-
Generac 1292-2 - page 1
High Pressure W asher Owner’ s Manual This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. 230 0 PSI Model No. 1292-2 (2300 PSI High Pressure W asher) Manual No. B5715 Revision 2 (8/3/2000) Visit our Generac website: w w w ...
-
Generac 1292-2 - page 2
Generac Portable Product s 2,300 PSI High Pressure W asher 2 EQUIPMENT DESCRIPTION CONGRA TULA TIONS on your purchase of a GENERAC high pressure washer . It has been designed, engineered and manufactured to give you the best possible dependability and performance. This manual contains information for a high pressure washer that operates at 2,300 PS ...
-
Generac 1292-2 - page 3
Generac Portable Product s 2,300 PSI High Pressure W asher 3 Operate engine only at governed speed. Running the engine at excessive speeds increases the hazard of personal injury . Do Not tamper with parts which may change the governed speed. Do Not wear loose clothing, jewelry or anything that may be caught in the starter or other rotating ...
-
Generac 1292-2 - page 4
Generac Portable Product s 2,300 PSI High Pressure W asher 4 KNOW YOUR PRESSURE W ASHER Read this owner s manual and safety rules before operating your high pressure washer . Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future refere ...
-
Generac 1292-2 - page 5
Generac Portable Product s 2,300 PSI High Pressure W asher 5 W ARNING! Read entire owner s manual before you attempt to assemble or operate your new pressure washer . REMOVE PRESSURE W ASHER FROM CARTON Remove the high pressure hose and part s box included with pressure washer . Slice two corners at the end of carton from top to bottom s ...
-
Generac 1292-2 - page 6
Generac Portable Product s 2,300 PSI High Pressure W asher 6 NOTE : It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports. Insert the carriage bolts through the holes on the handle and attach the plastic knobs. T ighten the knobs by hand (Figure 3). Attach si ...
-
Generac 1292-2 - page 7
Generac Portable Product s 2,300 PSI High Pressure W asher 7 Install the fuel cap and wipe up any spilled gasoline. Connect Hose and W ater Supply to Pump IMPORT AN T : Y ou must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine. S tarting engine without all hoses connected and water supplied will d ...
-
Generac 1292-2 - page 8
Generac Portable Product s 2,300 PSI High Pressure W asher 8 Check to make sure that there are no kinks, cuts, or damage to the high pressure hose. Check that oil has been added to the proper level in the engine crankcase. Add the proper gasoline to fuel tank. Provide a proper water supply (not to exceed 140°F) at an adequate flow ...
-
Generac 1292-2 - page 9
Generac Portable Product s 2,300 PSI High Pressure W asher 9 How to Use the Adjust able Nozzle Y ou now should know how to ST ART your pressure washer and how to STOP it. The information in this section will tell you how to adjust the spray pattern and to apply detergent or other cleaning chemicals. DANGER! Never adjust spray pattern when spraying. ...
-
Generac 1292-2 - page 10
Generac Portable Product s 2,300 PSI High Pressure W asher 10 Applying Detergent with the Adjust able Nozzle IMPORT AN T : Use soaps designed specifically for pressure washers . Household detergents could damage the pump. IMPORT AN T : Y ou must attach all hoses before you start the engine. S tarting the engine without all the hoses connected and w ...
-
Generac 1292-2 - page 11
Generac Portable Product s 2,300 PSI High Pressure W asher 11 SPECIFICA TIONS Outlet Pressure 2300 psi Flow Rate 2.9 gallons per minute (gpm) Detergent Use detergent approved for pressure washers W ater Supply Not to Exceed 140°F T emperature Automatic Cool Will cycle when water Down System reaches 140°-145°F GENERAL MAINTENANCE RECOMMENDA TIONS ...
-
Generac 1292-2 - page 12
Generac Portable Product s 2,300 PSI High Pressure W asher 12 When the water supply is steady and constant, engage the safety latch. T o remove contaminant s from the pump, follow these step s: Set up the pressure washer as described in Preparing Pressure W asher For Use (page 5). Connect the water supply and turn water on. Remove ...
-
Generac 1292-2 - page 13
Use the wire included in the kit (Figure 17) or a small paper clip to free the foreign material clogging or restricting the nozzle. Remove additional debris by back flushing water through the nozzle extension (Figure 18). Back flush between 30 to 60 seconds. T urn the nozzle extension to stream spray and move the nozzle from low to high whi ...
-
Generac 1292-2 - page 14
Generac Portable Product s 2,300 PSI High Pressure W asher 14 NOTES ...
-
Generac 1292-2 - page 15
Generac Portable Product s 2,300 PSI High Pressure W asher 15 TROUBLESHOOTING Problem Ca use Corre ction Pump has following problems: failure to produc e pressure, er ratic pres sure, chattering, loss of pressur e, low wa te r v o lu me . 1. Nozzle in l ow pr essure m ode. 2. W ater inlet is blocked. 3. Inadequate water su ppl y. 4. Inlet hose is k ...
-
Generac 1292-2 - page 16
Generac Portable Product s 2,300 PSI High Pressure W asher 16 EXPLODED VIEW UNIT ...
-
Generac 1292-2 - page 17
Generac Portable Product s 2,300 PSI High Pressure W asher 17 P ARTS LIST UNIT Item Part # Qty . Description 1 AB5721 1 BASE 2 52858 8 LOCKNUT , M8 3 42909 2 HHCS, M8 1.25 x 30 4 50190 2 W ASHER, Flat .34" x 1" 5 27007 2 MOUNT , Donut T ype Vibration 7 B4099 1 DECAL, IMP . Purge Air 8 B2150 1 HOOK, Gun 9 B2516 1 CAP , Vinyl (black) 10 ...
-
Generac 1292-2 - page 18
Generac Portable Product s 2,300 PSI High Pressure W asher 18 EXPLODED VIEW PUMP 48 52 53 45 44 43 ...
-
Generac 1292-2 - page 19
Generac Portable Product s 2,300 PSI High Pressure W asher 19 P ARTS LIST PUMP Item Part # Qty Description 0 187264 0 Complete Pump Assy . 1 100B3699 1 Manifold 2 165B3169 6 O-ring 12.42 x 1.78 3 102B3699 6 V alve unit 4 103B3699 6 O-ring 5.60 x 1.78 5 104B3699 3 V alve cap 6 105B3699 1 Unloader valve screw 7 106B3699 3 O-ring 9.92 x 2.62 8 107 ...
-
Generac 1292-2 - page 20
LIMITED PRESSURE W ASHER W ARRANTY GENERAC PORT ABLE PRODUCTS (hereafter referred to as the COMP ANY) warrants to the original ret ail purchaser , the pressure washer manufactured by the COMP ANY to be free from defect s in material and workmanship for the period(s) set forth below from the date of original purchase. This warranty is not transferab ...
¿Tienes una pregunta acerca de Generac 1292-2?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Generac 1292-2, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Generac 1292-2 probablemente compartirá una forma de solucionarlo.