-
Audiovox AS 9075 - page 1
Model AS 9075 Installation Manual Remote Start Upgrade Module Installation Instructions This Unit Is Intended For Installation In V ehicles With 12 V olt Negative Ground Electrical Systems, Gasoline or Diesel With T rue T ach Reference And Automatic T ransmissions Only . Kit Contents AS-9075 Control Module (1) - Multi Pin Input/Output Harness (1) - ...
-
Audiovox AS 9075 - page 2
The AS-9075 Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug preheat which may be required for certain diesel vehicles, (see selectable feature #5). If the diesel engine has a instant fire, (no glow plug pr ...
-
Audiovox AS 9075 - page 3
Remote Start Connection WIRING THE 6 PIN MAIN POWER HARNESS: RED w/ WHITE Trace Wire: + 12 volts Battery 1 Source Connect this wire t oa+1 2V D C constant source found at the vehicle's ignition switch using the 30 Amp fuse and holder provided. This wire provides power for the control circuit as well as the ignition 1 and ignition 2 relays. RED ...
-
Audiovox AS 9075 - page 4
BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the to the "ON" or "RUN" and the "ST ART" or CRANK" positions, and will have 0 volts when the key is turned to the "OFF" and "ACCESSORY&quo ...
-
Audiovox AS 9075 - page 5
the Black w/ White wire is at open circuit through the control switch, the remote starter is disabled. Connect the Black w/ White tracer wire to one of the wires from the back of the previously mounted control switch. Connect the remaining wire of the control switch to chassis ground. Always try to mount the switch so that the ON position is in an ...
-
Audiovox AS 9075 - page 6
This wire should be connected to the ignition input of the alarm system. The Yellow w/ Black wire output will allow you to remote start the vehicle while leaving the alarm armed, and to lock/ unlock the doors while running under control of the remote start unit. (2) WHITE Wires: Parking Light Flasher These wires are the COMMON and NORMALLY OPEN con ...
-
Audiovox AS 9075 - page 7
NOTE: These wires are typically White w/ Black trace and Violet w/ Y ellow trace, however in later model Cadillacs, they are run through an orange sleeve, and are either both Black, both Y ellow , or both White wires. Consult the factory service manual for additional information. 3. Connect the Light Blue Wire from the Remote S tart Unit to termina ...
-
Audiovox AS 9075 - page 8
8 WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote Start unit's operation. Understanding these outputs and the time in which they occur will allow you to determine if they are needed for the particular vehicle y ...
-
Audiovox AS 9075 - page 9
9 NOTE: 1) When selecting Diesel operation, (Feature Five), over gasoline, the only change is to the ignition 1 circuit. When Diesel is selected, the ignition 1 circuit will power up 10 seconds before the start circuit. The intent of this feature is to allow the glow plug warming required by some diesel engines. If your vehicle is a instant start d ...
-
Audiovox AS 9075 - page 10
10 The parking lights will flash a number of times indicating the reason for the last remote start shutdown. The light flash indications are as follows: 1 Flash 1 0 or 1 5 Minute Run Timer Expired 2 Flashes L ow o r N o Tach Signal (RPM) 3 Flashes Positive Or Negative Shutdown Wire Activated 4 Flashes Control Switch Moved to Off Position 5 Flashes ...
-
Audiovox AS 9075 - page 11
11 TESTING YOUR INST ALLA TION: CAUTION!! The following procedure must be performed after the installation of an Audiovox Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both. HOOD PIN SAFETY SHUT ...
-
Audiovox AS 9075 - page 12
ignition switch side of the Neutral Start Switch. If the vehicle you are working on does not have an Electrical Neutral Safety Switch, i t will be necessary to reconfigure the Remote Starts Wiring to accommodate this vehicle. T he information concerning t he Mechanical Neutral Safety Switch provided below will help you to determine if the vehicle y ...
-
Audiovox AS 9075 - page 13
margin of safety and will prevent the vehicle with a Mechanical Neutral S tart Switch from starting in gear . AUDIOVOX ADVISES THA T YOU MAINT AIN THE F ACTORY CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available. NOTE: When completing an installation using either of the following key in senso ...
-
Audiovox AS 9075 - page 14
METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A . Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B . Cut this wire and connect the ignition cylinder side to chassis ground. C . Locate the key in sensor switch wire that connects the chime module to the ignition cylinder . D. ...
-
Audiovox AS 9075 - page 15
WIRING THE CONTROL MODULE 15 © 1998 Audiovox Corp., Hauppauge, N.Y . 1 1788 Form No. 128-5365A 2nd White ...
¿Tienes una pregunta acerca de Audiovox AS 9075?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Audiovox AS 9075, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Audiovox AS 9075 probablemente compartirá una forma de solucionarlo.