-
HiRO H50083 - page 1
1 H50003 / H50083 User ’ s Manual ...
-
HiRO H50083 - page 2
2 Inst allation Guide Installation Guide for W indows 2000, W indows XP Home / Professional, XP Professional x64 Edition, V ista 32 / 64 Families, W indows 7 32 / 64 Families, and W indows Server 2003, 2008 R2 64-bit...................................... 3 System Requ irem ents ....................................................................... ...
-
HiRO H50083 - page 3
3 Installation Guide for Windows 2000, Windows XP Home / Professional, XP Professional x64 Edition, Vista 32 / 64 Families, Windows 7 32 / 64 Families, and Windows Server 2003, 2008 R2 64-bit System Requirement s Computer with Pentium 20 0 MMX or higher processor. Windows 2000, Windows XP Home / Professi onal, XP Professional x64 Edition, V ...
-
HiRO H50083 - page 4
4 For Windows 2000/XP/2003 User: As Windows starts, it will detect a new hardware has been plugged or added, and start the " Add New Hardware Wizard / Found New Hardware Wizard " . Click on " Cancel " . For Windows Vista/Win7/2008 User: As Windows starts, the following will appear on screen. 9. Please insert the analog Modem co ...
-
HiRO H50083 - page 5
5 13. Please select " Install Driver " . ...
-
HiRO H50083 - page 6
6 14. Click " OK " . (For Windows Vista/2008/7 User only) 15. Click " Install " . (For Windows Vista/2008/7 User only ) ...
-
HiRO H50083 - page 7
7 16. Click " OK " . (For Windows Vista/2008/7 User only) If you can not perform these procedures smoot hly as above, please perform the file directly: CD:Autorun.exe ...
-
HiRO H50083 - page 8
8 Basic AT Command Guide T - Set Tone Dial Default This command forces DTMF dialing until the next P dial modifier or P command is received. The modem will set an S-Parameter bit to indicate that all subsequent dialing should be conducted in tone mode. Note that the DP command will override this command. Clears S14 bit 5. This command may not be pe ...
-
HiRO H50083 - page 9
9 H - Disconnect (Hang-Up) This command initiates a hang up sequence. This command may not be available for some countries due to PTT restrictions. Syntax H[<value>] Defined Values <value> Decimal number correspo nding to the selected option. 0 The modem will release the li ne if the modem is currently on-line. 1 If on-hook, the modem w ...
-
HiRO H50083 - page 10
10 L - Speaker Volume This command sets the speaker volume contro l according to the parameter supplied. Syntax L[<value>] Defined Values <value> Decimal number correspo nding to the selected option. 0 Low speaker volume. 1 Low speaker volume. (Default.) 2 Medium speaker volume. 3 High speaker volume. Result Codes OK <value> = 0 t ...
-
HiRO H50083 - page 11
11 &V - Display Current Confi guration and Stored Profile This command reports the current (active) co nfiguration and the stor ed (user) profiles. Syntax &V Result Code OK Example: AT&V ACTIVE PROFILE: E1 L1 M1 Q0 T V1 X0 &C1 &D2 &G0 &T0 S00:000 S01:000 S02:043 S03: 013 S04:010 S05:008 S06:004 S07:050 S08:004 S10:014 S1 ...
-
HiRO H50083 - page 12
12 *B - Display Blacklisted Numbers This command requests the modem to return a list of blacklisted num bers to the DTE. The format of the response is shown by the example below. Perm anently forbidden numbers as defined by country requirements will not appear on this list. If no numbers are blacklisted, only the OK result code is issued. Example: ...
-
HiRO H50083 - page 13
13 V.92 +P and –Q Commands This section describes the +P (PCM DCE) and –Q commands and parameters used to control the V.92 Mode operation. +PCW - Call Waiting Enable This command controls the operation of the modem in the presence of call waiting. Syntax +PCW=<value> Defined Values <value> Decimal number corresponding to the selecte ...
-
HiRO H50083 - page 14
14 +PMH - Modem-on-Hold Enable This command controls the selection of modem-on-hol d in the modem. The action of the modem in response to modem-on-hold events is determined by t he state of this command as well as the state of a negotiated handshake with a V.92-co mpliant server in V.92 Mode. Syntax +PMH=<value> Defined Values <value> D ...
-
HiRO H50083 - page 15
15 +PMHT – Modem-on-Hold Timer This command controls whether or not the m odem will grant or deny a modem-on-hold (MOH) request as well as setting the MOH Timeout value. Syntax +PMHT=<value> Defined Values <value> Decimal number corresp onding to selected setting. 0 Deny V.92 modem-on-hol d Request (Default.) 1 Grant MOH with 10 secon ...
-
HiRO H50083 - page 16
16 Troubleshooting This appendix contains inf ormation that will help you to solve some of the comm on problems you might encounter , while using this 56Kbps P CI modem. For further assist ance, contact your dealer . Modem does not respond to A T commands There may be a COM port/IRQ conflict. Re conf igure the modem COM port address and IRQ lin ...
¿Tienes una pregunta acerca de HiRO H50083?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con HiRO H50083, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con HiRO H50083 probablemente compartirá una forma de solucionarlo.