-
ASA Electronics AVT-1928 - page 1
INSTRUCTION MANUAL AVT-1928 The serial number is located on the rear of the set. For future reference, please copy the number here. Serial No._________________________________ PPLICATIONS, L.L.C. UDIOVOX PECIALIZED 19” COLOR TELEVISION ...
-
ASA Electronics AVT-1928 - page 2
WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S ATTENTION TO ARTICLE 820-40 O ...
-
ASA Electronics AVT-1928 - page 3
Table of Contents Important Safeguards……………………………………………………………..2 Chapter1: Overview of Your equipment………………………………………..4 Your TV’s Front Panel……………………………………………………….4 Your TV’s Back Panel……………………………………? ...
-
ASA Electronics AVT-1928 - page 4
IMPORTANT SAFEGUARDS PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR TELEVISION EQUIPMENT AND RETAIN FOR FUTURE REFERENCE. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE TV RECEIVER. 1. Read all of these instructions. 2. Save these instructions for later use. 3. Unplug this television equipment from the wall outlet before cleaning. Do not use ...
-
ASA Electronics AVT-1928 - page 5
13. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, where it can fall into such power lines or circuits. When installing an outside antenna system. Extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 14 ...
-
ASA Electronics AVT-1928 - page 6
Overview of your Equipment Your TV comes with a remote control. The section below summarizes the buttons, controls and terminals that you will use with your TV. Your TV’s Front Panel 1. POWER Use this button to turn your TV on or off. 2. ù ù CH ü ü Use these buttons to change channels on your TV, or to select items in the menu system. 3. ÿ ? ...
-
ASA Electronics AVT-1928 - page 7
Your Remote Control 1. POWER Use this button to turn your TV on or off. 2. CH Use these buttons to change channels on your TV, or select items in the menu system. 3. VOL Use these buttons to change your TV’s volume, to activate selections in the menu system, or to change audio and video settings. 4. MENU Use this button to turn ...
-
ASA Electronics AVT-1928 - page 8
Installing your remote control batteries 1. Open the battery compartment on the back of the remote control. 2. Install two AAA-size batteries (not included) as shown. Make sure the “+” and “-“ terminals are oriented correctly. 3. Replace the cover. Notes Do not mix different types of batteries, or mix an old and a new battery. Remove and re ...
-
ASA Electronics AVT-1928 - page 9
Connecting an Antenna or cable to Your TV Your TV will provide you with the best performance if you connect it to an external antenna or cable system. Follow the directions below to make this connection. Please note that you will normally only have to make one of the connections shown below, not all of them. All connections will be made to the ante ...
-
ASA Electronics AVT-1928 - page 10
Chapter 2: Connecting to an Antenna or Cable to your TV- 7 Antennas with two sets of leads You might have two sets of leads from your antenna system, especially if you have one antenna for VHF signals and one antenna for UHF signals. If your antenna system has both a coaxial lead and twin 300 ohm leads, you must obtain a combiner (available at your ...
-
ASA Electronics AVT-1928 - page 11
If your cable system requires you to use a converter box for all channels, connect the incoming cable to the IN terminal on the converter box. Connect another cable between the OUT terminal on the converter box and the antenna terminal on the TV. If your cable system only requires you to use a converter box for some channels (i.e. pay-TV channels), ...
-
ASA Electronics AVT-1928 - page 12
Operating Your TV Once you have connected your TV to an antenna or cable system, unplugged the TV in, and put batteries in the remote, you are ready to use the TV. The first thing you should do is program your TV so it memorizes all of the available channels. Turning Your TV On Programming Your TV’s Channel Memory Your TV’s memory determines th ...
-
ASA Electronics AVT-1928 - page 13
Changing Channels You can change channels in three ways: Changing the Volume Changing the TV’s Channel Memory Your TV’s memory determines the channels that are available using the C H buttons. You can add channels to this memory or remove them from memory. If a channel is removed from memory, you can tune to it with the number buttons, bu ...
-
ASA Electronics AVT-1928 - page 14
Erasing a channel from memory Changing the TV’s channel memory with the menus You can also use the menu system to add/erase channels from memory: 1. Use the number buttons to tune to the channel, then press MENU. 2. Use the CH buttons to select SETUP and press VO L . 3. Use the CH buttons to select EDIT PROGRAM. If the channel i ...
-
ASA Electronics AVT-1928 - page 15
Adjusting Video Settings You may wish to adjust the video settings (e.g. contrast or color) to obtain the most pleasing picture. To do so follow these directions: 1. With the TV on, press the MENU button. 2. Use the CH buttons to select PICTURE. 3. Press the VO L button. The picture menu will appear. 4. The AUTO feature will be selected ...
-
ASA Electronics AVT-1928 - page 16
Returning to the factory settings If you would like to return to the original video settings, as they were calibrated at the factory, follow these steps: 1. Complete steps 1-3 in the “Adjusting Video Settings” section, on the previous page. 2. Press the VO L button to set the AUTO setting to ON. This will return all video settings to thei ...
-
ASA Electronics AVT-1928 - page 17
Using Timer Functions Your TV has a built in clock, and you can set the TV to turn on and off at times that you select. You can also set your TV to turn off after counting down a certain amount of time. Accessing the Timer Menu 1. With the TV turned on, press the MENU button. 2. Use the CH buttons to select TIMER. 3. Press the VO L butt ...
-
ASA Electronics AVT-1928 - page 18
Setting the On Timer If you enter a time in the ON TIME setting, your TV will automatically turn on at that time. Follow these instructions to set the ON TIME: 1. Follow steps 1-3 in ”Accessing the Timer Menu” on the previous page. 2. Use the CH buttons to select ON TIME. 3. Press the VOL button to set the hours (including AM/PM); pres ...
-
ASA Electronics AVT-1928 - page 19
3. Press the VOL button to set the hours (including AM/PM); press the VO L button to set the minutes. If you hold down either VOL button, the corresponding numbers will change more quickly. 4. When the setting is correct, use the C H buttons to select another timer function, or use the MENU button to exit this menu. Canceling the On Tim ...
-
ASA Electronics AVT-1928 - page 20
Additional Features This section contains descriptions of the advanced features of your TV. Changing the Language of the On Screen Menus You can choose to display the on screen menus in English, Spanish, or French. To change the on screen language: 1. With the Tv turned on, press the MENU button. 2. Use the CH buttons to select SETUP and pres ...
-
ASA Electronics AVT-1928 - page 21
5. Wait 5 seconds, or press the MENU button twice to return to normal TV viewing. Your setting will remain intact until you change it. About captions Once you have chosen a caption setting, all available captions on that setting will be displayed when you watch TV. If no captions appear, it is because there are no captions being broadcast for that ...
-
ASA Electronics AVT-1928 - page 22
Protection Features The following two features protect your TV from operating unnecessarily. Automatic Blue Screen If your television is tuned to a channel that is not receiving a signal (or is receiving a very weak signal), your TV will automatically display a blue screen instead of static. Automatic Power Off If your television does not receive a ...
-
ASA Electronics AVT-1928 - page 23
Troubleshooting Your Audiovox television is designed to give you trouble-free performance for many years. If you have a problem with your TV, try the solutions listed below. If the suggestions listed below do not solve your problem, contact your Audiovox dealer or an authorized Audiovox service center. You can also call Audiovox directly at (219) 2 ...
-
ASA Electronics AVT-1928 - page 24
90 DAY/12 MONTH LIMITED WARRANTY APPLIES TO AUDIOVOX VIDEO PRODUCT Audiovox Specialized Applications, LLC (the company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purch ...
-
ASA Electronics AVT-1928 - page 25
Description Part Number AVT-988 9” Color Television with Remote (12V) AVT988 AVT-597 5” Color Television with Remote (12V) AVT597 AVT-1498 13” Color Television with Remote (12V) AVT1498 AVP-7000 Video Cassette Player (12V) AVP7000 AVP-7285 Video Cassette Player (12V) AVP7285 Wireless Headphone Kit: Includes 2 sets Wireless Headphones and Tran ...
-
ASA Electronics AVT-1928 - page 26
Audiovox Specialized Applications, LLC 23319 Cooper Dr. Elkhart, IN 46514 This instrument is listed by Underwriter’s Labortories, Inc. It is designed and manufactured to meet rigid U.L. safety standards against X-radiation, fire, casualty and electrical hazards. L U ...
¿Tienes una pregunta acerca de ASA Electronics AVT-1928?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con ASA Electronics AVT-1928, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con ASA Electronics AVT-1928 probablemente compartirá una forma de solucionarlo.