-
Patton electronic 1060rc - page 1
USER MANUAL MODEL 1060RC AC Powered, Asynchronous Short Range Modem: Rack Mount Card SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part #07M1060RC-B Doc #058021U , Rev C Revised 1/23/08 CERTIFIED An ISO-9001 Certified Company ...
-
Patton electronic 1060rc - page 2
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1060RC components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorize ...
-
Patton electronic 1060rc - page 3
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1060RC components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorize ...
-
Patton electronic 1060rc - page 4
3.0 CONFIGURA TION This section describes the location and orientation of the Model 1060RC's configuration switches and provides detailed instructions on setting each of the switches. 3.1 FRONT CARD CONFIGURA TION The Model 1060RC uses a set of eight DIP switches that allow configuration to a wide range of asynchronous applications. These DIP ...
-
Patton electronic 1060rc - page 5
3.0 CONFIGURA TION This section describes the location and orientation of the Model 1060RC's configuration switches and provides detailed instructions on setting each of the switches. 3.1 FRONT CARD CONFIGURA TION The Model 1060RC uses a set of eight DIP switches that allow configuration to a wide range of asynchronous applications. These DIP ...
-
Patton electronic 1060rc - page 6
Control Input (C in ): The Control Input signal is used by the local Model 1060RC as an input signal to “turn on” (in the “Enabled” settings) and allow data transmission to the remote device. This is required for half-duplex/ switched-carrier environments as well as in hardware flow control applications. In the “Disabled” settings, the ...
-
Patton electronic 1060rc - page 7
Control Input (C in ): The Control Input signal is used by the local Model 1060RC as an input signal to “turn on” (in the “Enabled” settings) and allow data transmission to the remote device. This is required for half-duplex/ switched-carrier environments as well as in hardware flow control applications. In the “Disabled” settings, the ...
-
Patton electronic 1060rc - page 8
3.4 REAR CARD CONFIGURA TION The 1060RC has four interface card options: DB-25/RJ-1 1, DB-25/RJ-45, RJ-45/RJ-1 1 and dual RJ-45. Each of these options supports one RS-232 connection and one 4-wire connection (the RS- 232 port is always the lower port on the interface card). Figure 4 (below) illustrates the four different interface options for the M ...
-
Patton electronic 1060rc - page 9
3.4 REAR CARD CONFIGURA TION The 1060RC has four interface card options: DB-25/RJ-1 1, DB-25/RJ-45, RJ-45/RJ-1 1 and dual RJ-45. Each of these options supports one RS-232 connection and one 4-wire connection (the RS- 232 port is always the lower port on the interface card). Figure 4 (below) illustrates the four different interface options for the M ...
-
Patton electronic 1060rc - page 10
The table below provides an overview of strap functions for the DB- 25/modular cards. Following this overview is a detailed description of each strap's function. Line Shield & FRGND (JB2) This strap pertains to the line interface. In the connected (closed) position, this strap links RJ-1 1 pins 1 and 6, or RJ-45 pins 2 and 7 to frame groun ...
-
Patton electronic 1060rc - page 11
The table below provides an overview of strap functions for the DB- 25/modular cards. Following this overview is a detailed description of each strap's function. Line Shield & FRGND (JB2) This strap pertains to the line interface. In the connected (closed) position, this strap links RJ-1 1 pins 1 and 6, or RJ-45 pins 2 and 7 to frame groun ...
-
Patton electronic 1060rc - page 12
SGND & FRGND (JB5) This strap pertains to the DTE interface, which is a 10-position modular RJ-45 jack. In the connected (closed) position, this strap links modular pin 5 (Signal Ground) and frame ground. In the open (disconnected) position, pin 5 is "lifted" from frame ground. JB5 Position 1&2 = SGND (pin 5) and FRGND Connected P ...
-
Patton electronic 1060rc - page 13
SGND & FRGND (JB5) This strap pertains to the DTE interface, which is a 10-position modular RJ-45 jack. In the connected (closed) position, this strap links modular pin 5 (Signal Ground) and frame ground. In the open (disconnected) position, pin 5 is "lifted" from frame ground. JB5 Position 1&2 = SGND (pin 5) and FRGND Connected P ...
-
Patton electronic 1060rc - page 14
Switching the Power Supply On and Off The power supply on/off switch is located on the front panel. When plugged in and switched on, a red front panel LED will glow . Since the Model 1000R16 is a "hot swappable" rack, it is not necessary for any cards to be installed before switching on the power supply . The power supply may be switched ...
-
Patton electronic 1060rc - page 15
Switching the Power Supply On and Off The power supply on/off switch is located on the front panel. When plugged in and switched on, a red front panel LED will glow . Since the Model 1000R16 is a "hot swappable" rack, it is not necessary for any cards to be installed before switching on the power supply . The power supply may be switched ...
-
Patton electronic 1060rc - page 16
RJ-45 SIGNAL PIN# COLOR COLOR PIN# SIGNAL GND 2 Orange .............Brown 7 GND RCV - 3 Black ................Green 5 XMT - XMT+ 4 Red ..................Y ellow 6 RCV+ XMT - 5 Green ...............Black 3 RCV - RCV+ 6 Y ellow ..............Red 4 XMT+ GND 7 Brown ..............Orange 2 GND 4.4.2 Multipoint T wisted Pair Connection Figure 1 1 (below) ...
-
Patton electronic 1060rc - page 17
RJ-45 SIGNAL PIN# COLOR COLOR PIN# SIGNAL GND 2 Orange .............Brown 7 GND RCV - 3 Black ................Green 5 XMT - XMT+ 4 Red ..................Y ellow 6 RCV+ XMT - 5 Green ...............Black 3 RCV - RCV+ 6 Y ellow ..............Red 4 XMT+ GND 7 Brown ..............Orange 2 GND 4.4.2 Multipoint T wisted Pair Connection Figure 1 1 (below) ...
-
Patton electronic 1060rc - page 18
5.2 POWER-UP There is no power switch on the Model 1060RC: Power is automatically applied to the 1060RC when its card-edge connector makes contact with the chassis' mid-plane socket, or when the chassis' power supply is turned on. Note: The 1060RC is a "hot swappable" card—it will not be damaged by plugging it in or removing i ...
-
Patton electronic 1060rc - page 19
5.2 POWER-UP There is no power switch on the Model 1060RC: Power is automatically applied to the 1060RC when its card-edge connector makes contact with the chassis' mid-plane socket, or when the chassis' power supply is turned on. Note: The 1060RC is a "hot swappable" card—it will not be damaged by plugging it in or removing i ...
-
Patton electronic 1060rc - page 20
APPENDIX A SPECIFICA TIONS T ransmission Format: Asynchronous External Interface: RS-232C/CCITT V .24 connection via DB-25 female; EIA/TIA-561 connection via RJ-45 (10 wire); twisted pair connection via RJ-1 1 or RJ-45 (8 wire) Internal Interface: Connection to Model 1000R16 rack chassis via 50 pin male card edge T ransmission Line: 4-wire, uncondi ...
-
Patton electronic 1060rc - page 21
APPENDIX A SPECIFICA TIONS T ransmission Format: Asynchronous External Interface: RS-232C/CCITT V .24 connection via DB-25 female; EIA/TIA-561 connection via RJ-45 (10 wire); twisted pair connection via RJ-1 1 or RJ-45 (8 wire) Internal Interface: Connection to Model 1000R16 rack chassis via 50 pin male card edge T ransmission Line: 4-wire, uncondi ...
-
Patton electronic 1060rc - page 22
APPENDIX C F ACTOR Y REPLACEMENT P ARTS The Patton Model 1060RC rack system features interchangeable rear half cards, power cords/fuses for international various operating environments and other user-replaceable parts. Model numbers and descriptions for these parts are listed below: Patton Model # Description 1000RPEM ..........................120/ ...
-
Patton electronic 1060rc - page 23
APPENDIX C F ACTOR Y REPLACEMENT P ARTS The Patton Model 1060RC rack system features interchangeable rear half cards, power cords/fuses for international various operating environments and other user-replaceable parts. Model numbers and descriptions for these parts are listed below: Patton Model # Description 1000RPEM ..........................120/ ...
-
Patton electronic 1060rc - page 24
APPENDIX E BLOCK DIAGRAM Dear V alued Customer , Thank you for purchasing Patton Electronics products! W e do appreciate your business. I trust that you find this user manual helpful. W e manufacture one of the widest selections of data communications products in the world including CSU/DSU's, network termination units, powered and self-powere ...
-
Patton electronic 1060rc - page 25
...
-
Patton electronic 1060rc - page 26
...
-
Patton electronic 1060rc - page 27
...
-
Patton electronic 1060rc - page 28
APPENDIX E BLOCK DIAGRAM Dear V alued Customer , Thank you for purchasing Patton Electronics products! W e do appreciate your business. I trust that you find this user manual helpful. W e manufacture one of the widest selections of data communications products in the world including CSU/DSU's, network termination units, powered and self-powere ...
¿Tienes una pregunta acerca de Patton electronic 1060rc?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Patton electronic 1060rc, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Patton electronic 1060rc probablemente compartirá una forma de solucionarlo.