-
American Dynamics AD1689B - page 1
Model 1689B General Purpose 8-Channel Receiver Installation Instructions This manual describes the installation and operating procedures for the 1689B Eight-Channel Receiver. Receivers are designed as the remote control device for operation of a motorized pan & tilt unit and a motorized lens unit. Since camera sites are often a great distance f ...
-
American Dynamics AD1689B - page 2
This software/firmware is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software is furnished to the purchaser under a license for use on a single system. NOTE: Information furnished by SENSORMATIC is believed to be ...
-
American Dynamics AD1689B - page 3
The installation of this product should be made by qualified service personnel and should conform to all local codes. QA301D ! W W W W A A A A R R R R N N N N II I I N N N N G G G G To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture. AMERICAN DYNAMICS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMO ...
-
American Dynamics AD1689B - page 4
...
-
American Dynamics AD1689B - page 5
T able of Contents Product Description ................................................1 Features ..................................................................1 Setup .......................................................................2 Installation ..............................................................3 Cable Connections .......... ...
-
American Dynamics AD1689B - page 6
...
-
American Dynamics AD1689B - page 7
PRODUCT DESCRIPTION The 1689B Receiver is used with matrix switching systems to control pan, tilt, zoom, focus, iris and auxiliary functions at a camera site. This receiver is classified as an eight-channel type since eight independent control channels are supplied. The 1689B will control, depending on factory configuration, eight (8) cameras with ...
-
American Dynamics AD1689B - page 8
SETUP There are eight pairs of rotary BCD switches which associate the camera identifiers with their respective channel. The locations of S1 through S16 on the PCB are shown in Figure 1 below. Rotary switches S1 and S2 are for the camera assigned to channel 1, switches S3 and S4 are for the camera assigned to channel 2, etc. The first switch of eac ...
-
American Dynamics AD1689B - page 9
INSTALLATION This installation should be made by qualified service personnel and should conform to all local codes. Safeguards must be taken to avoid unintentional operation by employees and maintenance personnel working about the premises, by falling objects, by customers, by building vibration, and by similar causes. Preparation There are many us ...
-
American Dynamics AD1689B - page 10
CABLE CONNECTIONS Code Line Connections The Control Code line connection to the receiver is made with user-supplied, shielded 2-wire twisted pair, Belden 8760 or equivalent (for Plenum, use Belden 88760 or equivalent). The maximum code line length is 5000 feet. The code line connector, J4, is a 4-position terminal strip located near the rotary swit ...
-
American Dynamics AD1689B - page 11
Pan/Tilt and Lens Cable The connections to a Pan/Tilt and a motorized lens are with 12-pin connectors. These connectors are located on the PCB, in the front of the unit with the power switch in the upper left corner. They are labeled J101 to J801 and OUT 1 to OUT 8, respectively (see Figure 1 or OP0064, OP0065 or OP0066). Before Starting: 1. Check ...
-
American Dynamics AD1689B - page 12
Auxiliary Cable If the unit is configured with auxiliaries, they are connected by 12-pin connectors. For four auxiliaries these connectors, labeled J201, J401, J601 and J801 (OUT 2, OUT 4, OUT 6 and OUT 8) respectively, are located in the front of the PCB (see OP0065 or OP0066 for four and eight auxiliaries, respectively). For eight auxiliaries the ...
-
American Dynamics AD1689B - page 13
Power Input CAUTION - The following instructions for power input require the installer to gain access to internal terminals and power wiring which involve hazardous voltages and the risk of electric shock. Power wiring must be done only by qualified electricians or service personnel and should conform to local codes. See instructions provided with ...
-
American Dynamics AD1689B - page 14
...
-
American Dynamics AD1689B - page 15
Appendix ...
-
American Dynamics AD1689B - page 16
...
-
American Dynamics AD1689B - page 17
...
-
American Dynamics AD1689B - page 18
...
-
American Dynamics AD1689B - page 19
...
-
American Dynamics AD1689B - page 20
...
-
American Dynamics AD1689B - page 21
...
-
American Dynamics AD1689B - page 22
...
-
American Dynamics AD1689B - page 23
...
-
American Dynamics AD1689B - page 24
...
-
American Dynamics AD1689B - page 25
...
-
American Dynamics AD1689B - page 26
...
-
American Dynamics AD1689B - page 27
...
-
American Dynamics AD1689B - page 28
An American Dynamics Product Designed and built by Sensormatic Video Systems Division One Blue Hill Plaza Pearl River, New York, 10965 Business: (845) 624-7600 Technical Support Center: 1-800-442-2225 FAX: (845) 624-7685 8000-0871-01 Rev E OP1689BE February, 1998 Printed in USA SPECIFICATIONS Supply Voltage: AD1689B-8 120 VAC, 50/60 Hz AD1689B8-X 2 ...
¿Tienes una pregunta acerca de American Dynamics AD1689B?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con American Dynamics AD1689B, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con American Dynamics AD1689B probablemente compartirá una forma de solucionarlo.