-
Rimage CDPR11 - page 1
Rimage Prism Plus! TM User Guide ...
-
Rimage CDPR11 - page 2
...
-
Rimage CDPR11 - page 3
Corporate Headquarters: Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA 800 553 8312 (toll free US) Service: +1 952 946 0004 (International) Fax: +1 952 944 6956 European Headquarters: Rimage Eur ope GmbH Hans-Böckler-Straße 7 63128 Dietzenba ch, Germ any Tel: +49-(0) 6074-8521-0 Fax: +49-(0) 6074-8521-21 DISC and DVD Re ...
-
Rimage CDPR11 - page 4
Rimage PrismPlus! Support information US, Asia/Pacific, Mexico/Latin America Europe Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA Attn: Rimage Services Service: North America: 800-553 -8 312 Asia/Pacific, Mexico/ Latin America: 952-946-0004 FAX: 952-946-6956 Rimage Support Website http://www.rimage.com/support.html selec ...
-
Rimage CDPR11 - page 5
Contents Contents Introduction ...................................................................................... 1 Operating system requirements ............................................................................ 1 Media requirements ............................................................................................... 1 Ribb ...
-
Rimage CDPR11 - page 6
Rimage PrismPlus! . ii ...
-
Rimage CDPR11 - page 7
Introduction Introduction This manual provides the information ne eded to set up, install, and operate the Prism Plus printer and to identify the parts. Operating system requirements The Rimage Prism Plus is compatible only with Windows 200 0, Windows XP, and Windows 2003 Server. It requires one USB port. Media requirements You must use discs that ...
-
Rimage CDPR11 - page 8
Rimage PrismPlus! 2 110635_G Identify the parts of the Prism Plus Front view Ribbon Guides Clamping Pins Drawer and Centering Pin Supply Roller Take-u p Rolle r Control panel There are four LEDs and an Operator Button on t he operator panel located o n the front of the printer. Disc Not Present LED Active LED Power LED ...
-
Rimage CDPR11 - page 9
Identify the parts of the PrismPlus Operator button This button opens and close s the printe r tray. There is a yellow LED in the center of this button. LED indicators The LED conditions descri bed bel ow reflect conditions on a Standalone Prism Plus . Prism Plus printers that are mounted in automated equipme n t have different conditions. For cond ...
-
Rimage CDPR11 - page 10
Rimage PrismPlus! 4 110635_G Rear view ...
-
Rimage CDPR11 - page 11
Operate the PrismPlus Operate the Prism Plus Setting up a standalone Prism Plus Use these procedures to step up a standalone Prism Plus printer. Connecting the cables 1. Connect the parallel cable to the parallel cable connecti on at the back of the printer. 2. Connect the other end of the parallel cable to a parallel port on the back of the PC. 3. ...
-
Rimage CDPR11 - page 12
Rimage PrismPlus! 6 110635_G computer is connected to a network, a Local or Network Printe r dialog Play printer checkbox. splays. g. lect USB . h. Select Next . The Select manufacturer and model dialog displays. Installing the software To install CD Designer, place the CD De sign er disc in your PC disc tray and follo w the prompts. Installing ...
-
Rimage CDPR11 - page 13
Operate the PrismPlus 3. Select the printer driver file. a. Select Have Disk . The Install From Disk dialog opens. b. Select Browse . c. Navigate to the software CD included with your p rin ter. d. On the software CD, navigate: Printer Drivers > Prism > win2k_xp . e. Select the ccd2kxp.inf file. f. Select Open . g. Select OK . Rimage Perfect ...
-
Rimage CDPR11 - page 14
Rimage PrismPlus! 8 110635_G Powering on the printer 1. To power on the printer press the po wer sw it c h on the rear of the printer. The printer initializes. 2. To power off the printer press the po wer sw it c h again. ...
-
Rimage CDPR11 - page 15
Operate the PrismPlus Loading the discs 1. To open the printer tray, press the Operator bu tton . 2. Place one disc on the rubber pad between the two cl amping pi ns and the centering pin. - Important! Place the disc with the reco rding si de facing down. The reco rdi ng side has a stacking ring close to the hub t hat you can feel with your fingers ...
-
Rimage CDPR11 - page 16
Rimage PrismPlus! 10 110635_G Setting ribbon type, media type, and print strobe 1. Navigate to printing properties . 2. Select the Device Settings tab. 3. Select the type of Installed Ribbon . Note: Double Print is a feature that allows you to print the same lab el twice on the disc. Different types and brands of media hav e different printing ...
-
Rimage CDPR11 - page 17
Operate the PrismPlus Printing in color 1. Install a multicolor ribbon in the printer. 2. Navigate to printing properties . 3. Select the Device Settings tab. 4. Select the Installed Ribbon setting. 5. Select Color, Three Panel CMY from the drop-down list. Note: The Double Print selection is disabled when a color ribbon is sel ecte d because do ...
-
Rimage CDPR11 - page 18
Rimage PrismPlus! 12 110635_G Centering the image on the disc There are two ways to center the label. If the pr inter has a microparallel cable co nnection, and you have the Rimage serial cable, you can prog ram the offsets. If you do not have the serial cable, you can adjust the print position by changi ng the top and bottom margins. 1. In the CD ...
-
Rimage CDPR11 - page 19
Maintain the PrismPlus Maintain the Prism Plus General cleaning Cleaning the exterior Wipe the exterior of the printer with a lint free cloth. Cleaning the printhead Clean the printhead at every ribbon cha nge, or mo re often if streaks start appearing or the ri bb on has torn. This procedure require s the Prism Plus cleaning kit (PN 210555-00 1). ...
-
Rimage CDPR11 - page 20
Rimage PrismPlus! 14 110635_G d. To close the tray and start the cleaning cycle, pre ss th e Operator button . When the cleaning cycle is complete , the tray opens. e. If necessary, repeat step d. f. Remove the cleaning pad w ith attached disc . g. Using a cotton s wab soaked in the clea ning solution, clean the front two ribbon guides. 4. Prepare ...
-
Rimage CDPR11 - page 21
Maintain the PrismPlus Replace consumables Changing the print ribbon # Tip: If ribbons are stored in an environ ment much diffe rent from that of the printer, allow plenty of time for them to become acclimated to the new environme nt. Allow more time for greater temperature and/or humidity differences. Store the ribbons at -5 ° C (23 ° F) to 40 ? ...
-
Rimage CDPR11 - page 22
Rimage PrismPlus! 16 110635_G f. Install the supply roller as shown. Leave some slack in the ribbon le ade r. g. Press the operator button until the printer tray comes out. The ribbon is threaded to the front of the Prism Plus . h. Remove the tape from the printer tray . i. Remove the adhesive strip from the ribbon leader . 3. Load the take-up roll ...
-
Rimage CDPR11 - page 23
Maintain the PrismPlus f. Install the take-up roller in the Prism Plus and press down firmly until the take-up roller snaps into place. - Important! Do not roll the STOP - Wind Leader Onto Take -up Core Stopping here marking on the Ribbon Leader onto the t ake-up roller. The ma rkin g should not be past the point shown in the picture on page 16 . I ...
-
Rimage CDPR11 - page 24
Rimage PrismPlus! 18 110635_G Learn more Prism Plus printer specifications Item Description Printing Speed 0.65 inches/second @ 300 x 300 dpi, typical 0.45 inches/second @ 300 x 600 dpi, typical Printing Direction Images are printed from a top to bottom orientation as the media is moving out of the machine. Printing Modes Single-pass (standard) and ...
-
Rimage CDPR11 - page 25
Learn more Safety information This manual and the indications on the prod uct allo w proper and safe operation. The indication marks below help protect you and other person s from injury, and equipment from damage. n Warning! According to ANSI (American National St andards Institute) stan dards, a warning is used to indicate situations that could r ...
-
Rimage CDPR11 - page 26
Rimage PrismPlus! 20 110635_G Safety testing Product name: Prism Plus Printer Model: cdprs Notice for USA Tested to Comply with FCC Standards FO R HOME OR OFFICE USE. NOTE: This equipment has been tested and f ound to comply with the limits for a Class B digital device, pursuant to Part 15 of the F CC Rules. T hese limits are d esigned to provide r ...
-
Rimage CDPR11 - page 27
Learn more Rimage Prism Plus! TM Limited 6 Month Warranty . Rimage warrants, to the origi nal end user only , most parts of the Prism Plus! TM DISC Printer for 6 months, according to the following terms: • Rimage will replace or repair, at Rimage' s di scretion, any non-consumable parts foun d d efective within the Warranty period. • Valid ...
¿Tienes una pregunta acerca de Rimage CDPR11?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Rimage CDPR11, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Rimage CDPR11 probablemente compartirá una forma de solucionarlo.