-
Makita 6041DW - page 1
Cordless Drill Capacities Steel /Wood Wood screw 10 mm (3/8”) MODEL 6041D 10 mm (3/8”) MODEL 6041DW Wlth Qulck Charger No load speed (RPM) INSTRUCTION MANUAL Input A.C. only 50 Hz - 60 Hz SPECIFICATIONS Model 6041D output Charging time Approx. 3 Hr. D.C. 6.4 V. Dinensions 1 Net (L x W x H) weight 10 13/8,,, mm I 4.5 mm x 20 mm I 201 mm x 48 mm ...
-
Makita 6041DW - page 2
IMPORTANT SAFETY I NSTRU CTlO N S (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. a. 9. 10. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invit ...
-
Makita 6041DW - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extens ...
-
Makita 6041DW - page 4
IMPOKlANT SAFETY INSTRUC=TIONS (FOR BATTERY CHARGER) I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battory charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of inju ...
-
Makita 6041DW - page 5
ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1. The Charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this Charger. Do not attempt to charge the tool with any other charger. 2. Do not charge the tool when temperature is BELOW 10°C (50OF) or ABOVE 45OC (113OF). 3. Do not use charg ...
-
Makita 6041DW - page 6
Charging Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. CAUTION: The battery in your new tool is not fully charged. You will need to charge it before use. Do not operate the tool during charging. Overcharging more than 2 days consider- ably shortens the battery service ...
-
Makita 6041DW - page 7
Holding tool When drilling a large diameter hole, hold the tool firmly with both hands. Switch action To start the tool, simply pull the trigger. Release the trigger to stop. Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the revers- ing switch to the right for clockwise rota- tion or to the left ...
-
Makita 6041DW - page 8
CAUTION : Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pres- sure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. -There is a tremendous force exerted on the tool/bit at the time of hole breakthrough. Hold the tool firmly and exert car ...
-
Makita 6041DW - page 9
MAINTENANCE CAUTION : Always be sure that the tool is switched off before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. DISPOSING OF TOOL A nicad battery is bu ...
-
Makita 6041DW - page 10
Recycling the battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. 2. (a) Take the battery to your nearest Makita Factory Service Center. or (b) Take the battery to your nearest Makita Authorized Service Center or Distributo ...
-
Makita 6041DW - page 11
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card Dacked with vour tool. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of a ...
-
Makita 6041DW - page 12
Jan.-14-'93 US 10 mm (318") CORDLESS DRILL Model 60410 9 Note: The switch and other part configurations may differ from country to country. 12 ...
-
Makita 6041DW - page 13
MODEL 6041D Jan.-14-'93 US 11 12 13 14 15 16 17 18 19 20 'iM ,& DESCRIPTION 1 1 1 1 1 1 1 1 1 1 'iM G&, DESCRIPTION 10 17 21 31 41 51 61 71 81 91 1 Tappmg Sum H3m Name Plate Housing Set IWith Item 151 cWmmuI* Hex -el SEW MSxZl Drill Chuck S10 Gear Plane 8eCrl"g 5 DCMolor4,L)v Switch Lever ComDre.lsm Swmg 1 Switch CllCU ...
-
Makita 6041DW - page 14
MAKVA LIMlTED ONE YEAR WARRAMY Warranty Policy Every Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted to be free of defects from worka~&p and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this onayear period, return the COMPLETE tool, freight p ...
¿Tienes una pregunta acerca de Makita 6041DW?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 6041DW, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 6041DW probablemente compartirá una forma de solucionarlo.