-
Audiovox 128-7853 - page 1
128-7853 1 of 16 1 Model APS-920 Inst allation Manual This Remote St art/Alarm System is designed to be used with Automatic T ransmission- Fuel Injection V ehicles Only! COMPONENTS: Control Module 1 Four Button RF T ransmitter 1 Four Button LCD T ransmitter 2 Way Antenna/Receiver 1 “1 X 1.75” Foam Pad 6 Pin Main Power Harness w/Fuses 20 Pin Acc ...
-
Audiovox 128-7853 - page 2
128-7853 2 of 16 2 INST ALLA TION OF THE MAJOR COMPONENTS: CONTROL MODULE: Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location selected must be within 24" of the ignition switch wiring harness to allow con- nection of the 6 pin main wiring harness. Be certain that the chosen location wil ...
-
Audiovox 128-7853 - page 3
128-7853 3 of 16 3 SIREN: Select a location in the engine compartment that is not accessible from below the vehicle. The selected location must be clear of hot or moving parts within the engine compartment The siren must be pointed downward to prevent water retention and the flared end must be pointed away from and out of the engine compartment for ...
-
Audiovox 128-7853 - page 4
128-7853 4 of 16 4 DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MUL TI PIN INPUT / OUTPUT HARNESS INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HA VE BEEN MADE. AFTER SELECTING YOUR T ARGET WIRES AS DEFINED BELOW , DISCON- NECT THE NEGA TIVE BA TTERY CABLE FROM THE VEHICLE BA TTERY PRIOR T O MAKING ANY CONNECTIONS. Note: Do not ...
-
Audiovox 128-7853 - page 5
128-7853 5 of 16 5 BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the "ON" or "RUN" and the "ST ART" or CRANK" positions, and will have 0 volts when the key is turned to the "OFF" and "A ...
-
Audiovox 128-7853 - page 6
128-7853 6 of 16 6 false triggering of the factory alarm when the remote start unit engages or when the transmitter is used to unlock the doors. NOTE: This output can be selected to operate like the door lock output as set in alarm feature setting #1 by selecting feature #13 of Bank 3 to as door unlock pulse. Black w/ Light Green T race Wire: Pulse ...
-
Audiovox 128-7853 - page 7
128-7853 7 of 16 7 Orange: Ground While Armed Output This wire provides a 300 mA ground output when the alarm circuit is armed to control the starter inhibit relay . Connect the Orange wire to terminal #86 (orange wire) of the relay provided. Connect terminal #85 (red wire) of the relay to an ignition wire in the vehicle that is +12 volts when the ...
-
Audiovox 128-7853 - page 8
128-7853 8 of 16 8 Brown Wire: Negative Door Trigger If the vehicle's door courtesy light switches ground when the door is opened, (Most GMs and Imports), you must connect this wire to the negative output from one of the vehicle's door pin switches. In most cases the Brown wire will need to be connected to only one door switch no matter h ...
-
Audiovox 128-7853 - page 9
128-7853 9 of 16 9 Green/Y ellow Wire: DIESEL W AIT T O ST ART INPUT The green/yellow wire, when connected to the wire that get + 12 volts during the glow plug preheat stage will delay the starter output until this wire drops the 12 volts. In other words, in a Diesel vehicle with glow plug preheat circuit, when the ignition is turned on, the vehicl ...
-
Audiovox 128-7853 - page 10
128-7853 10 of 16 10 The Light Blue wire can be used to accommodate the following situations: A. Shock Sensor By Pass: B. Additional Ignition Output: C. GM V A TS Key Override: Green w/ Black T race Wire: 250 mA Latched Channel 4 Output The Green w/ Black Trace wire supplies a 300 mA switched output whenever channel four of the receiver is accessed ...
-
Audiovox 128-7853 - page 11
128-7853 11 of 16 11 4 Pin Shock Sensor Connector “D” Red, Black Green & Blue wires of the shock sensor harness provide +12 V olts, Ground, Full T rigger , and Pre-Detect inputs to and from the sensor . Route these wires from the previously installed sensor and connect to the mating connector on the control module. 2 Pin LED Harness, Connec ...
-
Audiovox 128-7853 - page 12
128-7853 12 of 16 12 ...
-
Audiovox 128-7853 - page 13
128-7853 13 of 16 13 Setting Up The System Programming Features: Bank 1 Transmitter Channels S tart with the system disarmed, tun the ignition switch to the on position then: 1) Press and release the push button valet/program switch 3 times. Siren Chirps once and or Lights flash one time indicating the transmitter program mode successfully entered. ...
-
Audiovox 128-7853 - page 14
128-7853 14 of 16 14 Programming T ach Rate: NOTE: All applications require that tach be programmed. The unit will not operate unless tach is programmed. If an attempt is made to start the vehicle via the remote start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored. If t ...
-
Audiovox 128-7853 - page 15
128-7853 15 of 16 15 3. Within 10 seconds of the key turning off, cycle the enable switch Off, On, Off, On ( 2 times) to select a 2 hour timed start interval. Cycle the enable switch Off, On, Off, On, Off, On, Off, On (4 times) to select a 4 hour timed start interval. The lights will flash and the siren will chirp 2X or 4X dependant upon 2 or 4 hou ...
-
Audiovox 128-7853 - page 16
128-7853 16 of 16 16 © 2006 Audiovox Electronics Corporation 150 Marcus Blvd. Hauppauge N.Y . 1 1788 128-7853 ...
¿Tienes una pregunta acerca de Audiovox 128-7853?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Audiovox 128-7853, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Audiovox 128-7853 probablemente compartirá una forma de solucionarlo.