-
NEC MultiSync EA190M - page 1
MultiSync EA190M User ’ s Manual ...
-
NEC MultiSync EA190M - page 2
Index W arning, Caution ............................................................................................................... .......... English-1 Registration Information ....................................................................................................... ........ English-1 Recommended use ............................. ...
-
NEC MultiSync EA190M - page 3
English English-1 W ARNING CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . T O FULL Y DISENGAGE THE POWER TO THE UNIT , PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET . DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE P ARTS INSIDE. REFER SER VICING T O QUALIFIED SERVICE PERSONNEL. ...
-
NEC MultiSync EA190M - page 4
English-2 Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1. Use the attached specif ...
-
NEC MultiSync EA190M - page 5
English English-3 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MUL TISYNC LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer al ...
-
NEC MultiSync EA190M - page 6
English-4 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONIT OR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Y our eyes should look slightly downward ...
-
NEC MultiSync EA190M - page 7
h s i l g n E Engl ish-5 C on t en t s Y our new N EC Mu ltiSyn c LCD moni tor bo x* sh ould c ontain the follow ing: • Mult iSync LCD m onitor with tilt /swiv el/piv ot/hei ght a djust base • Powe r Cord • Base stand • Video S ignal Cable (15- pin m ini D- SUB m ale t o 15-p in mi ni D- SUB m ale) • Video S ignal Cable (DVI -D to DVI- D) ...
-
NEC MultiSync EA190M - page 8
English-6 Quick Start To attach the Base to the LCD stand: 1. Place monitor face down on a non-abrasive surface ( Figure 1 ). NOTE: Handle with care when monitor facing down, for avoiding damage to the front control buttons. 2. Please pivot base 90 degrees as shown in Figure 1 . NOTE: Handle with care when pulling the stand. 3. Attach the base stan ...
-
NEC MultiSync EA190M - page 9
English English-7 Figure C.1 Power Button Figure RL.1 Raise and Lower Monitor Screen The monitor may be raised or lowered. T o raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height ( Figure RL.1 ). NOTE: Handle with care when raising or lowering the monitor screen. T ilt and Swivel Grasp both sides o ...
-
NEC MultiSync EA190M - page 10
English-8 Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place monitor face down on a non-abrasive surface ( Figure S.1 ). NOTE: Handle with care when monitor facing down, for avoiding damage to the front control buttons. 3. Remove the 4 screws connecting the stand to the monit ...
-
NEC MultiSync EA190M - page 11
English English-9 7. Reverse this process to re-attach stand. NOTE: Use only VESA-compatible alternative mounting method. Handle with care when removing stand. NOTE: Match “TOP SIDE” mark on stand to top side of the monitor head when re-attaching stand. Flexible Arm Installation This LCD monitor is designed for use with a flexible arm. T o moun ...
-
NEC MultiSync EA190M - page 12
English-10 Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: To access OSD menu, press any of the control buttons (MENU, Left, Right, Down, Up). To change signal input, press the SELECT button. To change ECO MODE, press the RESET/ECO MODE button. NOTE: OSD must be closed in order to change signal inpu ...
-
NEC MultiSync EA190M - page 13
English English-11 Image Controls (Analog input only) LEFT / RIGHT Controls Horizontal Image Position within the display area of the LCD. DOWN / UP Controls V ertical Image Position within the display area of the LCD. H.SIZE Adjusts the horizontal size by increasing or decreasing this setting. FINE Improves focus, clarity and image stability by inc ...
-
NEC MultiSync EA190M - page 14
English-12 OSD W arning OSD W arning menus disappear with Exit button. NO SIGNAL: This function gives a warning when there is no Horizontal or V ertical Sync. After power is turned on or when there is a change of input signal, the No Signal window will appear . OUT OF RANGE: When input signal is non-supported timing or the video signal doesn’t ha ...
-
NEC MultiSync EA190M - page 15
English English-13 Specifications Monitor Specifications MultiSync EA190M Notes LCD Module Diagonal: 48.2 cm/19.0 inches Active matrix; thin film transistor (TFT) liquid V iewable Image Size: 48.2 cm/19.0 inches crystal display (LCD); 0.294 mm dot pitch; Native Resolution (Pixel Count): 1280 x 1024 250 cd/m 2 white luminence; 900:1 contrast ratio, ...
-
NEC MultiSync EA190M - page 16
English-14 Features Thin-frame design creates more desktop space for you to work and play , while the flat screen’s crisp, bright images and crystal- clear text deliver a comfortable viewing experience. No T ouch Auto Adjust automatically adjusts your optimal image settings upon initial power-on. Colour Control System allows you to change between ...
-
NEC MultiSync EA190M - page 17
English English-15 T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display c ...
-
NEC MultiSync EA190M - page 18
English-16 TCO Displays 5.0 Congratulations! This display is designed for both you and the planet! The display you have just purchased carries the TCO Certified label. This ensures that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high perf ...
-
NEC MultiSync EA190M - page 19
English English-17 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment. W e are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent ...
¿Tienes una pregunta acerca de NEC MultiSync EA190M?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con NEC MultiSync EA190M, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con NEC MultiSync EA190M probablemente compartirá una forma de solucionarlo.