-
CDA HVG77 - page 1
Customer Car e Department • T he Group Ltd. • Harb y Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : ww w .cda.eu HVG 77 .. - 4Q5 .. Gas on Glass Cooktops Manual for Installation, U se and Maintenance GB ...
-
CDA HVG77 - page 2
2 Impor tant This appliance is designed and manufactured solely f or the cooking of domestic (household) food and is not suitable for any non domestic application and therefor e should not be used in a commercial environment. The appliance guarantee will be v oid if the appliance is used within a non domestic environmen t i.e. a semi commercial, c ...
-
CDA HVG77 - page 3
3 Impor tant Safeguards and Rec ommendations – Do not carr y out any cleaning or maintenance without rst disc onnecting the appliance from the electrical supply. – During and after use of the hob, certain parts will become ver y hot. Do not touch hot parts. – After use always ensure tha t the control knobs are in the “ ” (o ) positi ...
-
CDA HVG77 - page 4
4 F eatures and T echnical Data 9 8 7 6 5 2 2 3 4 1 2 2 1 3 9 8 7 6 5 4 Cooking P oints 1. Auxiliary burner (A) 1,00 kW 2. Semi-rapid burner (SR) 1,75 kW 3. Rapid burner (R) 3,00 kW 4. T riple ring burner ( TR) 3,50 kW Contr ol Panel 5. Auxiliary burner control knob (1) 6. Rear right semi-rapid burner control knob (2) 7. T riple ring burner control ...
-
CDA HVG77 - page 5
5 How to U se the Hob Gas Burners Gas ow to the burners is adjusted by turning the knobs (illustrated in g. 2) which contr ol the valves. T urning the knob so that the indicator line points to the symbols printed on the panel achieves the follo wing functions: – Symbol : T ap closed (burner o ) – Symbol : High (maximum) – Symbol : Lo ...
-
CDA HVG77 - page 6
6 Choice of Burner The symbols printed on the panel by the side of the knob indicate which burner you are c ontrolling. Choose a suitable burner depending on the cookware dia - meter and capacity . The pan diameter should be suitable for the burner pow er to make the most of the burner ’ s high eciency and not waste fuel. A small pan does not ...
-
CDA HVG77 - page 7
7 Fig . 6a Fig . 6b ...
-
CDA HVG77 - page 8
8 Cleaning and Maintenanc e General Tips – Before cleaning the hob switch it o and wait f or it to cool down. – Clean with a cloth, hot water and soap or liquid detergen t. – Do not use products which are abrasive, c orrosive or chlorine based. – Do not use steel pads. – Avoid using cleaning pr oducts with a chlorine or acidic base. ? ...
-
CDA HVG77 - page 9
9 Burners and Grids – These parts can be removed and cleaned with appropriate pr oducts. – After cleaning, the burners and their ame spreaders must be w ell dried and correctly replaced. – It is very impor tant to check that the burner ame spreader and the cap have been correctly positio - ned. F ailure to do so can cause serious proble ...
-
CDA HVG77 - page 10
10 F C Flame failure probe “ T ” Ignitor “ S ” Correct P ositioning of the Auxiliary , S emi-rapid and Rapid Burners – It is very impor tant to check that the burner ame spreader “ F ” and the cap “ C ” have been correctly positioned (see gs. 8 and 9). They shall be level and must not rotate. F ailure to do so can cause seri ...
-
CDA HVG77 - page 11
11 Correct P ositioning of the T riple Ring Burner – The triple ring burner must be correctly positio - ned (see g. 11); the burner ribs must be tted in their housing as shown by the arrow . T he burner correctly positioned must not rotate (g . 12). – Then position the cap “ A ” and the ring “ B ” (gs. 12 and 13). They shall ...
-
CDA HVG77 - page 12
12 TIPS FOR INST ALLA TION Location – The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a room or space containing a bath or a show er . – The appliance must not be installed in a bed-sitting room of less than 20m 3 . – The appliance is designed and appro ved for domestic use only and should not be i ...
-
CDA HVG77 - page 13
13 Installation T echnical Information For The Installer In order to install the cooktop into the kitchen xture, a hole with the dimensions sho wn in g. 16 has to be made, bearing in mind the follo wing: – Within the unit, between the bottom of the c ooktop and the upper surface of a shelf there must be a clearance of at least 30mm. It ...
-
CDA HVG77 - page 14
14 Installing the Separator Below the Base of the Cooktop It is recommended that a 30mm clearance be left between to base of the cooktop and the separat or . The separator shall be heat r esistant, made of low thermal conductivity material and shall be remova - ble with the use of a tool for installation and ser - vice. 30 mm Space for connections ...
-
CDA HVG77 - page 15
15 F astening the C ooktop Each cooktop is provided with an installa tion kit including brackets and screws for fastening the co - oktop to benches from 30 to 40mm thick.The kit includes two “ F ” type brackets (for the front of the cooktop), two “ R ” type brackets (for the rear of the cooktop ) and four self-threading screw s “ S ” (? ...
-
CDA HVG77 - page 16
16 Gas Supply Requirements Important Note This appliance is supplied for use on NA TURAL GAS or LPG (check the gas regulation label attached on the appliance). – Appliances supplied for use on NA TURAL GAS: they are adjusted for this gas only and cannot be used on any other gas (LPG) without modication. The appliances are manufactured for con ...
-
CDA HVG77 - page 17
17 Gas Connection The installation of the gas appliance to Natur al Gas or LP Gas must be carried out by a suitably quali- ed and registered installer . I nstallers shall take due account of the provisions of the r elevant British Standards Code of P ractice, the Gas Safety Regulations and the Building Standards (Scotland) (C onsoli - dation) Re ...
-
CDA HVG77 - page 18
18 Gas Connection GB Cat: II 2H3+ The tting (g. 20) is made up of: – 1 nut “ A ” – 1 elbow tting “ C” – gasket “ F ” Connection to the Gas Supply • Be careful when exible pipes are used that they do not come into contact with moving parts. • T o maintain the thickness of 3 cm, the hob is tted with a channe ...
-
CDA HVG77 - page 19
19 Con version to Natur al Gas or to LPG Replacing the Burner Injectors If the NA TURAL GAS/LPG conversion kit is not supplied with the appliance this kit can be purchased by contacting the After-Sales Service. Choose the injectors to be replaced accor ding to the “ T able for the Choice of the Injectors” . The injector diameter , expressed in ...
-
CDA HVG77 - page 20
20 T able for the Choice of the Injectors GB Cat: II 2H3+ Burners Nominal Powe r kW Reduced Powe r kW G30 - 28-30 mbar G31 - 37 mbar G20 - 20 mbar Ø Injector 1/100 mm Ø Injector 1/100 mm Auxiliary (A) 1,00 0,30 50 72 (X) Semi-Rapid (SR) 1,75 0,45 65 97 (Z) Rapid (R) 3,00 0,75 85 115 ( Y ) T riple Ring ( TR) 3,50 1,50 95 135 ( T ) Lubrication of t ...
-
CDA HVG77 - page 21
21 Mains Elec tricity Connection Incorrect installation may be dangerous and the manufacturer can not be held responsible. W arning! This appliance must be ear thed The manufac turer declines all responsibility for any problem caused by failure to observe this rule . THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPL Y BY A COMPETENT PERSON, USING ...
-
CDA HVG77 - page 22
22 Appliance Servicing CDA provide a quality and e ective after-sales service to cover all your servicing needs. Please attach your rec eipt to this page for safekeeping . Please help us to help you by ha ving the following inf ormation available when booking a ser vice- call: 1. Model type, make and model – see the product data plate. 2. Evid ...
-
CDA HVG77 - page 23
23 ...
-
CDA HVG77 - page 24
T o contact our Customer Care Department, or for Service, please contact us on the details below . 1103862 - ß4 Customer Car e Department • T he Group Ltd. • Harb y Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : ww w .cda.eu ...
¿Tienes una pregunta acerca de CDA HVG77?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con CDA HVG77, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con CDA HVG77 probablemente compartirá una forma de solucionarlo.