guideline Lobe lengths for Digital’s MAUs exceed the industry guideline. Specifically , lobe lengths can be longer than the industry guideline for STP cable and ...
-
Digital Media 900TL - page 12
Cabling (continued) Digital recommends that you use repeaters to segment the ring in a network with multiple wiring closets. In some situations, only one, or no repeaters, are required. Refer to the appropriate T oken Ring repeater manual for specific information. When distances exceed the lobe lengths in T able 2, or if the MAU does not have Digit ...
-
Digital Media 900TL - page 13
Problem Solving If ... Then ... Do This ... DEChub 900 MultiSwitch and DEChub ONE Power LED is off. MAU does not have power . V erify that outlet has power . Check power connection to MAU. Replace power supply . Replace MAU. Module OK LED is off. MAU failed self-test. Replace MAU. Ring A and B LEDs alternately MAU needs an upgrade If you have netwo ...
-
Digital Media 900TL - page 14
Problem Solving (continued) If ... Then ... Do This ... DEChub 900 MultiSwitch ONL Y Lobe, Ring In, Ring Out, Network management has T o change settings, you can use Ring A/B LEDs flash together . disabled MAU. network management commands or the MAU’s Reset switch. MAU does not connect to Network management will not Check speed and hub hub. conne ...
-
Digital Media 900TL - page 15
Product Specifications Product Specification In a Hub DEChub ONE Size 27.3 x 1 1.2 x 3.2 cm 27.3 x 17.0 x 3.2 cm (10.8 x 4.4 x 1.2 inches) (10.75 x 6.7 x 1.25 inches) Weight .82kg (1.5 lb) 1.09kg (2.0 lb) Operating temperature 5 ° C to 50 ° C (41 ° F to 122 ° F) 5 ° C to 50 ° C (41 ° F to 122 ° F) Relative humidity 10% to 95% non-condensing ...
¿Tienes una pregunta acerca de Digital Media 900TL?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Digital Media 900TL, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Digital Media 900TL probablemente compartirá una forma de solucionarlo.