Manual de instrucciones Microsoft SHG-TC

16 de páginas 0.52 mb
Descargar

Pasar a la página of 16

Summary
  • Microsoft SHG-TC - page 1

    SHG-A* Absolute, SHG-TC, SHG-TS & SHG-VS Linear Encoders NEWALL MEASUREMENT SYSTEMS LTD N Installation Manual THIS MANUAL SHOULD BE USED IN CONJUNCTION WITH WITH THE CORRESPONDING PROTOCOL DOCUMENT ...

  • Microsoft SHG-TC - page 2

    Newall Measurement Systems Contents 1 CONTENTS 1.0 Technical Specification ..............................................1 1.1 Bracketry ..............................................................................2 1.2 Preparation ..........................................................................2 1.3 Warnings ............................ ...

  • Microsoft SHG-TC - page 3

    Introduction Newall Measurement Systems 2 1.0 INTRODUCTION This manual will provide connection and mounting instructions for Newall's Absolute, Digital and Distance Coded linear encoders. It is important that you read and understand this manual prior to commencing the hardware installation. Electronic specifications can be found in the corresp ...

  • Microsoft SHG-TC - page 4

    Figure 3.1 - Alignment of the reader head 2.0 ENCODER ASSEMBLY Item Description 1 Reader Head 2 Scale 3 Scale Support Link 4 Scale Anchor Pin 5 Support Pillar Short Item Description 6 Support Pillar Long 7 Scale Cover 8 M5 Nut 9 M8 x Socket Button Head Newall Measurement Systems 3 Encoder Assembly / Mounting the Reader Head 3.0 MOUNTING THE READER ...

  • Microsoft SHG-TC - page 5

    Mounting the Scale Newall Measurement Systems 4 4.0 MOUNTING THE SCALE 4.1 Double End Mounting Note: Refer to section 4.3 for mounting scales in excess of 2.5 metres. Each end of the scale is different and can be identified by the “calibration adjustment end” and the “fixed end. NOTES: (A) Erroneous readings will occur if the reader head is a ...

  • Microsoft SHG-TC - page 6

    Mounting the Scale A maximum of two support pillars may be screwed together to allow for sufficient adjustment of the scale. If two pillars are insufficient to enable the scale to be mounted, then additional brackets will be necessary. These brackets must be sufficiently rigid to eliminate any axial movement of the scale. Loosely fit the support li ...

  • Microsoft SHG-TC - page 7

    Mounting the Scale Newall Measurement Systems 6 Remove the link/pin assembly and the scale from the reader head. Drill and tap M8 x 18mm deep (USA 5/16" -18 x 3/4" deep) into the machine casting as marked by the transfer punch. Fit the pillar(s) to the machine casting by using one of the methods shown in Figure 4.3. The pillar shoulder fi ...

  • Microsoft SHG-TC - page 8

    Mounting the Scale 4.3 Scales in Excess of 2.5 Meters Traverse the machine to fullest extent of travel including hand winding past any electrical limits or trip dogs. Insert the set up tube into the reader head, allowing for a sufficient amount of scale to project from the reader head in order to fit the scale mounting brackets. Assemble the angle ...

  • Microsoft SHG-TC - page 9

    Newall Measurement Systems 8 Mounting the Scale For scales which are mounted in the horizontal position, spring loaded scale supports are included and should be positioned according to Table 1. Once the locations for the supports have been determined, the reader head should be positioned in the location where the first support is to be fitted. Asse ...

  • Microsoft SHG-TC - page 10

    Mounting the Scale / Fitting the Scale Guard Length 2500mm 3000mm 3500mm 4000mm 4500mm 5000mm 5500mm 6000mm 6500mm 7000mm 7500mm 8000mm 8500mm 9000mm 9500mm 10000mm 10500mm 11000mm No. of Scale Supports 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 6 6 6 Left Side (A) 850mm 1100mm 1350mm 1500mm 1125mm 1250mm 1350mm 1500mm 1300mm 1400mm 1500mm 1600mm 1410mm 1500mm ...

  • Microsoft SHG-TC - page 11

    Newall Measurement Systems 10 Cable Routing / Final Check 6.0 CABLE ROUTING The most important and the most over looked aspect of fitting the linear encoder is proper cable routing. Dangling and loose cables can be snagged or broken causing irreparable damage. Care should be taken in order to ensure that the cables are secured to the machine and th ...

  • Microsoft SHG-TC - page 12

    Appendix A Newall Measurement Systems 11 Appendix A - SCALE BRACKET MOUNTING OPTIONS Outboard scale support mounting Scale supports inverted ...

  • Microsoft SHG-TC - page 13

    Appendix B Newall Measurement Systems 12 Appendix B - DIMENSIONAL DRAWING ...

  • Microsoft SHG-TC - page 14

    Appendix B (cont’d) Newall Measurement Systems 13 Appendix B - DIMENSIONAL DRAWING ...

  • Microsoft SHG-TC - page 15

    Notes Newall Measurement Systems 14 ...

  • Microsoft SHG-TC - page 16

    NEWALL MEASUREMENT SYSTEMS LTD 023-80620 /03 -UK . O ct 2006 HEAD OFFICE Newall Measurement Systems Ltd. Technology Gateway, Cornwall Road South Wigston Leicester LE18 4XH United Kingdom Telephone: +44 (0)116 264 2730 Facsimile: +44 (0)116 264 2731 Email: sales@newall.co.uk Web: www.newall.co.uk Newall Electronics, Inc. 1778 Dividend Drive Columbus ...

Fabricante Microsoft Categoría Outdoor Ceiling Fan

Los documentos del dispositivo Microsoft SHG-TC que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Microsoft
- manuales de instrucciones SHG-TC
- hojas de producto Microsoft
- folletos informativos
- o etiquetas energéticas Microsoft SHG-TC
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Microsoft SHG-TC.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Microsoft SHG-TC, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Microsoft SHG-TC. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Microsoft SHG-TC.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Microsoft SHG-TC, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Microsoft SHG-TC. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Microsoft SHG-TC.

El manual de instrucciones completo de Microsoft debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Microsoft SHG-TC - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Microsoft SHG-TC, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Microsoft SHG-TC que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Microsoft SHG-TC - que deben facilitarnos los primeros pasos durante el uso de Microsoft SHG-TC
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Microsoft SHG-TC
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Microsoft SHG-TC en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Microsoft SHG-TC?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Microsoft SHG-TC, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Microsoft SHG-TC probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Comentarios (0)