Manual de instrucciones CDA SG120

36 de páginas No relevante
Descargar

Pasar a la página of 36

Summary
  • CDA SG120 - page 1

    Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www .cda.eu sg120 .. Built-in Gas Ovens Manual for Installation, Use and Maintenance GB ...

  • CDA SG120 - page 2

    2 Impor tant This appliance is designed and manufactured solely for the c ook ing of domestic (household) food and is not suitable for any non domestic application and ther efore should not be used in a commercial en vironment. The appliance guarantee will be void if the appliance is used within a non domestic environmen t i.e. a semi commercial, c ...

  • CDA SG120 - page 3

    3 IMPORT ANT SAFETY PRECA UTIONS AND REC OMMENDA TIONS IMPORT ANT : This appliance is designed and manufactured solely for the c ook ing of domestic (household) food and is not suitable for an y non domestic application and theref ore should not be used in a commercial en vironment . The applianc e guarantee will be v oid if the appliance is used w ...

  • CDA SG120 - page 4

    4 • Do not use a steam cleaner because the moisture can get into the appliance thus make it unsafe . • Do not touch the appliance with wet or damp hands (or feet). • Do not use the appliance whilst in barefoot. • I f you should decide not t o use this appliance any longer (or decide to substitute another model), bef ore disposin ...

  • CDA SG120 - page 5

    5 • W ARNING: W hen correctly installed, your pr oduc t meets all safety requir ements laid down for this type of product category . However special care should be taken ar ound the rear or the underneath of the appliance as these areas ar e not designed or intended to be touched and may c ontain sharp or rough edges, that ma y cause injur y . ...

  • CDA SG120 - page 6

    6 Con trol Panel Contr ols Description 1. Gas oven/gas grill control knob 2. 60’ alarm 3. Oven light / fan motor control knob Notes: − The electric ignition is incorporated in the thermostat contr ol k nob. − The appliance has a safety valve sy stem tted, the ow of gas will be stopped if and when the ame should accidentally go out. C ...

  • CDA SG120 - page 7

    7 F an Oven T echnical Fea tures The oven is furnished complet ely clean. It is advisable however , upon rst use, t o turn the oven on to the maximum temperature t o eliminate possible traces of grease fr om the oven burner . The same operation shall be done with the gas grill. This oven is tted with: − One gas oven burner (2,70 kW ), locat ...

  • CDA SG120 - page 8

    8 How to U se the Oven IMPORT ANT NOTES: − Do not use the appliance in case of power failur e or if the cooling fan motor is damaged. The appliance may o verheat and get damaged due to the non-operation of the cooling fan motor . − In case of failure of the cooling fan motor during the operation of the gas ov en or grill, the oven or grill burn ...

  • CDA SG120 - page 9

    9 Lighting of Oven Burner IMPORT ANT: The oven door must be open during this opera tion. T o ignite the oven burner: 1 Fully open the o ven door .  If this operation is not performed you should not proceed to ligh t the oven. 2. Press the thermostat knob throughly to start up the electric ignition and, keeping the knob under pres - sure turn it ...

  • CDA SG120 - page 10

    10 Lighting of Gas Grill Burner IMPORT ANT: The oven door must be open during this opera tion. T o light the burner , you need to: 1 Fully open the o ven door .  If this operation is not performed you should not proceed to ligh t the oven. 2 Press the thermostat knob throughly to start up the electric ignition and, keeping the knob under pressur ...

  • CDA SG120 - page 11

    11 Cooking W ith Gas O ven Before intr oducing the food, preheat the ov en to the desired temperature . For a c orrect preheating operation, it is advisable to remov e the tray from the oven and intr oduce it together with the food, when the ov en has reached the desired temperature . Check the cooking time and turn o the oven 5 minutes before t ...

  • CDA SG120 - page 12

    12 T raditional Grilling W arning: T he grill burner must be used with the door ajar only. Leav e to warm up for approximately 5 minut es with the door ajar . Place the food inside positioning the rack as near as possible t o the grill. Inser t the drip pan under the rack to collect the cooking juices. The operation of the grill should not e xceed ...

  • CDA SG120 - page 13

    13 T emperatur e recipe guide MARK APPRO X. TEMP . HEA T OF OVEN TYPE OF DISH TO C OOK 1/2 125°C 257°F V er y cool oven Meringue cakes, slow cooking items. 1 140°C 275°F Cool oven Milk puddings, very rich fruit cakes, i.e., Christmas. 2 150°C 300°F Cool or slow ov en Stews, casser oles, braising, rich fruit cakes, i.e., Dundee. 3 160°C 325° ...

  • CDA SG120 - page 14

    14 55 50 45 40 35 30 25 20 15 10 5 0 Fig . 12 Minute Coun ter 60’ Timer The minute counter is a timed ac oustic warning device which can be set for a maximum of 60 minutes. The knob (Fig. 10) must be r otated clockwise as far as the 60 minute position and then set to the required time by r otating it anticlockwise. IMPORT ANT WARNING: This is onl ...

  • CDA SG120 - page 15

    15 Care and Main tenance It is advisable to clean when the appliance is cold and especially for cleaning the enamelled parts. Avoid lea ving alk aline or acidic substances (lemon juice , vinegar, et c.) on the surfaces. Avoid using cleaning pr oducts with a chlorine or acidic base. W ARNING When correctly installed, y our product meets all safety r ...

  • CDA SG120 - page 16

    16 Replacing the Oven Lamp W ARNING: Ensure the appliance is switched o befor e replacing the lamp to av oid the possibility of elec tric shock. − Let the oven ca vity and the heating elements to cool down. − Switch o the electrical supply . − Remove the protective c over “ A ” (g. 13). − Unscrew and replace the bulb “ B ” ...

  • CDA SG120 - page 17

    17 B A C A B C Fig . 17 Fig . 18 Fig . 19 Fig . 20 Fig . 16 Oven Door Removing the Oven Door T ake care , the oven door is heavy. If you ha ve any doubts, do not attempt to remo ve the door . The oven door can easily be r emoved as follows: − Open the door to the full extent (g. 17). − Open the lever A completely on the left and right hinges ...

  • CDA SG120 - page 18

    18 Retting the Oven Door − Hold the door rmly (g. 21). − Inser t the hinge tongues into the slots , making sure that the groov e drops into place as shown in the g. 22. − Open the door to its full extent. − F ully close the levers “ A ” on the left and right hinges, as shown in the gure g . 23. − Close the door and c ...

  • CDA SG120 - page 19

    19 Removing the Inner Pane of Glass The oven door is tted with no . 2 panes: − no. 1 outside; − no. 1 inner . T o clean all panes on both sides it is necessar y to remove the inner pane as f ollows: 1. Lock the door open: − Open the door to the full extent (fig. 24). − Open the lever A completely on the left and right hinges (fig. 25). ? ...

  • CDA SG120 - page 20

    20 After Cleaning, Replac e the Inner Glass Pane When replacing the inner glass pane, make sur e that: − Y ou replace the pane correctly , as shown. T he pane must be in the position described below in order to t into the door and t o ensure that the oven operat es safely and correctly. − Y ou take ex tra care not to bump the edges of the gl ...

  • CDA SG120 - page 21

    21 Do ’ s and do not ’ s − Do always grill with the ov en door ajar . − Do read the user instructions carefully before using the o ven for rst time. − Do allow the oven to heat f or about two hours, before using f or the rst time, in order to expel any smell from the new oven insulation, without the in troduction of food. − Do cle ...

  • CDA SG120 - page 22

    22 Advic e for the Installer Appliance installation and maint enance must only be carried out by QUALIFIED TECHNICIANS and in compliance with the local safety standards . − F ailure to observe this rule will invalidate the warranty . − Always disconnect the appliance from the electrical supply befor e carr ying out any maintenance operations or ...

  • CDA SG120 - page 23

    23 Impor tant Ensure that air can ow freely around the housing area. F ailure to allow adequate ventilation to the appliance ma y result in over hea ting or damage to adjacent units. Lift the oven carefully into position on the shelf , tak ing care NOT to lift it by the door handle . If you lower the ov en door , you will see 4 screw holes, 2 on ...

  • CDA SG120 - page 24

    24 Fixing the Ov en Introduce the oven int o the furniture opening and x it with 4 screws (not supplied) as gure 33. It is essential that the oven rests on a surface which will support its weight, as the screw xing is only complementary. Adjust the hinges of furniture doors adjacent t o the oven to allow a 4-5 mm gap between the furnitur e ...

  • CDA SG120 - page 25

    25 Pro vision for V entilation – The appliance should be installed into a room or space with an air supply in accordanc e with BS 5440- 2: 2000. – F or rooms with a volume of less than 5m 3 - permanent ventilation of 100cm 2 free area will be requir ed. – F or rooms with a volume of between 5m 3 and 10m 3 a permanent ventilation of 50cm 2 fre ...

  • CDA SG120 - page 26

    26 Gas Installation Important Note This appliance is supplied for use on NA TURAL GAS or LPG (check the gas regulation label attached on the appliance). – Appliances supplied for use on NA TURAL GAS: they are adjusted f or this gas only and cannot be used on any other gas (LPG) without modication. The appliances are manufactured f or conversio ...

  • CDA SG120 - page 27

    27 Gas Connection The installation of the gas appliance to Natur al Gas or LP G as must be carried out by a suitably qualied and register ed installer. Installers shall take due acc ount of the provisions of the relevant British Standards C ode of Practice, the Gas Safety Regulations and the Building Standar ds (Scotland) (Consolidation) Regulat ...

  • CDA SG120 - page 28

    28 OK Interpose the supplied gasket. Important ! Use two wrenches t o tighten the connection. L OCK L OCK Arrow Important ! Use two wrenches to tighten the connection. Note: take care not to o vertighten the conical adaptor , as doing so may crack the test point adaptor . Rc 1/2 conical (ISO 7-1) female Rc 1/2 conical (ISO 7-1) female R 1/2 conical ...

  • CDA SG120 - page 29

    29 Maintenance and Con version t o Natural Gas or to LPG IMPORT ANT: All intervention r egarding installation maintenance and c onversion of the appliance must be fullled with original factor y parts. The manufacturer declines any liability resulting fr om the non- compliance of this obliga tion. T able for the Choice of the Injectors GB Cat: II ...

  • CDA SG120 - page 30

    30 Operations to Be Ex ecuted for the Replacement of the Injectors of the Oven and Grill Burners Some models are provided with a set of injectors for the various types of gas. If the injectors are not supplied they can be obtained from the “Ser vice Cen tre” . Select the injec tors to be replac ed according to the “ T able for the choice of t ...

  • CDA SG120 - page 31

    31 Grill Burner − Unscrew and remov e the burner securing screw “ A ” (g. 42). − Withdraw the burner as sho wn in gure 43. T ake care not to damage the safety valve pr obe and the electric ignition electrode. − Using a 7 mm box spanner , unscrew the injector (indicated by the arrow in g. 43) and r eplace it with a new one selecte ...

  • CDA SG120 - page 32

    32 Regulation of Air Supply to Oven and Grill Burners T o regulate the air supply it is necessary to remove the burners from their housings (gs. 41 - 43). − Using a cross-head screw driver , slacken the screws “ A ” securing the air ow regulation collar “ B ” (g. 44) and move the collar f or ward or backward to increase or r educ ...

  • CDA SG120 - page 33

    33 Flame faulty in primary air Flame correct Flame with ex cess primary air ong, yello w and trembling clear interior blue cone short and sharp too blue interior cone tending to detach CAUSE air regulating tube, too closed correct distance of the tube air regulating tube, too open Adjustment of the Ov en Burner Minimum This needs to be done only ...

  • CDA SG120 - page 34

    34 Mains Elec tricity Connection Incorrect installation may be dangerous and the manufacturer can not be held responsible. W arning! T his appliance must be earthed. T he manufac turer declines all responsibility for an y problem caused by failure to observe this rule . THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPL Y BY A COMPETENT PERSON, US ...

  • CDA SG120 - page 35

    35 Appliance Servicing CDA pro vide a quality and eective after-sales ser vice to cov er all your ser vicing needs. Please attach your r eceipt to this page for safekeeping . Please help us to help you b y having the following information a vailable when book ing a service -call: 1. Model type, make and model – see the product data plate. 2. E ...

  • CDA SG120 - page 36

    Please contact our Customer Care Department, or for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www .cda.eu Cod. 1104651 - ß2 ...

Fabricante CDA Categoría Oven

Los documentos del dispositivo CDA SG120 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos CDA
- manuales de instrucciones SG120
- hojas de producto CDA
- folletos informativos
- o etiquetas energéticas CDA SG120
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones CDA SG120.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje CDA SG120, instrucciones de servicio, instrucciones cortas o instrucciones de usuario CDA SG120. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto CDA SG120.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo CDA SG120, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar CDA SG120. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de CDA SG120.

El manual de instrucciones completo de CDA debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual CDA SG120 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice CDA SG120, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de CDA SG120 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo CDA SG120 - que deben facilitarnos los primeros pasos durante el uso de CDA SG120
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con CDA SG120
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de CDA SG120 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de CDA SG120?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con CDA SG120, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con CDA SG120 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Comentarios (0)