Español dropdown-ico

Manual de instrucciones Holman qt14

28 de páginas 2.71 mb
Descargar

Pasar a la página of 28

Summary
  • Holman qt14 - page 1

    2M-HG0500 Rev C 2/22/06 10 SUNNEN DRIVE, ST. LOUIS, MO/U.S.A. 63143 PHONE (314) 781-2777 FAX (314) 781-3636 A Star Manufacturing Compa ny HOLMAN CONVEYOR SANDWICH WARMER MANUAL MODEL QT14 FOR SERVICE INFORMATION U. S. AND CANADA CALL: TOLL FREE 1-800-807-9054 SUBJECT TABLE OF CONTENTS PAGE UNCRATING AND INSPECTION 1 ASSEMBLY AND INSTALLATION 1 & ...

  • Holman qt14 - page 2

    Common Questions, Myths, and Misconceptions of Holman Conveyor Ovens Misconception: High Voltage (208v typical) is always the same. Reality: An oven designed for 208v should operate from 208-215v. This range is typical of local power grids and daily fluctuations. Some municipalities operate at 220 and 240v which would require design vari ations. Im ...

  • Holman qt14 - page 3

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 1 UNCRATING AND INSPECTION Unpack unit and components from container. Remove all visible packing material, inspect unit for damage. If damage is discovered, file a claim immediately with the carrier that handled the shipment. The following should be includ ...

  • Holman qt14 - page 4

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 2 5. Allow approximately 5 to 8 minutes for the twin-fan cooling system to come on. Check the air intake fan area as noted below and be sure that there is a sufficient flow of air into the control box. 6. If all heaters and conveyor system are operating pr ...

  • Holman qt14 - page 5

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 3 OPERATION 1. Turn Master On/Off switch to the ON position and variable speed control to fastest time setting. Allow 1 hour for complete machine warm up. 2. Adjust speed control to desired speed. 3. Adjust speed as required during operation to achieve a g ...

  • Holman qt14 - page 6

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 4 2. Remove the Crumb Trays from both sides of the oven (daily) as shown below (DO NOT CLEAN WITH CAUSTIC CLEANERS) . 3. For lightly soiled conveyor surfaces a damp cloth or scotch pad can be used without removing the conveyor belt. (daily) For heav ily so ...

  • Holman qt14 - page 7

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 5 TROUBLESHOOTING GUIDE # UNIT WILL NOT HEAT, CONVEYOR BELT WILL NOT TURN. o Be sure main circuit breaker is switched to the ON position. o Check that the unit is connected to power and Master On/Off switch is O N. o Be sure HEAT LIMIT SWITCH is pushed in ...

  • Holman qt14 - page 8

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 6 # CONVEYOR WILL NOT TURN, UNIT HEATS PROPERLY o DISCONNECT UNIT FROM POWER SOURCE o Check both fuses (replace if necessary) o Check for obstructions that may have caused a conveyor jam. Utensils, foil or large pieces of food could stall the motor. If the ...

  • Holman qt14 - page 9

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 7 PREVENTIVE MAINTENANCE DAILY CLEANING PROCEDURES TO KEEP YOUR HOLMAN MODEL QT14 CONVEYOR SANDWICH WARMER AT PEAK OPERATING EFFICIENCY, TH E FOLLOWING INSTRUCTIONS ARE RECOMM ENDE D: Turn power off and allow cooling fans to run until the control box is co ...

  • Holman qt14 - page 10

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 8 4. Wipe exterior of unit with a damp cloth. 5. Wipe fan grills/air intakes (located on si de of t he unit) to remove an y dust build up using a damp cloth. Reassemble unit making sure cru mb trays ar e properly installed. The cru m b tray sho uld slide i ...

  • Holman qt14 - page 11

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 9 WEEKLY CONVEYOR BELT CLEANING PROCEDURES TO KEEP YOUR HOLMAN MODEL QT14 CONVEYOR SANDWICH WARMER AT PEAK OPERATING EFFICIENCY, TH E FOLLOWING INSTRUCTIONS ARE RECOMM ENDE D: Turn power off and allow cooling fans to run until the control box is cooled off ...

  • Holman qt14 - page 12

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 10 MONTHLY CLEANING PROCEDURES Turn power off and allow cooling fans to run until the control box is cooled off. The fans are controlled by a thermostat in the control box. DISCONNECT UNIT FRO M POWER S UPPLY OR TURN POWER OFF AT WALL BREAKE R. BE SURE THE ...

  • Holman qt14 - page 13

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 11 3. Clean air intake on the side of Sandwi ch Warmer by vacuuming a ny dust and d ebris built up on fan grill. 4. Return unit to counter and remove screw holdi ng power supply side pan el in place. Carefully lift panel up and out. Two ground straps hold ...

  • Holman qt14 - page 14

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 12 LONG TERM CLEANING PR OCEDURES (every 6 months) Turn power off and allow cooling fans to run until the cont rol box is cooled off. The fans are controlled by a thermostat in the control box. DISCONNECT UNIT FROM POWER S UPPLY OR TURN POWER OFF AT WALL B ...

  • Holman qt14 - page 15

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 13 MAINTENANCE PROCEDURES REPLACING HEATER TUBES FOR BEST TOASTING PERFORMANCE, THIS PROCEDURE SHOULD BE DONE EVERY SIX MONTHS Turn power off and allow cooling fans to r un until the control box is cooled off. The fans are controlled by a thermostat in the ...

  • Holman qt14 - page 16

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 14 8. Gently slide one heater tube out of hole in warmer wall. 9. Select new heater tube to be installed. To ease installati on, a short piece of tubing such as a n automotive bra ke line or sipping straws may be used. Insert heater tub e wire in to one en ...

  • Holman qt14 - page 17

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 15 REPLACING FAN MOTORS Turn power off and allow cooling fans to run until the control box is cooled off. DISCONNECT UNIT FRO M POWER S UPPLY OR TURN POWER OFF AT WALL BRE AKER. NOTE: PERFORM THIS MAIN TENANCE ONLY WHEN THE CONVEYOR SANDWICH WARMER IS COMP ...

  • Holman qt14 - page 18

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 16 DRIVE CHAIN DRIVE SPROCKET DRIVEN SPROCKET REPLACING BELT DRIVE MOTOR Turn power off and allow cooling fans to run until the control box is cooled off. DISCONNECT UNIT FRO M POWER S UPPLY OR TURN POWER OFF AT WALL BRE AKER. NOTE: PERFORM THIS MAIN TENAN ...

  • Holman qt14 - page 19

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 17 Note: During factory assembly, a 1/8” side-to-si de play is adjusted into the driveshaft to allow for chassis expa nsion. 1. Unit must be cool 2. Do not adjust the sprocket on the driveshaft. 3. Insert a 1/16” spacer (drill bit etc) between the driv ...

  • Holman qt14 - page 20

    Part# 2M-4497-2 10/05 RB The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty. FOR ASSISTANCE Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department. In all correspondence mention the Model nu ...

  • Holman qt14 - page 21

    ...

  • Holman qt14 - page 22

    OPERA T I N G IN S T R UC TION S PR I OR T O O PENING: Q TURN POWE R ON T O BE G IN P REHEAT Q S ET C O N V E Y OR SPEED T O D E SI RED S E TTIN G D URING B USINES S HOURS: Q OB SE R VE BAK E ON SAN DW I CHES, REVIS E SETT I NGS TO ACHIEV E A B A K E TO QU I ZN OS STAND ARDS A T C L O SE: Q TURN PO W ER O F F FAN OPER ATES U N T IL UN IT C OOL S 16 ...

  • Holman qt14 - page 23

    P ARTS LIST February 23, 2007, Rev D IMPORT ANT : WHEN ORDERING, INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. Number Per Unit Description and Model Designation MODEL Part Number Key Number HOLMAN CONVEYOR SANDWICH W ARMER QT14 - QT14R 1 GE-100715 1 BEL T SUPPOR ...

  • Holman qt14 - page 24

    P ARTS LIST February 23, 2007, Rev D IMPORT ANT : WHEN ORDERING, INCLUDE MODEL AND SERIAL NUMBER Some items are included for illustrative purposes only and in certain instances may not be available. Number Per Unit Description and Model Designation MODEL Part Number Key Number HOLMAN CONVEYOR SANDWICH W ARMER QT14 - QT14R PS-Z10286 INCLUDES: 2U-Z96 ...

  • Holman qt14 - page 25

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 20 DETAIL OF RESISTOR/DIODE TERMI NAL BL OCK 47 OHM DIODE WIRING DIAGRAM #020514A QT14 W/ POT SPEED CONTROL THREE PHASE DELTA SOURCE 250 OHM POT (PART OF GE-13570 2) WHT BLK BLK WHT RED RED BLK WHT WHT RED WHT BLK YEL BLK RED WHT BLK ORN YEL BLK BLU YEL WH ...

  • Holman qt14 - page 26

    IF FURTHER ASSISTANCE IS REQUIRED: CONTACT STAR/HOLMAN FACTORY SERVICE TEAM AT 1-800-807-9054 21 W IR IN G DIA G RA M #020513A Q T 1 4 W / P O T S P EED CON TROL S I N G L E P H A S E - 208/220/ 240 PU R YE L BL U ORN ORN BL U YE L BL K BL K WH T WH T BL K WH T WH T WH T BL K BLK WH T BL K BL K BL U YE L BL K PU R WH T WH T BL K BL K RE D MOLD E D ...

  • Holman qt14 - page 27

    FA N SWITCH PILOT LIGHT RESET SWITCH ON/OFF FUSE FUSE L2 L3 Gnd L1 N BOTTOM HEA TERS TOP HEA TERS WINDOW SIDE CONTROL SIDE DRIVE MOTOR: USE BLK/WHT FOR 208V USE BLK/BLU FOR 240V 250 OHM POT (P ART OF GE-135702) MODEL: QT14 380/220/60 3 phase, 15 TUBE - SERIES THIS DRA WING CONT AINS INFORMA TION CONFIDENTIAL TO ST AR MFG. INT'L. INC. NO REPROD ...

  • Holman qt14 - page 28

    ST AR MANUF ACTURING 10 Sunnen Drive, St. Louis, MO 63143 U.S.A. (800) 807-9054 (314) 781-2777 Parts & Service (800) 807-9054 www .star-mfg.com ...

Fabricante Holman Categoría Oven

Los documentos del dispositivo Holman qt14 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Holman
- manuales de instrucciones qt14
- hojas de producto Holman
- folletos informativos
- o etiquetas energéticas Holman qt14
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Holman qt14.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Holman qt14, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Holman qt14. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Holman qt14.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Holman qt14, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Holman qt14. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Holman qt14.

El manual de instrucciones completo de Holman debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Holman qt14 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Holman qt14, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Holman qt14 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Holman qt14 - que deben facilitarnos los primeros pasos durante el uso de Holman qt14
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Holman qt14
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Holman qt14 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Holman qt14?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Holman qt14, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Holman qt14 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)