-
Harbor Freight Tools 98135 - page 1
® FUEL TRANSFER PUMP 12VDC 98135 SET UP AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury . SA VE THIS MANUAL. Copyright © 200 ...
-
Harbor Freight Tools 98135 - page 2
Page 2 SKU 98135 For technical questions, please call 1-800-444-3353. SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures. Write the product’ s serial number in the back of the manual near the assembly diagram (or month and year of purchase if produc ...
-
Harbor Freight Tools 98135 - page 3
Page 3 SKU 98135 For technical questions, please call 1-800-444-3353. Use safety equipment. Wear ANSI- 5. approved safety gog gles, a dust mask/respirator (for fumes), and non- skid safety shoes during installation. General/Operation Safety DO NOT SMOKE 1. while using this Fuel T ransfer Pump. DO NOT use this pump near pilot lights, open ? ...
-
Harbor Freight Tools 98135 - page 4
Page 4 SKU 98135 For technical questions, please call 1-800-444-3353. product, but must be supplied by the operator . Maintenance Safety Have your equipment serviced by 1. a qualied repair person using only identical replacement parts. This will ensure that the safety of the equipment is maintained. Maintain labels and nameplates on 2. the pump. ...
-
Harbor Freight Tools 98135 - page 5
Page 5 SKU 98135 For technical questions, please call 1-800-444-3353. INITIAL SET UP INSTRUCTIONS Read the ENTIRE IMPORT ANT SAFETY INFORMA TION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJUR Y FROM ACCIDENT AL OPERA TION: T urn the Power Switch of ...
-
Harbor Freight Tools 98135 - page 6
Page 6 SKU 98135 For technical questions, please call 1-800-444-3353. system pressure. DO NOT install additional check valves or foot valves during installation without proper relief valves built into them. Systems should be set up requiring a 4. minimum amount of suction lift. The maximum vertical distance from the surface of the fuel inside the t ...
-
Harbor Freight Tools 98135 - page 7
Page 7 SKU 98135 For technical questions, please call 1-800-444-3353. Strip 6” of the outer insulation cover- 3. ing the Cable (60) being careful not to damage the wire insulation. Pass the stripped end of the Cable 4. (60) through the Cable Connector (53) until 2” of the unstripped wire is within the Motor Casing Assembly (6). Strip 1/2” of ...
-
Harbor Freight Tools 98135 - page 8
Page 8 SKU 98135 For technical questions, please call 1-800-444-3353. OPERA TION This Fuel T ransfer Pump must be set up according to all “Installation and Connection” information on pages 6 thru 8 of this manual. T o reduce build up of static electricity and possible re and/or explosion, do not wear synthetic bers while using this Fuel T ...
-
Harbor Freight Tools 98135 - page 9
Page 9 SKU 98135 For technical questions, please call 1-800-444-3353. MAINTENANCE AND SER VICING Procedures not specically explained in this manual must be performed only by a qualied technician. TO PREVENT SERIOUS INJUR Y FROM ACCIDENT AL OPERA TION: T urn OFF the power to the Fuel T ransfer Pump before any inspection or maintenance is perfo ...
-
Harbor Freight Tools 98135 - page 10
Page 10 SKU 98135 For technical questions, please call 1-800-444-3353. T roubleshooting Problem Possible Causes Likely Solutions Pump will not prime Suction Pipe (58) leak. 1. Bypass V alve (28) open. 2. V anes (33) sticking. 3. Inlet Gasket (26) leakage. 4. Excessive Rotor (34) or V ane 5. (33) wear . Motor not operating. 6. Motor is running backw ...
-
Harbor Freight Tools 98135 - page 11
Page 1 1 SKU 98135 For technical questions, please call 1-800-444-3353. T roubleshooting Problem Possible Causes Likely Solutions Motor Stalls Bypass V alve (28) sticking 1. Low voltage. 2. Excessive Rotor (34) or V ane 3. (33) wear . Remove and inspect Bypass V alve (28). 1. Check incoming line voltage. 2. Inspect Rotor (34) and V anes (33) for 3. ...
-
Harbor Freight Tools 98135 - page 12
Page 12 SKU 98135 For technical questions, please call 1-800-444-3353. P ARTS LIST Part Description Q’ty 1 Pump Housing 1 2 Ball Bearing 2 3 Armature Assembly 1 4 Motor Frame/Magnet Assembly 1 5 1/4-20 X 5” Thru-Bolt 2 6 Motor Casting Assembly 1 7 Switch Plate with Bushing 1 8 Thermal Protector 1 9 Brush Holder Assembly 2 10 Negative Brush Asse ...
-
Harbor Freight Tools 98135 - page 13
Page 13 SKU 98135 For technical questions, please call 1-800-444-3353. ASSEMBL Y DIAGRAM Record Product’ s Serial Number Here: Note: If product has no serial number , record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only , and are not avail- able individually as replacement parts. ...
-
Harbor Freight Tools 98135 - page 14
Page 14 SKU 98135 For technical questions, please call 1-800-444-3353. LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of one year from date of purchase that the tank is free of defects in ...
¿Tienes una pregunta acerca de Harbor Freight Tools 98135?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Harbor Freight Tools 98135, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Harbor Freight Tools 98135 probablemente compartirá una forma de solucionarlo.