-
Miele DA 210-2 - page 1
Operating and installation instructions Cook er hoods D A 200-2, D A 200-2 EXT , D A 210-2, D A 210-2 EXT , D A 220-2, D A 220-2 EXT It is essential to read these operating instructions before installing or using the machine, to avoid the risk of accidents or damage to the machine. GiWOZr M.-Nr . 05 814 390 ...
-
Miele DA 210-2 - page 2
Caring for the en vir onment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 W arning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description of the appliance DA 200-2, DA 200-2 EXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Miele DA 210-2 - page 3
Disposal of the packing material The transport and protective packing has been selected from materials which are envir onmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed safely and kept out of the reach of babies and young children. Danger of suf focation! Rather than just throwi ...
-
Miele DA 210-2 - page 4
This appliance conforms to current safety requir ements. Incorrect use can however lead to personal injury and damage to the appliance. Before installation and befor e using for the fist time, read the operating instructions carefully . They contain important infor mation on safety , in - stallation, use and maintenance of the appliance. This way y ...
-
Miele DA 210-2 - page 5
The appliance is only completely isolated from the electricity supply when: – it is switched off at the wall socket and the plug removed (do not pull on the cable, only on the plug), or – the fuse from the fused spur connec - tion unit is withdrawn, or – the mains fuse is withdrawn, or – the screw-out fuse is r emoved in countries where thi ...
-
Miele DA 210-2 - page 6
Installation The minimum safety distance be - tween the top of the cooker / hob and the bottom of the cooker hood should be at least: – 550 mm above electric hobs and cookers, – 650 mm above gas hobs and cookers, – 650 mm above an open grill from our range For non-Miele cooking appliances maintain the safety distance as recom - mended by the ...
-
Miele DA 210-2 - page 7
When using the cooker hood at the same time as another heating ap - pliance which depends on the air in the room (e.g. gas, oil or coal fir ed heaters, continuous flow or other water heaters, gas cooker , gas hob or gas oven), spe - cial care must be taken as the action of the cooker hood extracts air from the room, which these type of heaters need ...
-
Miele DA 210-2 - page 8
D A 200-2, D A 200-2 EXT Description of the appliance 8 ...
-
Miele DA 210-2 - page 9
D A 210-2, D A 210-2 EXT Description of the appliance 9 ...
-
Miele DA 210-2 - page 10
D A 220-2, D A 220-2 EXT Description of the appliance 10 ...
-
Miele DA 210-2 - page 11
a Cover plate b To w e r c Canopy d Grease filters e Hob lighting f Controls g Main switc h h T ouch contr ol for the Halogen lighting This control can be used to switch the lighting on and off and is also a dimmer switch. i On/Off touch contr ol for the fan j Controls to select the Fan po wer level k T ouch contr ol for the run-on option This cont ...
-
Miele DA 210-2 - page 12
The cooker hood works with . . . air extraction: The air is drawn in and cleaned by the grease filters and dir ected outside. The cooker hood is fitted with a non-re - turn flap. This flap is closed when the cooker hood is switched off. No ex - change of room air and outside air can take place. When the cooker hood is switched on, the non-return fl ...
-
Miele DA 210-2 - page 13
Main switc h Switch the main switch to "I". The fan and the lighting can now be operated. If the appliance is not going to be used for a longer period of time (e.g. whilst on holiday) switch the appliance off by turning the main switch to "0". The next time it is switched on the cooker hood will operate at the level previously u ...
-
Miele DA 210-2 - page 14
T o switc h the fan off ^ Use the On/Off touch contr ol to switch the fan off. The indicator lamp for the control goes out. Switching the lighting on The hob lighting can be switched on and off independently of the fan. ^ Briefly pr ess the lighting touch con- trol to switch on the hob illumination. The indicator lamp for the touch control lights u ...
-
Miele DA 210-2 - page 15
Filter operating hours counter The number of hours the appliance has been in operation for is stored in mem - ory . The indicator lamp for the grease filter control will light up after 30 hours of op - eration. The grease filters must then be cleaned. After the grease filters have beencleaned and put in place, the filter operating hours counter mus ...
-
Miele DA 210-2 - page 16
Altering the filter operating hours counter The operating hours counter for the grease filters is set to 30 hours. This time can be lengthened or shortened. Y ou can choose from 20, 30, 40 or 50 hours. – Select a short time if you roast or fry a lot. – If you use very little fat for cooking, select a longer time. – If, however , you only cook ...
-
Miele DA 210-2 - page 17
Before any cleaning or maintenance work the cooker hood must be dis - connected from the mains supply . Ensure that: – it is switched off at the fused spur connection unit, or – the mains fuse is withdrawn, or – the screw-out fuse is r emoved (in countries where this is applicable). Housing W ar ning: The surfaces and control switches are sus ...
-
Miele DA 210-2 - page 18
Grease filters The re-usable metal gr ease filters in the appliance remove solid particles from the kitchen vapours (grease, dust, etc) preventing soiling of the cooker hood. The filters should be cleaned regularly (at least every 3-4 weeks) to avoid a build up of fat, but always clean imme - diately the grease filter touch contr ol lamp comes on. ...
-
Miele DA 210-2 - page 19
^ When removing the filters for clean - ing also clean off any r esidues of oil or fat from the now accessible hous - ing to prevent the risk of these catch - ing fire. When replacing the gr ease filters make sure the locking clips ar e visible facing down towards the hob. Should the grease filters be put back upside down: insert a small screwdrive ...
-
Miele DA 210-2 - page 20
Changing a halogen lamp Disconnect the cooker hood from the mains supply . Ensure that: – it is switched off at the fused spur connection unit, or – the mains fuse is withdrawn, or – the screw-out fuse is r emoved (in countries where this is applicable). Exercise caution when changing halogen lamps. They get very hot during use and remain hot ...
-
Miele DA 210-2 - page 21
In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee please contact: – Y our Miele Dealer or – The Miele Service Department (see back cover for address). When contacting the Service Depart - ment, please quote the model and serial number of your appliance. These are shown on the data plate which is v ...
-
Miele DA 210-2 - page 22
D A 200-2, D A 200-2 EXT a Drill holes for fixing to the ceiling with C 8 mm screws b Alternative positions for feeding through the mains supply cable c Cut-out for feeding connection cable through to an external fan, min. 65 x 30 mm d V entilation stub C 150 mm Appliance dimensions 22 ...
-
Miele DA 210-2 - page 23
D A 210-2, D A 210-2 EXT a Drill holes for fixing to the ceiling with C 8 mm screws b Alternative positions for feeding through the mains supply cable c Cut-out for feeding connection cable through to an external fan, min. 65 x 30 mm d V entilation stub C 150 mm Appliance dimensions 23 ...
-
Miele DA 210-2 - page 24
D A 220-2, D A 220-2 EXT a Drill holes for fixing to the ceiling with C 8 mm screws b Alternative positions for feeding through the mains supply cable c Cut-out for feeding connection cable through to an external fan, min. 65 x 30 mm d V entilation stub C 150 mm Appliance dimensions 24 ...
-
Miele DA 210-2 - page 25
Safety regulations pr ohibit the fitting of this cooker hood over a solid fuel stove. For safety reasons a minimum safe distance S must be maintained be - tween the top of the cooker/hob and the bottom of the cooker hood of at least: – 550 mm above electric cookers/hobs, – 650 mm above gas cookers/hobs. – 650 mm above an open grill from our r ...
-
Miele DA 210-2 - page 26
Ceiling plate: D A 200-2, D A 200-2 EXT Ceiling plate: D A 210-2 / 210-2 EXT Ceiling plate: D A 220-2 / 220-2 EXT ^ Address the ceiling plate and posi - tion it exactly . The orange coloured arrow on the ceiling plate must face to the front of the cooker hood. Mark the position of the four holes to be drilled a for securing the ceiling plate and th ...
-
Miele DA 210-2 - page 27
^ If the cooker hood is to be connected to an external fan motor , create the gap for the connection cable to the fan motor . Ensure that the diameter is sufficient to be able to feed thr ough the 6-pole connector . In the following instructions only one type of ceiling plate is shown. ^ Drill four 10 mm C holes in the ceil- ing, and insert S10 plu ...
-
Miele DA 210-2 - page 28
^ Prepar e the ceiling plate for fitting. In- sert the two spring retainers from be- low into the slots provided in the ceil- ing plate. ^ Pull the mains connection cable through the ceiling plate. ^ Insert the four countersunk screws M 6 x 20 into the recessed holes fr om above. Secure the scr ews from above with some adhesive tape to prevent them ...
-
Miele DA 210-2 - page 29
^ Assemble the tower . Place the flange plate of the tower onto the ceiling plate in such a way that the spring clips click into the slots securely . ^ Screw the flange plate secur ely to the ceiling plate with the four M6 nuts supplied. ^ Shorten the electrical connection ca - ble as much as possible and secure inside the cooker hood tower with th ...
-
Miele DA 210-2 - page 30
Danger of toxic fumes. Please heed the "W ar ning and Safety instructions" to avoid the dan - ger of toxic fumes. The cooker hood should be installed according to local building r egula - tions. Seek approval fr om the build - ing inspector where necessary . – All ducting, pipework and fittings must be of non-flammable material. – The ...
-
Miele DA 210-2 - page 31
Important: If the exhaust ducting is to run through rooms, ceiling space etc. wher e there may be great variations in temperatur e between the differ ent areas, the prob - lem of sweating or condensation will need to be addressed. The exhaust ducting will need to be suitably insu - lated. Condensate trap In addition to insulating the exhaust ductin ...
-
Miele DA 210-2 - page 32
All electrical work should be under - taken by a suitably qualified and competent person in strict accor - dance with national and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. The manufactur er can not be held responsible for un - authorised work. Ensure power is not supplied to the appli ...
-
Miele DA 210-2 - page 33
Rated load DA 200-2, 210-2, 220-2 . . . . . . . 280 W Lighting . . . . . . . . . . . . . . . . . . 4 x 20 W V oltage UK, IRL, NZ . . . . . . . . . . . . . . . . . 230 V AUS . . . . . . . . . . . . . . . . . . . . . . . 240 V Frequency . . . . . . . . . . . . . . . . . ~ 50 Hz Fuse rating (UK) . . . . . . . . . . . . . . . 13 A Fuse rating (IRL). . ...
-
Miele DA 210-2 - page 34
34 ...
-
Miele DA 210-2 - page 35
35 ...
-
Miele DA 210-2 - page 36
Alteration rights reserved / 1703 This paper consists of cellulose which has been bleached without the use of chlorine M.-Nr . 05 814 390 / V01 ...
¿Tienes una pregunta acerca de Miele DA 210-2?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Miele DA 210-2, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Miele DA 210-2 probablemente compartirá una forma de solucionarlo.