-
HANNspree DT07-10A1 - page 1
...
-
HANNspree DT07-10A1 - page 2
Table of Contents 1 1. Warranty and Service .................................................... 3 2. Preface .................................................................... ..... 4 3. Description of Warning Symbols ................. .................... 5 4. Safety Notices .......................................................... ..... 6 5. ...
-
HANNspree DT07-10A1 - page 3
Table of Contents 2 11. Adjusting On-Screen Display (OSD) Settings ............... 2 8 Brightness ............................................................... 2 9 Contrast ............................................................... ... 3 0 Video Setting ........................................................... 3 1 Hue ..................... ...
-
HANNspree DT07-10A1 - page 4
3 The instructions on this manual are for the model(s) listed on the front cover . Befor e you start reading, check your product number by lookin g at the rear of your TV . Thank you for purchasing our Liquid Crystal Display T elevision (LCD TV). With this product, you will be able to enjoy superior audio and video while enriching your lifes tyle w ...
-
HANNspree DT07-10A1 - page 5
4 This manual is designed to assist use rs in setting up and using t he LCD TV . Information in this document ha s been carefully checked for accuracy; however , no guarantee is given to the corr ectness of the content s. The informatio n in this document is sub ject to change without notice. Copyright © Copyright 2003 Hannspree, Inc. All rights r ...
-
HANNspree DT07-10A1 - page 6
5 Electric Power Notice Electric power may cause personal inju ry and mechanical damage if it is misused. Although safety has been tak en into conside ration during the design and production of this product, electric shock or fire can result when the product is misused. T o prevent potential danger , follow the instructions below when installing, o ...
-
HANNspree DT07-10A1 - page 7
6 Power Supply Safety Notes 1. T o avoid electric shocks, do not use an extended power cord or an outlet that does not match this pr oduct's plug or leaves the plug exposed. 2. This product has a 3-pin gro unded plug. The th ird pin connects to ground; do not r emove it. 3. If the power cord or plug is damaged or worn, unplug it immedi- ately ...
-
HANNspree DT07-10A1 - page 8
7 Before Y ou Proceed 1. Read the Safety Notices and the User ’s Manual carefully before turning the pro duct on. 2. Keep your User ’s Manual in a safe place for future refere nce. Keep the box and packaging in case the product needs to be shipped in the future. 3. Follow the product and warn ing label instructions. 4. Any changes or modificati ...
-
HANNspree DT07-10A1 - page 9
8 Optimal V iewing Dist ance C H V O L C H 102 cm ...
-
HANNspree DT07-10A1 - page 10
9 Import ant Safety Inst ructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near wa ter . 6. Clean only with a dr y cloth. 7. Do not block any ven t ilation openings. Inst a ll in accordance with th e manufacturer ’s instruct ions. 8. Do not instal l near ...
-
HANNspree DT07-10A1 - page 11
10 10. Protect the power cord from being walked on or pinched particularly at th e plug, conve- nience receptacles, and the point where they exit from the app aratus. 1 1. Use only with a cart, stand, tripod, bracket, or table specified by the manufa cturer , or sold with the apparatus. Whe n a cart is used, use caution when movi ng the cart/app ar ...
-
HANNspree DT07-10A1 - page 12
11 Personal Safety T o avoid overloading t he power supply , do not plug too many electrical devices into an outlet or extension cable. Dangerous high-volt age electric power compo- nents are lo cated inside the TV . T o avoid electric shock, do not disassemble the casing. Do not place or drop met als, small objects, or flammable materials in t he ...
-
HANNspree DT07-10A1 - page 13
12 Inst allation T o avoid damage to power circuits, do not place the TV in locations where there is excessive steam or dust. Do not place the TV on a bed, sofa, carpet, or in a sealed cabinet to avoid blocking the product's vent s. Install the outdoor antenna far from power trans- mission lines to av oid possible danger . Remove the power cor ...
-
HANNspree DT07-10A1 - page 14
13 Operation Maintenanc e This product is designed for power sources as labeled on the casing. Avoid using any other power accessories to avoid electric sho ck or other damage. The plug can be inserted into an outlet in only one direction. Notify a qualified service techni- cian if you cannot plug it in correctly . If there is any problem that cann ...
-
HANNspree DT07-10A1 - page 15
14 FCC Compliance S t atement 1 This device complies with part 15 of the FCC Rules. Operation is sub- ject to the following two conditions: (1) This device may n ot cause harm- ful interference, and ( 2) this devi ce must accept any interference received, including inter ference that may cause undesired operation. This equipment has been tested and ...
-
HANNspree DT07-10A1 - page 16
15 DOC Compliance Notice 1 This digital app aratus does not exc eed the Class B limit s for radio noise emissions from digital app aratus as set out in the Radio Interference Regulations of the Canadian Dep artment of Communications.This device complies with Canada ICES-003 Class B. CE Conformity S t atement 2 This device complies with the requirem ...
-
HANNspree DT07-10A1 - page 17
16 Thank you for purchasing this Liq- uid Crystal Display TV . Y our L CD TV is designed to be safe, versa- tile, and easy to use. The design of the product is featuring "Mickey Mouse”, which makes it a fun addition to any room. Y ou can watch broadcast or cable television channels, and easily connect a VCR, VCD or DVD player to the stand ar ...
-
HANNspree DT07-10A1 - page 18
17 Make sure the following component s are included in the box. Contact your vendor immediately if any thing is missing or damaged. TV Wire Material Package G W A 1 8 3 0 0 V 8 0 C V W - 1 E 7 7 8 7 4 Power Cord Power adapter 4-IN-1 Cable Quick Start Guide U ser's M anual RCA Jack x 3 S Jack x 1 W a r ranty and servic e m anual User ’s Manua ...
-
HANNspree DT07-10A1 - page 19
18 Fr o n t V i e w Description Function 1 Select channel Changes the channel. Press CH to increase the channel number . Press CH to decrease the channel number . 2 Adjust volume Press VOL+ to incr ease the volume. Press VOL – to decrease the volume. 3 Menu T urns the On-Screen Display (OSD) menus on and of f. 4 TV/A V Selects the input source to ...
-
HANNspree DT07-10A1 - page 20
19 Input and Output P o r ts Description Function 1 Left and right audio in (of A V1 ) Connects to VCR/VCD/DVD player CVBS RCA left and right audio cables (white and red). 2 DC-IN Connects to the inclu ded power adapter . 3 Headphone line out Connects to h eadphones or other audio device. 4 AV 2 Connects to the included 4-IN-1 cable. 5 Antenna/cabl ...
-
HANNspree DT07-10A1 - page 21
20 Connecting to an An tenna/Cable TV 1. Connect one e nd of the VHF/UHF (Antenna) or CA TV cable to ANT Jack (VHF/UHF IN Jack) on the back of the TV . 2. Connect the other end of the VHF/ UHF (Antenna) or CA TV cable to the Antenna socket or CA TV cable. Note If you cannot receive channels after connecting an Antenna or cable T V line, try scannin ...
-
HANNspree DT07-10A1 - page 22
21 Connecting to A V De vices Connect external devices such as VCD/DVD players or VCRs to the TV using the A V1 and A V2 ports on the back o f the TV . Connecting to a VCR, VCD or DVD Player The illustration presented here shows how to connect your TV to a VCR, VCD or DVD player . Actual c onnections vary according to the make and model of the devi ...
-
HANNspree DT07-10A1 - page 23
22 Connecting to a Video Camera The illustration presented here shows how to connect your TV to a camcorder or other type of digit al camera. Actual connections vary according to the make and model o f the device. Note The cables are co lo r-coded (black, re d, white, yellow). Connect each color- coded cab le to the appro priate connec tor on your ...
-
HANNspree DT07-10A1 - page 24
23 Connecting Exter nal Speak ers and Headphones Headphones or externa l speakers may be used to listen to the TV instead of the built-in speakers. Connect your h eadphones to the speaker/head phone line out port as illustrated. Notes • Exter nal speakers or headphones are not included with the pro du ct. • The intern al TV speakers will not ou ...
-
HANNspree DT07-10A1 - page 25
24 Connecting the P ow er Adapter 1. Connect the power cord to t he power adapter as illustrated. 2. Plug the power adapter connector in to the DC-IN on the rear p anel of the TV . 3. Insert the three-pronged plug at the other end of the power cord into a powe r outlet. Refer to the “Power Supply Safety Not es” on page 6. DC-IN AC power adapter ...
-
HANNspree DT07-10A1 - page 26
25 Using the R emote Control For best results, use the remote co ntrol within a dist ance of 5 meters from the front of the TV’ s signal sensor . Do not exceed an an gle of 30 degrees when pointing at the signa l sensor . Refer to the following illustration. 3m 30 5m 3m 30 30 30 C H V O L C H Using the TV 10 ...
-
HANNspree DT07-10A1 - page 27
26 T ur ning the TV On and Off 1. Press the POWE R button; the power indicator LED chang es from red to gre en, indicating that the power has been turned on. 2. Press the POWER button again; the power indicator LED changes from green to red, indi - cating that the TV is in standby (off) mode. Selecting Channels Press CH UP and CH DOWN on the contro ...
-
HANNspree DT07-10A1 - page 28
27 Switching Source Signals Press the SOURCE button on the remote control or the TV/A V button on the control p anel to select the incoming source signal. The current source setting CH XX appears on the top lef t corner of the screen; A V1 or A V2 appears on the bottom right corner of the screen. Note: The TV supports S-V ideo inpu t in addition to ...
-
HANNspree DT07-10A1 - page 29
28 The On-Screen Display (OSD) menu system provides a quick a nd simple method to adjust your TV’ s settings. This chapter describes how to change each of the available settin gs The OSD can be used with either the remote contro l or the front con- trol panel The following sections explain h ow to adjust settings in the OSD menus with the control ...
-
HANNspree DT07-10A1 - page 30
29 Brightness 1. Press MENU to enter the OSD menus. 2. Press the CH UP button or CH DOWN butt on to select Brightn ess. 3. Press MENU . The brightness slide bar is highlighted. 4. Press the CH UP button to increase the brightness. 5. Press the CH DOWN button to decrease the brightness. 6. Press MENU to confirm the s etting and return to the Main me ...
-
HANNspree DT07-10A1 - page 31
30 Contrast 1. Press MENU to enter the OSD menus. 2. Press the CH DOWN button or CH UP button to select Co ntrast. 3. Press MENU . The contrast slide bar is highlighted. 4. Press the CH UP button to increase the contrast. 5. Press the CH DOWN button to decrease the contrast. 6. Press MENU to confirm the s etting and return to the Main menu. Main Me ...
-
HANNspree DT07-10A1 - page 32
31 Video Setting Press the MENU button to enter the OSD Main Menu screen. 1. Press the CH DOWN button o r CH UP button to select Video Setting. 2. Press MENU to en ter the Video Settin g menu. Vid eo Setting Hue G B R G R ...
-
HANNspree DT07-10A1 - page 33
32 Hue 1. Press the CH DOWN button o r CH U P button to select Hue. 2. Press MENU to enter the Hue sub - menu. 3. Press the CH UP button to increase green and decrease red. 4. Press the CH DOWN button to decrease green and increase red. 5. Press MENU to confirm the s etting and return to the V ideo Setting menu. Vid eo Setting Hue G B R G R G R G R ...
-
HANNspree DT07-10A1 - page 34
33 Saturation 1. Press the CH DOWN button o r CH U P button to select Saturation. 2. Press MENU to enter t he Saturation submenu. 3. Press the CH UP button to increase the saturation. 4. Press the CH DOWN button to decrease the saturation. 5. Press MENU to confirm the s etting and return to the V ideo Setting menu. Vid eo Setting Saturation G B R 1 ...
-
HANNspree DT07-10A1 - page 35
34 Sharpness 1. Press the CH DOWN button or CH UP button to select Sharpness. 2. Press MENU to enter the SHARP - NESS submenu. 3. Press the CH UP button to increase the sharpness. 4. Press the CH DOWN button to decrease the sharpness. 5. Press MENU to confirm the s etting and return to the V ideo Setting menu. Vid eo Setting Sharpness G B R Note Th ...
-
HANNspree DT07-10A1 - page 36
35 Color T emperature 1. Press the CH DOWN button or CH UP button to select Color T emp. 2. Press MENU to enter the Color T em - perature submenu. There are three default color temperatures to choo se from. St andard Color Press the CH DOWN button o r CH UP button to select S tandard, then press MENU . W arm Color Press the CH DOWN button o r CH UP ...
-
HANNspree DT07-10A1 - page 37
36 Audio Setting Press the MENU button to enter OSD “Main Menu” screen. 1. Press the CH DOWN button o r CH UP button to select “Audio Setting”. 2. Press MENU to en ter the Audio Setting menu. Main Menu ETC Audio Setting ...
-
HANNspree DT07-10A1 - page 38
37 Tr e b l e 1. Press the CH DOWN button or CH UP button to select T reble. 2. Press MENU to enter t he treble submenu. 3. Press the CH UP button to increase the treble. 4. Press the CH DOWN button to decrease the treble. 5. Press MENU to confirm the s etting and return to the Audio Setting menu. TRE TRE BASS BASS T reble T reble Audio Setting Not ...
-
HANNspree DT07-10A1 - page 39
38 Bass 1. Press the CH DOWN button or CH UP button to select Bass. 2. Press MENU to enter the Bass sub - menu. 3. Press the CH UP button to increase the bass. 4. Press the CH DOWN button to decrease the bass. 5. Press MENU to confirm the s etting and return to the Audio Setting menu. TRE TRE BASS BASS Bass Bass Audio Setting Note The new setting i ...
-
HANNspree DT07-10A1 - page 40
39 Balance 1. Press the CH DOWN button or CH UP button to select Balance. 2. Press MENU to enter the Balance submenu. 3. Press the CH DOWN button to shift the balance to the lef t speaker . 4. Press the CH UP button to shift the balance to the right speaker . 5. Press MENU to confirm the s etting and return to the Audio Setting menu. Audio Setting ...
-
HANNspree DT07-10A1 - page 41
40 Mute 1. Press the CH DOWN button or CH UP button to select Mute. 2. Press MENU to enter the Mute sub - menu. 3. Press the CH UP button to turn the mute off. 4. Press the CH DOWN button to turn the mute on. 5. Press MENU to confirm the s etting and return to the Audio Setting menu. Audio Setting TRE TRE BASS BASS Mute Mute Off On Audio Setting TR ...
-
HANNspree DT07-10A1 - page 42
41 Note The setting menu is available when current select source is TV . TV Setting Press the MENU button to enter OSD Main Menu screen. 1. Press the CH DOWN button o r CH UP button to se lect TV Setting. 2. Press MENU to en ter the TV Setting menu. Main Menu ETC TV Setting ...
-
HANNspree DT07-10A1 - page 43
42 TV/CA TV 1. Press the CH DOWN button or CH UP button to select TV/CA TV . 2. Press MENU to enter the TV/CA TV submenu. Receiving Cable TV Press the CH UP button to select CA TV , then press MENU . Receiving Broadcast TV Press the CH DOWN but ton to select TV , then press MENU . TV Setting TV/CA TV TV TV CA TV( STD HRC IRC ) AM + - CH TV Setting ...
-
HANNspree DT07-10A1 - page 44
43 MTS 1. Press the CH DOWN button or CH UP button to select MTS. 2. Press MENU to enter the MTS sub - menu. Select from the following options. MAIN Press the CH DOWN button o r CH UP button to select MAIN. A green dot appears and MAIN is highlighted in yel - low . Press MENU again to confirm the selection. SAP Press the CH DOWN button o r CH UP bu ...
-
HANNspree DT07-10A1 - page 45
44 Auto Program 1. Press the CH DOWN button or CH UP button to selec t Auto Program. 2. Press MENU to enter the Auto Pro - gram Setting submenu. 3. Press the CH DOWN button or CH UP button t o select ON or OFF and press MENU . The screen shows “Auto Program...” and the channel indicator incremen ts from 2 to 69 (ANT connection) or from 1 to 125 ...
-
HANNspree DT07-10A1 - page 46
45 Manual Program 1. Press the CH DOWN button or CH UP button to select “Manual Program”. 2. Press MENU to enter the Manual Program submenu. 3. Press the CH DOWN b u t t o n and the CH UP button to find the channel you want to add. Press MENU to select the channel. 4. Press MENU to exit, and then access Channel Add/Erase function to add a desir ...
-
HANNspree DT07-10A1 - page 47
46 Channel Add/Erase 1. Select the channel you want to add or delete, for exampl e, Channel 28. 2. Press the CH DOWN button or CH UP button to select CH. Add/Erase. 3. Press MENU to enter the Channe l Add/Erase submenu. Select fro m the following options. Add Channel 1. Press the CH DO WN button or CH UP button to select Add. 2. Press MENU to selec ...
-
HANNspree DT07-10A1 - page 48
47 Favorite Ch annels 1. Press the CH DOWN button o r CH UP button to se lect Favorites CH. Edit. 2. Press MENU to enter the Favorites CH. Edit submenu. 3. The screen displays the four favor - ite channels: M1, M2, M3, and M4. 4. Press the CH DOWN button a n d the CH UP button to select the channel number you want to set for M1. Press MENU to c onf ...
-
HANNspree DT07-10A1 - page 49
48 Miscellaneous Setting Press the MENU button to enter OSD Main Menu screen. 1. Press the CH DOWN button o r CH UP button t o select Mis- cellaneous Setting. 2. Press MENU to en ter the Mis- cellaneous Setting menu. Main Menu ETC Miscellaneous Miscellaneous ...
-
HANNspree DT07-10A1 - page 50
49 Language 1. Press the CH DOWN button or CH UP button to select Language. 2. Press MENU to enter the Language submenu. 3. The screen displays the available OSD languages: English and T - Chinese (Traditional Chinese). 4. Press the CH DOWN button an d the CH UP button to select a lan guage. The OSD language changes as soon as you select a language ...
-
HANNspree DT07-10A1 - page 51
50 Sleep Timer The sleep timer turns the TV of f automatically after a set pe riod of time. 1. Press the CH DOWN button or CH UP button to select Sleeper . 2. Press MENU to enter the Sleeper submenu. 3. The screen displays the available sleep timer setting: Of f, 30, 60, 90, and 120 minutes. 4. Press the CH DOWN button an d the CH UP button to sele ...
-
HANNspree DT07-10A1 - page 52
51 OSD Display This setting allows you to set th e amount o f information that appears on the LCD screen when the DISPLA Y button is pressed. Y ou can choose from three settings: Of f, Portion, or All. 1. Press the CH DOWN button or CH UP button to select OSD Display . 2. Press MENU to enter the OSD Dis- play submenu. 3. The screen displays the ava ...
-
HANNspree DT07-10A1 - page 53
52 Time Setting This section shows you how to change your TV’ s clock setting. 1. Press the CH DOWN button or CH UP button to select T ime Setting. 2. Press MENU to enter t he T ime Set- ting submenu. 3. The screen displays the current set- ting. The hour is highlighted in yellow . 4. Press the CH DOWN button an d the CH UP button to adjust the h ...
-
HANNspree DT07-10A1 - page 54
53 Re se t The Reset function returns all of your TV’ s user settings to their fac- tory defaults. W arning: The reset function erases all of yo ur custom and favorite channel set- tings, and will reset all display settings (such as cont rast, brightness, etc.) to the fact ory default values. The reset funct ion cannot be reversed once it begins. ...
-
HANNspree DT07-10A1 - page 55
54 T urn the power off b efore you begin cleaning the TV. Use a clean lens cloth to remove dust and finger- prints from the screen. Do not wipe the shell of the TV with alcohol, methanol, gasoline or oil products to avoid the damaging the finish. Wipe the shell with a dry soft cloth a nd use neutral cleaning fluids. If your model has leat her compo ...
-
HANNspree DT07-10A1 - page 56
55 Situation Solution No picture and sound. • Connect the power cord prope rly . • Press the POWER button on the control panel or remote control. • Press the TV/A V button to cycle through connected video sources. • Press CH UP or CH DOWN to switch to other TV stations. • Check the TV/CA TV OSD se ttings. See “TV/CA T V” on page 42. ? ...
-
HANNspree DT07-10A1 - page 57
56 No sound but have image. • Make sure the source device is functioning properly . • Set the volume to a higher level. • Make sure the audio cable is connected securely . • T urn the mute off. Screen image turns over . • Make sure the video si gnal cable is connected properly . Snow appears on the screen. • Adjust the location of the A ...
-
HANNspree DT07-10A1 - page 58
57 Item Specifications DT07-10A1 LCD Panel Size 9.6-inch TFT Aspect Ratio 4:3 Best Resolution 800 (horizontal) x 600(vertical) Maximum Display Area 194.4 MM. (H) x 145.8 MM. (W) TV System NTSC Video System A V1: CVBS RCA jack A V2: S-Video or CVBS: 10-pin mini-DIN Audio System (Input) A V1: RCA left & right jacks (Input) A V2: RCA left & ri ...
-
HANNspree DT07-10A1 - page 59
58 Aspect Ratio The ratio of width to height of a film, image or display scree n. Broadcast TV Broadcasting video signals using high-frequency ele ctromagnetic waves to distribute television ch annels to viewers (standard TV broadcast). CA TV Community Antenna T elevision, the original name for cable TV . A television distribution system that uses ...
-
HANNspree DT07-10A1 - page 60
59 with camcorders, VCRs, and quality re ceiver s and amplifiers to provide sha rper pic- tures. VCD A compact disk format developed in 1993 by Sony and Philips to capture full- motion video. A standard Video CD can hold 74 minutes of near VHS-quality video and CD-quality sound. ...
¿Tienes una pregunta acerca de HANNspree DT07-10A1?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con HANNspree DT07-10A1, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con HANNspree DT07-10A1 probablemente compartirá una forma de solucionarlo.