-
APart REVAMP2250 - page 1
REVAMP2250 Instruction manual ...
-
APart REVAMP2250 - page 2
...
-
APart REVAMP2250 - page 3
Instruction manual REV AMP2250 3 REV AMP2250 Manual ...
-
APart REVAMP2250 - page 4
4 DIGIT AL POWER AMPLIFIER Safety first! • Caution! This professional device needs to be installed by qualified personnel only . • Please check the carton box for any kind of damage on reception of the goods. In case of a damaged carton, please contact your dealer before opening the carton. • !!!! Danger !!!! Exposure to high sound levels m ...
-
APart REVAMP2250 - page 5
Instruction manual REV AMP2250 5 • Set level controls on amplifiers all the way down during power - up to prevent speaker damage if ther e are high signal levels at the inputs. • Do not connect the inputs / outputs of amplifiers or consoles to any other voltage source, such as a battery , mains source, or power supply , regardless of whether ...
-
APart REVAMP2250 - page 6
6 DIGIT AL POWER AMPLIFIER Features • 1 rack unit high • High power Hypex® class-D power amplifier modules • Bridgeable 2 channel amplifier • Dynamic output power: 2x350W @ 4Ω • Sine wave power per channel: 2x250W @ 4Ω (500 msec) • Dynamic bridged output power: 700W @ 8Ω • Bridged Sine wave output power: 500 W @ 8Ω (500 mse ...
-
APart REVAMP2250 - page 7
Instruction manual REV AMP2250 7 • Unbalanced inputs on RCA with pass through • Input level attenuators on all inputs • 4-pole Speakon® speaker output connectors • Euroblock speaker output connectors • Extended speaker and amp protection cir cuits: DC protect, over current pr otect, over temperature protect, input overload • Individual ...
-
APart REVAMP2250 - page 8
1 10 11 12 13 3 4 5 6 8 9 2 7 8 DIGIT AL POWER AMPLIFIER 1. Channel 2 overload led: when this led lights up, you are overloading the input. Lower the input signal immediately to prevent the amplifier fr om shutting down. 2. Channel 1 overload led: when this led lights up, you are overloading the input. Lower the input signal immediately to prevent ...
-
APart REVAMP2250 - page 9
Instruction manual REV AMP2250 9 powered up. Full details of the available settings can be found below . 6. Channel 2 speaker output on 2 pole euroblock connector . 7. Channel 1 speaker output on 2 pole euroblock connector . 8. Channel 2 speaker output on speakon connector . Pin 1+ = speaker 2 +, pin 1- = speaker 2 -. 9. Channel 1 and 2 stereo spea ...
-
APart REVAMP2250 - page 10
10 DIGIT AL POWER AMPLIFIER Operation 1. Removable rack ears for 19” rack mounting. 2. Power switch: after switching on the power , the power led will light up after approx 1 second. The limit-muted leds will light up for a few seconds to avoid excessive power on pop noise. 3. Power led 4. Channel 1 status led bar and mute switch: when the mute s ...
-
APart REVAMP2250 - page 11
Instruction manual REV AMP2250 11 • CH1 SUB – TOP CH2: frequencies below 100 Hz ar e sent to the sub channel (CH1). Frequencies above 100 Hz ar e sent to the top channel (CH2).The Filter slope (12 dB/oct or second order Butterworth characteristic) and frequency (100Hz) ar e fixed. The Audio signal from input 1 is used. • CH1 TRAFO LOAD: Use ...
-
APart REVAMP2250 - page 12
12 DIGIT AL POWER AMPLIFIER of your amplifier to drive a transformer to drive 100V speaker systems. This mode applies a highpass filter to channel 2. Filter characteristics: 12 dB/oct at 50 Hz. Butterworth characteristic. This setting increases amplifier stability when using a 100 volt transformer on output 1. • CH1 BRIDGED CH2: both amps are ...
-
APart REVAMP2250 - page 13
Instruction manual REV AMP2250 13 !!! IMPORT ANT !!! This amplifier relies on convectional cooling only . In normal situations, overheating will not occur due to the class D amplifier topology . Since there are no cooling fans in the amplifier , make sure the convectional cooling system can work pr operly . The unit can be built in a 19 inch rac ...
-
APart REVAMP2250 - page 14
14 DIGIT AL POWER AMPLIFIER 110 V AC operation: it is possible to operate the unit at 110 (115) V AC. Therefor e, open the unit and set a wire jumper on the connector for 110 V AC operation. ...
-
APart REVAMP2250 - page 15
Instruction manual REV AMP2250 15 T echnical specifications Dynamic output power 2 x 350 W @ 4 Ω Sine wave power per channel 250 W @ 4 Ω (500 msec) Dynamic output power bridged 700 W @ 8 Ω Sine wave power bridged 500 W @ 8 Ω Minimum output load impedance CH1 and CH2 4 Ω Minimum output load impedance bridge mode 8 Ω Input connections 2 ...
-
APart REVAMP2250 - page 16
16 DIGIT AL POWER AMPLIFIER Cooling convectional Max power consumption 600 W Operating temperature range 0 to 40°C Mains operating voltage 230 V AC / 50 - 60 Hz (115V AC with internal jumper) Dimensions 483 x 44 x 235 mm ( including rack ears) Net weight 3.1 kg Gross weight 4.9 kg ...
-
APart REVAMP2250 - page 17
Instruction manual REV AMP2250 17 ...
-
APart REVAMP2250 - page 18
18 DIGIT AL POWER AMPLIFIER ...
-
APart REVAMP2250 - page 19
...
-
APart REVAMP2250 - page 20
developed by Audioprof nv Industriepark Brechtsebaan 8 bus 1 2900 Schoten - Belgium Company names, product names and trademarks ar e property of their respective owners. Apart-Audio specifications are subject to change without notice. ...
¿Tienes una pregunta acerca de APart REVAMP2250?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con APart REVAMP2250, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con APart REVAMP2250 probablemente compartirá una forma de solucionarlo.