-
Omega EP510 - page 1
omega.com e-mail: info@omega.com For latest product manuals: omegamanual.info EP510, IP510, EP511, IP511 SERIES Electr oneumatic Conver ters Shop online at U ser ’ s Guide MADE IN ...
-
Omega EP510 - page 2
Servicing Nor th America: U.S.A.: Omega Engineering, Inc., One Omega Drive, P.O. Box 4047 ISO 90 01 Cer tif ied Stamford, CT 06907-0047 USA Toll Free: 1-800-826-6342 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec), H7L 5A1 Canada Toll-Free: 1-800-826-6342 TEL: (514) 856-6928 FAX: (514) 856-6886 e-mai ...
-
Omega EP510 - page 3
A IR CONNECTIONS S UPPLY Connect air supply to 1/4 NPT port marked "IN." If the above specifications are not met, possibility of internal clogging exists. Also see MAINTENANCE section. OUTPUT Connect output to 1/4 NPT port marked "OUT." G AUGE The plugged 1/8 NPT port in the base of the transducer is internally connected with th ...
-
Omega EP510 - page 4
M EP510 AND IP510 OUNTING GENERAL NEMA 1 and NEMA 4X transducers can be mounted in any position. DIRECT MOUNTING PIPE • Any NEMA 1 transducers may be supported by its own plumbing for air supply and output. NEMA 4X transducers may also be supported using 1/2" explosion proof conduit in the electrical port. PANEL • NEMA 1 transducers may be ...
-
Omega EP510 - page 5
E LECTRICAL CONNECTIONS P RECAUTIONS TO BE OBSERVED DURING INSTALLATION These Transducers were tested at the EMC Test Centre, Dunfermline, Fife, KY11 5LB to the Electromagnetic Compatibility Directive effective January 1, 1996. The relevant EMC specifications tested were the following: EN 50081-1 (1992) and EN 50082-2 (1992). A Technical Constructi ...
-
Omega EP510 - page 6
WARNING: In explosive atmospheres, electrical power must be removed from the transducer before attempting to remove the cover and until the cover is fully reinstalled. Failure to do so may result in electrical spark or explosion. CAUTION: Only attempt electrical adjustments as described below. Any mechanical adjustments made will void the warranty. ...
-
Omega EP510 - page 7
R EPLACING ORIFICE: T his can be accomplished without removing the unit from its mounting or plumbing. 1. Turn off supply pressure and unscrew the brass orifice assembly located on the side of the housing with the gauge port. NOTE: Small sealing o-ring may remain inside of the housing. If it does, remove it with a paper clip or some other small pro ...
-
Omega EP510 - page 8
EXPLOSION & DUST-IGNITION PROOF CERTIFICATIONS F ACTORY MUTUAL and CANADIAN STANDARDS ASSOCIATION WARNING: The following ratings are valid ONLY WHEN the cover is installed for FM and CSA. BOTH the cover and the locking device, using tamper resistant screws must be installed. Screws are to be removed and installed with a special driver bit (supp ...
-
Omega EP510 - page 9
M- 410 9/1 10 4 I P5 10, EP 51 0, IP 511 , EP5 11 SE RIE S A 9 TABLE 5: KITS KIT NAME PART NUMBER 1. Panel Mounting Kit 010135-000 2. Valve Mounting Kit 010134-000 3. 2" Pipe Mounting Kit (Valve Mounting Kit is required) 010143-000 4. DIN Rail Adapter 010115-000 5. Cover Locking Device Kit (for NEMA 4X enclosure only) 010136-000 6. Zero based ...
-
Omega EP510 - page 10
M- 410 9/1 10 4 I P5 10, EP 51 0, IP5 11 , E P5 11 SE RIE S A 10 510 and 511 Series I/P AND E/P TRANSDUCER SPECIFICATIONS Accuracy: ± 0.10% of output span, typical ± 0.25% of output span, maximum Hysteresis: 0.01% of output span, typical 0.10% of output span, maximum Dead Band: Not measurable Repeatability: 0.01% of output span, typical 0.10% of ...
-
Omega EP510 - page 11
W ARRANTY / DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months fro m da te of pu rcha se. OMEGA ’ s W ARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA ’ s c ...
-
Omega EP510 - page 12
M4109/0909 Where Do I Find Ever ything I Need for Pr ocess Measurement and Control? OM EGA…Of Course! Shop online at omega.com SM TEMPERA TURE 䡺 ⻬ Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies 䡺 ⻬ Wire: Thermocouple, RTD & Thermistor 䡺 ⻬ Calibrators & Ice Point References 䡺 ⻬ Recorders, Con ...
¿Tienes una pregunta acerca de Omega EP510?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Omega EP510, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Omega EP510 probablemente compartirá una forma de solucionarlo.