-
GE ZV850 - page 1
GE Monogram ® Installation Instr uctions 36" Island V ent Hood Model ZV850 ...
-
GE ZV850 - page 2
2 Before you begin — Read these instr uctions completely and carefully . IMPORT ANT - Save these instructions for local inspector’s use. IMPORT ANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer - Be sure to leave these instr uctions with the Consumer . Note to Consumer - Keep these instr uctions with your Use and Care Book for ...
-
GE ZV850 - page 3
3 Design Infor mation 36" Island Vent Hood Model ZV850 Model Available Required Accessor y This vent hood is designed to be used in vented ceiling mounted installations. NOTE: Accessories to meet proper ceiling height are required to complete the installation. The vent hood must be installed 24” min. and 30” max. above the cooking sur face ...
-
GE ZV850 - page 4
4 Installation Preparation 36" Island Vent Hood • Tape measure • Knife • Spirit level • Wire cutter • Wire stripper • Wire nuts • Electric drill and 5/32” bit • Phillips screwdriver • Flat blade screwdriver • Hammer • Pliers • 10 mm Hex wrench/socket • Safety glasses • Tape to mount template • Gloves to protect ...
-
GE ZV850 - page 5
5 Installation Preparation 36" Island Vent Hood Duct fittings T otal Equivalent Quantity Equivalent Duct Piece Dimensions Length* Used Length Round, 1 ft. straight (per foot length) 3 -1 ⁄ 4" x 10" 1 ft. straight (per foot length) 90 ° elbow 15 ft. 45 ° elbow 9 ft. 3 -1 ⁄ 4" x 10" 90 ° elbow 15 ft. 3 -1 ⁄ 4" x ...
-
GE ZV850 - page 6
6 Installation Preparation 36" Island Vent Hood Advance Planning 1 Step Note: The cross framing must be spaced 8-3/4” on the side from centerline to centerline in order to accept the hood mounting screws. Plan the location Determine the exact location of the vent hood. • Use a plumb to check location to be sure countertop/cooktop location ...
-
GE ZV850 - page 7
7 Installation Preparation 36" Island Vent Hood Advance Planning (continued) 1 Step Ductwork • Use the shortest and straightest duct route possible. For satisfactor y per for mance, duct r un should not exceed 100 feet equivalent length for any duct configuration. • Refer to “Duct Fittings” chart to compute the maximum permissible leng ...
-
GE ZV850 - page 8
8 Installation 36" Island Vent Hood Check Installation Hardware 3 Step Check contents of the required accessory, ZX858, ZX859 or ZX8510. Locate the hardware accessory box packed with the hood and check contents. 4 Hex head wood lag screws (6mm x 2-1/2") or (1/4 x 2-1/2") 4 Flat Washers 8 Frame Attachment Screws with Washers (attached ...
-
GE ZV850 - page 9
9 Installation 36" Island Vent Hood • Align the template with the marks on the ceiling and tape in place. – Be sure the template is oriented cor rectly , with the front of the hood. • Use a plumb to check to be sure the mount- ing holes will provide parallel alignment with the countertop below . • Center punch all hole locations. • D ...
-
GE ZV850 - page 10
10 Installation 36" Island Vent Hood Wiring • Route house wiring through the ceiling hole and pull a length to reach the hood junction box, approximately 6” below the support. • T ape the wire to the front of the frame support to prevent damage during installa- tion and ser vice. 7 Step Size And Install Ductwork T o Find Required Duct Le ...
-
GE ZV850 - page 11
Installation 36" Island Vent Hood Install Decorative Duct Covers Step 8 11 • Pretap or drive decorative screw into the screw holes on the support frame. This will make screw installation easier . • Separate the two decorative duct covers. • Select the inside (top) cover , which has two screw holes in the top. • Slide the decorative duc ...
-
GE ZV850 - page 12
12 Installation 36" Island Vent Hood 10 Step Connect Electrical V erify that power is tur ned of f at the source. CAUTION If house wiring is not 2-wire with a ground wire, a ground must be provided by the installer . When house wiring is aluminum, be sure to use U.L. approved anti- oxidant compound and alumi- num-to-copper connectors. WARNING ...
-
GE ZV850 - page 13
13 Installation 36" Island Vent Hood Slide Duct Cover Down, Install Side Utility Bars Step 11 • Hold the decorative duct cover and remove the temporar y stop screw . Retur n the screw to the ser vice manual envelope for future use. • Slide the lower duct cover down onto the hood. • Install the side utility bars with screws as shown. ...
-
GE ZV850 - page 14
14 Installation 36" Island Vent Hood • Remove protective film on filters. • Tip the filter into the lower slots at the rear of the opening. Lift the filter and pull the knob for ward until the filter rests on the slots. • T o remove the filters, grasp the knob, push the filter towards the rear and tilt down- wards. 12 Step Finalize Insta ...
-
GE ZV850 - page 15
Notes 36" Island Vent Hood 15 ...
-
GE ZV850 - page 16
Pub. No. 49-8970-1 Dwg. No. 164D3333P197 1999 GE Appliances (N.D. 500) 12/99 04306398 Monogram. ® General Electric Company Louisville, KY 40225 Note: While performing installations described in this book, safety glasses or goggles should be worn. T o obtain specific information concer ning any Monogram product or ser vice, call GE Answer Cente ...
¿Tienes una pregunta acerca de GE ZV850?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con GE ZV850, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con GE ZV850 probablemente compartirá una forma de solucionarlo.