-
Ryobi ELL0006 - page 1
OPERA TOR’S MANUAL AIRgrip ™ Pr oCr oss ™ LASER LEVEL SELF-LEVELING ELL0006 SA VE THIS MANUAL FOR FUTURE REFERENCE Y our laser level has been engineered and manufactur ed to our high standard for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-fr ee performance. WAR ...
-
Ryobi ELL0006 - page 2
2 Introduction ..................................................................................................................................................................... 2 General Safety Rules ...................................................................................................................................... ...
-
Ryobi ELL0006 - page 3
3 GENERAL SAFETY RULES WARNING! READ AND UNDERST AND ALL INSTRUCTIONS. Fail- ure to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury . CAUTION: Use of controls or adjustments or performance of pro- cedures other than those specified herein may result in hazardous radiation exposur e. CAUTION: ...
-
Ryobi ELL0006 - page 4
4 SYMBOLS Some of the following symbols may be used on this pr oduct. Please study them and lear n their meaning. Proper interpretation of these symbols will allow you to operate the pr oduct better and safer . V V olts V oltage A Amperes Current Hz Hertz Frequency (cycles per second) W W att Power min Minutes Time Alternating Current T ype of curr ...
-
Ryobi ELL0006 - page 5
5 SERVICE This unit has no serviceable parts. If the unit fails due to normal wear and tear within two years of purchase, return with original receipt for a replacement unit at no char ge. Call 1-800-525-2579 for your nearest AUTHORIZED SERVICE CENTER . WARNING: T o avoi d ser iou s per son al i nju ry , do no t att emp t to use th is product until ...
-
Ryobi ELL0006 - page 6
6 FEA TURES Fig. 1 PRODUCT SPECIFICA TIONS Recommended Use.....................................................................................................................................................Indoors AIRgrip Power Supply .......................................................................................................... 2 AA, 1 ...
-
Ryobi ELL0006 - page 7
7 FEA TURES KNOW YOUR CROSSHAIR LASER LEVEL See Figures 1 - 2. The safe use of this product requires an understanding of the information on the pr oduct and in this operator’ s manual as well as a knowledge of the pr oject you ar e attempting. Before use of this pr oduct, familiarize yourself with all oper - ating features and safety rules. ADJUS ...
-
Ryobi ELL0006 - page 8
8 ASSEMBL Y UNP ACKING This product has been shipped completely assembled. Carefully r emove the product and any accessories from the box. Make sure that all items listed in the packing list are included. Inspect the product carefully to make sure no breakage or damage occurred during shipping. Do not discar d the packing material until ...
-
Ryobi ELL0006 - page 9
9 OPERA TION Rotate the laser lens housing until the battery compart- ment comes into view . Remove battery cover plate. Install two AA batteries accor ding to polarity indicators (+ or −) inside the battery compartment. Reinstall the battery cover plate. NOTE: Remove the batteries from both the vacuum base and the las ...
-
Ryobi ELL0006 - page 10
10 OPERA TION ROUGH SURF ACE ADAPTOR See Figure 7. By using the rough surface adaptor , you can use the AIRgrip feature to position the unit on many non-smooth surfaces, including brick and painted cinder block. NOTE: The AIRgrip feature cannot be used with stucco or unpainted cinder block. Place the adaptor over the AIRgrip base. Pla ...
-
Ryobi ELL0006 - page 11
11 OPERA TION Fig. 11 USING A TRIPOD See Figure 10. The laser level has a 5/8 in.-20 thr eaded fitting for attaching to a tripod base (not included). This method of mounting is ideal for leveling kitchen cabinets, countertops, window framing, and more. If a 1/4 in. tripod fitting is needed, thread the adaptor inside the 5/8 in. mounting hole and ti ...
-
Ryobi ELL0006 - page 12
12 MODEL NO. ELL0006 WA VE LENGTH: 630-670 NM MAX. PO WER OUTPUT < 5MW CLASS IIIA LASER PRODUCT LASER RADIA TION- A VOID DIRECT EYE EXPOSURE Complies with 21 CFR parts 1040.10 and 1040.11 Rayonnement laser - éviter le contact oculaire direct Lire les instructions du manuel. PE LIG R O Radiación láser - Evite la exposición directa de los ojos ...
-
Ryobi ELL0006 - page 13
13 TROUBLESHOOTING Pr oblem Possible Cause Solution V acuum not running. Batteries are low . Power is turned off. Replace batteries. Press on/of f button. Laser line projection is weak. Batteries are low . Replace batteries. Laser line is hard to see. Light in ar ea is too bright. Line is being projected beyond the specifications listed earlier in ...
-
Ryobi ELL0006 - page 14
ONE WORLD TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson, SC 29625 Phone 1-800-525-2579 www .ryobitools.com OPERA TOR’S MANUAL AIRgrip ™ Pr oCr oss ™ LASER LEVEL SELF-LEVELING ELL0006 983000-974 6-19-07 (REV :02) • SER VICE This pr oduct has no serviceable parts. If unit fails due to normal wear and tear within two years of purchase, r ...
¿Tienes una pregunta acerca de Ryobi ELL0006?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Ryobi ELL0006, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Ryobi ELL0006 probablemente compartirá una forma de solucionarlo.