Manual de instrucciones Vulcan-Hart VGC6024 ML-114834

20 de páginas 0.14 mb
Descargar

Pasar a la página of 20

Summary
  • Vulcan-Hart VGC6024 ML-114834 - page 1

    VGC SERIES GAS CONVEYOR OVENS MODELS VGC3018 ML-126196 VGC3624 ML-114829 VGC3632 ML-114830 VGC4018 ML-126197 VGC4824 ML-114831 VGC4832 ML-114832 VGC6024 ML-114834 VGC6032 ML-114835 VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 FORM 31057 (5-98) INST ALLA TION & OPERA TION MANUAL ...

  • Vulcan-Hart VGC6024 ML-114834 - page 2

    — 2 — IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OB ...

  • Vulcan-Hart VGC6024 ML-114834 - page 3

    — 3 — T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Unpacking . . . . . . . . ...

  • Vulcan-Hart VGC6024 ML-114834 - page 4

    — 4 — Installation, Operation and Care of MODEL VGC SERIES GAS CONVEYOR OVENS PLEASE KEEP THIS MANUAL FOR FUTURE USE GENERAL Vulcan ovens are produced with quality workmanship and material. Proper installation, usage and maintenance of your oven will result in many years of satisfactory performance. It is suggested that you thoroughly read this ...

  • Vulcan-Hart VGC6024 ML-114834 - page 5

    — 5 — When installed, minimum clearance from combustible and non-combustible construction must be 2.5" (63.5 mm) at the sides and 2.5" (63.5 mm) at the rear. The installation location must allow adequate clearances for servicing and proper operation. A minimum front clearance of 36" (914.4 mm) is required. Do not obstruct the flo ...

  • Vulcan-Hart VGC6024 ML-114834 - page 6

    — 6 — PL-41122 ASSEMBLY Ovens Mounted on Legs or Feet To service the oven when mounted on legs or feet, a minimum clearance of 18" (457 mm) from service compartment is required. Ovens Mounted on Casters NOTICE: In order to be able to service this appliance, it must be installed with the casters supplied, a connector complying with ANSI Z21 ...

  • Vulcan-Hart VGC6024 ML-114834 - page 7

    — 7 — LEVELING Casters for this oven are of the non-adjustable type. Therefore, the floor must be level. If floor surface is not level, the oven will experience cooking problems. GAS CONNECTIONS Gas supply connections and any pipe joint compound must be resistant to the action of propane gases. Location of the 3 ⁄ 4 " gas inlet is at the ...

  • Vulcan-Hart VGC6024 ML-114834 - page 8

    — 8 — PL-41 147-1 TEMPERA TURE DISPLA Y LOAD INDICA T OR LIGHT TIME DISPLA Y BEL T SWITCH TIME KNOB POWER SWITCH TIME RANGE SWITCH READ SET POINT BUTT ON OPERA TION WARNING: THE OVEN AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE OVEN. CONTROLS (Fig's. 2 and 3) Fig. 2 Temperature Display — Displays actua ...

  • Vulcan-Hart VGC6024 ML-114834 - page 9

    — 9 — Belt Switch — Push switch to ON to start the conveyor belt; push to OFF to stop the conveyor belt. Power Switch — Push to ON to start the oven; push to OFF to stop the oven. When the power switch is pushed to ON, ignition occurs automatically. Time Knob — After the Time Range Switch has been set to the desired time range, turn the k ...

  • Vulcan-Hart VGC6024 ML-114834 - page 10

    — 10 — PL-41 123-1 TIME DISPLA Y TEMPERA TURE DISPLA Y BEL T SWITCH TIME KNOB POWER SWITCH SET POINT TIME RANGE SWITCH SET POINT ARROWS CONTROL CIRCUIT FUSE DRIVE MOTOR FUSES SET POINT INDICA TOR LIGHT ALTERNATE CONTROLS (Fig. 4) Temperature Display — Displays actual oven cavity temperature during cooking cycle. Set Point — Push to display ...

  • Vulcan-Hart VGC6024 ML-114834 - page 11

    — 11 — PL-41125-1 GAS COMBINA TION CONTROL V AL VE If the burner fails to light within 90 seconds, the burner control will shut off the gas combination valve and will lock out. To reset the burner control for restart, push the Power Switch to OFF and then to ON. If the burner still fails to light, turn the oven off and wait for 5 minutes before ...

  • Vulcan-Hart VGC6024 ML-114834 - page 12

    — 12 — PL-41 126-1 THUMB SCREWS BAFFLE Turning the Oven Off Turn Power Switch to OFF. Extended Shutdown Turn Power Switch to OFF. Turn gas combination valve to OFF. Turn main gas shutoff valve to OFF. USING THE OVEN When power is applied to the oven, it will begin operating at the factory set temperature of 525 ° F (273 ° C). The actual oven ...

  • Vulcan-Hart VGC6024 ML-114834 - page 13

    — 13 — PL-41 127-1 CRUMB TRA YS Air Distribution Panels The oven is equipped with a top and a bottom air distribution panel. These panels regulate the quantity of air on the top and bottom of the product that is being cooked. They have been adjusted at the factory for proper baking performance. Some products may need additional panel adjustment ...

  • Vulcan-Hart VGC6024 ML-114834 - page 14

    — 14 — PL-41 128-1 BEL T TENSION SCREWS Conveyor To maintain proper belt tension the conveyor belt will have to be adjusted to remove any slack in the belt. 1. To tension the belt, locate the two adjustment screws (Fig. 8) on the right hand end (facing machine) of the conveyor assembly. Loosen the nuts on the inside of the of the conveyor rack ...

  • Vulcan-Hart VGC6024 ML-114834 - page 15

    — 15 — PL-41130 PL-41129-1 REMO VE COVER 2. Conveyor Assembly Removal a. Remove conveyor crumb trays (see Fig. 7). b. Remove cover where conveyor shaft enters the left-hand control box (Fig. 9). Fig. 9 Fig. 10 c. Lift up the drive end of the conveyor assembly and slide the conveyor assembly into the oven tunnel to remove the tension on the driv ...

  • Vulcan-Hart VGC6024 ML-114834 - page 16

    — 16 — PL-41131 Weekly CAUTION: Intake fans and slots on the back of the oven and control box must be cleaned weekly. Any obstructions may cause motor damage. Use a long bristle brush to clean these areas. Fig. 11 e. Pull the entire conveyor assembly from the oven (Fig. 11). f. Take conveyor assembly to cleaning area. g. To replace conveyor ass ...

  • Vulcan-Hart VGC6024 ML-114834 - page 17

    — 17 — CONVEYOR BELT ASSEMBLING AND DISASSEMBLING (Fig. 12) Install the conveyor belt so that it always runs in the direction indicated by this arrow — the closed end of the loop toward the direction of travel. The arrows in the belt illustrate the movement of the splicing strand between steps. When bending the splicing strand, try to limit b ...

  • Vulcan-Hart VGC6024 ML-114834 - page 18

    — 18 — COOKING CHART The times and temperatures shown in this chart are suggested only. Experiment with your food products to determine the cooking temperatures and times that give you the best results. TYPE OF APPROX. TIME TEMP. FOOD PRODUCT (IN MIN.) ( ° F) / ( ° C) ITALIAN Pizza (par baked dough) 4 to 4.5 510 / 265 Pizza (fresh dough) 5.5 ...

  • Vulcan-Hart VGC6024 ML-114834 - page 19

    — 19 — MAINTENANCE WARNING: THE OVEN AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE OVEN. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY BEFORE PERFORMING ANY MAINTENANCE ON THE OVEN. INSPECTION The oven should be inspected at least annually by a Vulcan-Hart authorized servicer. More frequent cleaning may be requi ...

  • Vulcan-Hart VGC6024 ML-114834 - page 20

    — 20 — FORM 31057 (5-98) PRINTED IN U.S.A. TROUBLESHOOTING PROBLEM Power switch is on and oven will not operate. Burner is on but oven does not start. Speed control shows "OL". Conveyor belt does not turn. Conveyor belt jumps. Burner does not ignite. Cooking is not even. Oven gives off gas odors. Oven is operating, temperature control ...

Fabricante Vulcan-Hart Categoría Oven

Los documentos del dispositivo Vulcan-Hart VGC6024 ML-114834 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Vulcan-Hart
- manuales de instrucciones VGC6024 ML-114834
- hojas de producto Vulcan-Hart
- folletos informativos
- o etiquetas energéticas Vulcan-Hart VGC6024 ML-114834
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Vulcan-Hart VGC6024 ML-114834.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Vulcan-Hart VGC6024 ML-114834, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Vulcan-Hart VGC6024 ML-114834. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Vulcan-Hart VGC6024 ML-114834.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Vulcan-Hart VGC6024 ML-114834, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Vulcan-Hart VGC6024 ML-114834. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Vulcan-Hart VGC6024 ML-114834.

El manual de instrucciones completo de Vulcan-Hart debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Vulcan-Hart VGC6024 ML-114834 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Vulcan-Hart VGC6024 ML-114834, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Vulcan-Hart VGC6024 ML-114834 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Vulcan-Hart VGC6024 ML-114834 - que deben facilitarnos los primeros pasos durante el uso de Vulcan-Hart VGC6024 ML-114834
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Vulcan-Hart VGC6024 ML-114834
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Vulcan-Hart VGC6024 ML-114834 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Vulcan-Hart VGC6024 ML-114834?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Vulcan-Hart VGC6024 ML-114834, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Vulcan-Hart VGC6024 ML-114834 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Comentarios (0)