-
JVC V1700CG - page 1
INSTRUCTIONS DT -V1700CG MUL TI-FORMA T MONIT OR VOLUME SLOT 1 A B DEGAUSS MENU BLUE CHECK ASPECT AREA MARKER UNDER SCAN PULSE CROSS COLOR OFF SLOT 2 C D SLOT 3 POWER E F INPUT SELECT For Customer Use: Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference. Model No. : DT -V1700CG Serial ...
-
JVC V1700CG - page 2
SCREEN BURN ● It is not recommended to keep a certain still image displayed on screen for a long time as well as displaying extremely bright images on screen. This may cause a burning (sticking) phenomenon on the screen of cathode-ray tube. This problem does not occur as far as displaying normal video playback motion images. 䡵 PRECAUTIONS ● U ...
-
JVC V1700CG - page 3
ENGLISH 3 Fuse POWER CONNECTION The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 230 V (For European countries or United Kingdom), the power cord attached conforms to the following power supply voltage and countries. Use only the power cord designated to ensure Safety and EMC regulations of each countr ...
-
JVC V1700CG - page 4
CONTROLS AND FEA TURES FRONT VIEW <Front Panel> T ally lamp Lights when the tally control signal is ON. The tally control signal is input through the MAKE remote terminal. For details, refer to Page 17. PHASE adjustment knob Adjusts picture hue. T urn the knob to the left to make the picture redder , and turn it to the right to make the pictu ...
-
JVC V1700CG - page 5
ENGLISH REAR/SIDE VIEW <Rear Panel> COLOR OFF button/lamp Press the COLOR OFF button. The button lights and the screen becomes monochrome. When the COLOR OFF button is pressed while lit, the light goes off and the normal screen is restored. Use this function to confirm the noise in the brightness signal or to confirm the white balance. NOTE: ...
-
JVC V1700CG - page 6
Video input/output terminals Input (IN) and output (OUT) terminals for component (colour deference) or RGB signals. The IN and OUT terminals are bridge-connected. (When no cable is connected to the OUT terminal, the input signal is automatically terminated.) Select component signal : press INPUT SELECT A/C/E button Select RGB signal : press INPUT S ...
-
JVC V1700CG - page 7
ENGLISH 䡵 SDI INPUT CARD (OPTIONAL: IF-C01SDG) AUDIO 2 AUDIO 1 OUT IN SWITCHED OUT SDI 1 SDI 2 IN IN 1 2 3 4 Output terminal for a selected component serial digital signal Output terminal for s selected digital signal (the input displayed on the screen). The output signal is cable- compensated. NOTE: When the monitor ’s power is OFF , no digita ...
-
JVC V1700CG - page 8
PREP ARA TION 1. Turn of f the Multi-Format Monitor ’ s main power and unplug the power cable from the AC outlet. 2. Unscrew the screws and remove the slot cover from the slot (on the rear side of the monitor) in which you are going to install the card. 3. Insert the Input Card ’ s board (green- coloured) into the slot, fitting the board into t ...
-
JVC V1700CG - page 9
ENGLISH BASIC MENU OPERA TIONS (MAIN MENU, SETUP MENU) 䡵 ABOUT MENU SCREENS This monitor features a MAIN MENU (main menu screen) and a SETUP MENU (setup menu screen). The MAIN MENU contains the functions normally used, and the SETUP MENU contains the settings required for initial setup. <SETUP MENU> FUNCTION SETTING PICTURE SUB ADJ. COLOR T ...
-
JVC V1700CG - page 10
HOW TO USE “MAIN MENU” 䡵 “ MAIN MENU ” ITEMS The following items appear in MAIN MENU. Items Functions Displays 1 APERTURE CONTROL Compensates the frequency characteristics of the input video signal. * 1 2 SLOT CONDITION Displays the status of the input cards installed in each of the input card slots. 3 sub menu POSITION Selects the displa ...
-
JVC V1700CG - page 11
ENGLISH 1. APERTURE CONTROL Compensates the frequency characteristics of the input video signal. Press the button to display the setting menu illustrated on the right. NOTE : APERTURE CONTROL is not displayed when the RGB signal is input. ● INPUT A/B corresponds to SLOT 1, INPUT C/D to SLOT 2, and INPUT E/F to SLOT 3. ● VIDEO-1 or VIDEO-2 shows ...
-
JVC V1700CG - page 12
Input Signal Format Standard Manual setting setting (MANUAL) NTSC, P AL, 480/60i, ITU601 480/60p, 576/50i, 575/50p ITU709 720/60p, 1080/50i, 1080/60i, ITU709 1035/60i, 1080/24pSF <COLOR MATRIX> SELECT :MANUAL R-Y PHASE :90 R/B GAIN :0.86 G-Y PHASE :244 G/B GAIN :0.30 sub menu reset EXIT: MENU ADJUST:- + SELECT: 5. AREA MARKER-R Items : Select ...
-
JVC V1700CG - page 13
ENGLISH HOW TO USE “SETUP MENU” 䡵 “ SETUP MENU ” ITEMS Items Functions 1 FUNCTION SETTING Displays the monitor’s power-up time or the total usage time. 2 PICTURE SUB ADJ. Performs approximate adjustments using the control knobs on the front panel. 3 COLOR TEMP ./BAL. Sets or adjusts the colour temperature or white balance. 4 SIZE/POSI. ...
-
JVC V1700CG - page 14
HOW TO USE “SETUP MENU” (cont'd) <FUNCTION SETTING> COLOR SYSTEM :AUTO RUSH DELAY TIME :STD. HOUR METER X100h :000 EXIT: MENU ADJUST:- + SELECT: <PICTURE SUB ADJ.> CONTRAST :00 BRIGHT :00 CHROMA :00 PHASE :00 NTSC SETUP :00 COMPO.LEVEL :SMPTE sub menu reset EXIT: MENU ADJUST:- + SELECT: 䡵 ITEM CONTENTS AND ADJUSTMENT RANGE/SE ...
-
JVC V1700CG - page 15
ENGLISH <COLOR TEMP./BAL.> COLOR TEMP. :LOW BLUE DRIVE :000 RED DRIVE :000 GREEN CUTOFF :000 BLUE CUTOFF :000 RED CUTOFF :000 sub menu reset EXIT: MENU ADJUST:- + SELECT: <SIZE/POSI. ADJ.> H.SIZE :00 H.POSITION :00 V.SIZE :00 V.POSITION :00 sub menu reset EXIT: MENU ADJUST:- + S EL E C T: 3. COLOR TEMP ./BAL. Sets or adjusts the colour ...
-
JVC V1700CG - page 16
<STATUS DISPLAY> STATUS DISPLAY :ON 1080/1035 :1080 EXIT: MENU ADJUST:- + S EL E C T: <DISTORTION ADJ.> PINCUSHION :00 PIN.BALANCE :00 PARALLELOGRAM :00 TRAPEZOID :00 sub menu reset EXIT: MENU ADJUST:- + SELECT: 5. DISTORTION ADJ. Compensates the picture distortion. Press the button to display the setting menu illustrated on the right. ...
-
JVC V1700CG - page 17
ENGLISH HOW TO USE EXTERNAL CONTROL 䡵 ABOUT EXTERNAL CONTROL This multi-format monitor has two external control terminals. One is the MAKE terminal, which controls the monitor by connecting the terminals with many functions to the ground (GND) terminal. The other is the RS-232C terminal, which allows the monitor to be controlled by a PC via seria ...
-
JVC V1700CG - page 18
HOW TO USE EXTERNAL CONTROL (cont.) 䡵 HOW T O USE THE RS-232C TERMINAL Y ou can control the monitor from your PC via the RS-232C terminal. For details on operating the monitor from the PC, consult your dealer or service centre for details. 1. Cable Prepare a straight cable with a D-sub connector (9-pin, female) and a D-sub connector (9-pin, male) ...
-
JVC V1700CG - page 19
ENGLISH Problems No power supply No picture with the power on No sound Wrong colour Unnatural picture Shaking picture Points to be checked Is the power plug loosened or disconnected? Is the signal cable disconnected? Is the power of the connected component ON? Is the signal output from the connected component? Is the input signal selected correctly ...
-
JVC V1700CG - page 20
Problems Irregular colour Wrong picture position, wrong picture size Front panel buttons and knobs do not function Points to be checked Is the monitor placed or moved close to a speaker or any other device incorporating a magnet? Has the position of the monitor been changed with the power on? Has the picture position, size or distortion been change ...
-
JVC V1700CG - page 21
ENGLISH SPECIFICA TIONS 䡲 T ype : Multi-format monitor 䡲 Picture T ube : 17" measured diagonally 䡲 Effective Screen Size : Width : 330 mm Height : 250 mm Diagonal : 410 mm 䡲 Scanning Frequency : H : 15 kHz/15 kHz – 45 kHz V : 50 Hz – 100 Hz 䡲 Video Band : Component : 25 MHz (–3 dB) Video (Y/C) : 8 MHz (–3 dB) 䡲 Horizontal R ...
-
JVC V1700CG - page 22
䡵 Compliant Signal Formats of Each Input Card Input Signals IF-C01PNG IF-C01COMG IF-C01SDG IF-C01HSDG NTSC (3.58 MHz) R —— — P AL (4.43 MHz) R —— — Black-and-White (50 Hz/60 Hz) R —— — 480/60i (525i) — RR — 480/60p (525p) — R —— 576/50i — RR — 576/50p ( * 1) — 䡬 —— 720/60p (720p) — R — R 1080/50i ( * 1) ...
-
JVC V1700CG - page 23
ENGLISH SPECIFICA TIONS (INPUT CARD: OPTIONAL) 䡵 IF-C01COMG: COMPONENT/RGB INPUT CARD T ype : Component/RGB input card for multi-format monitor Inputs/Outputs : Component (Y , P B /B-Y , P R /R-Y) or RGB: 1 line, BNC connector x 6 (Y : 1 V (p-p), 75 Ω /P B , B-Y , P R , R-Y , R, G, B: 0.7 V (p-p), 75 Ω ) Synchronised signal (HD/C S , VD) : 1 ...
-
JVC V1700CG - page 24
24 JVC PROFESSIONAL PRODUCTS COMPANY DIVISION OF US JVC CORP. 1700 Valley Road Wayne, N.J. 07470 JVC CANADA INC. 21 Finchdene Square, Scarborough Ontario M1X 1A7 © 2001 VICTOR COMP ANY OF JAP AN, LIMITED Printed in Japan LCT0971-00 2 A 0 7 01-I-U-VP DT-V1700CG MULTI FORMAT MONITOR Untitled-1 01.3.27, 9:58 24 ...
¿Tienes una pregunta acerca de JVC V1700CG?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con JVC V1700CG, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con JVC V1700CG probablemente compartirá una forma de solucionarlo.