-
JVC FS-X3 - page 1
SP-FSX1 CA-FSX1 SP-FSX1 SP-FSX3 CA-FSX3 SP-FSX3 COMP A CT COMPONENT SYSTEM For Customer Use: Enter below the Model No . and Serial No. which are located either on the rear , bot- tom or side of the cabinet. Retain this information for future r eference. M o d e l N o. S e r i a l N o. INSTR UCTIONS L VT1040-007 A [US] FS-X1/FS-X3 Consists of CA-FSX ...
-
JVC FS-X3 - page 2
G-1 W arnings, Cautions and Others CA U TION T o reduce the risk of e lectrical shocks , fire, etc.: 1. Do not remove scre ws, cov ers or cabinet. 2. Do not expose this appliance to rain or moisture. Caution –– ST ANDBY/ON button! Disconnect the main plug to shu t the power off completely . The ST ANDBY/ON button in any position does not dis- c ...
-
JVC FS-X3 - page 3
G-2 Caution: Proper V entilation T o avoid risk of electric shock and fire , and to prev ent damage, locate the apparatus as f ollows: 1 F r ont: No obstructions and open spacing. 2 Sides/ T op/ Back: No obstructions should be placed in the areas shown by the dimensions below . 3 Bottom: Place on the lev el surface. Maintain an adequate air path f ...
-
JVC FS-X3 - page 4
1 English Introduction Thank you for purchasing the JVC Compact Component System. We hope it will be a valued addition to your home, giving you years of enjoyment. Be sure to read this instruction manual carefully befo re operating your new stereo system. In it you will find all the information you need to set up and use the system. If you have a q ...
-
JVC FS-X3 - page 5
2 Table of Contents English Introduction .............................................. .......................................................... 1 Features ............. ................. ................ ................. ................. ................. .................... .. ............... 1 How This Manual Is Organized .... ............. ...
-
JVC FS-X3 - page 6
Table of Contents 3 English Setting the Daily Timer ................. ................. ................. ................... ................. ................. .... 23 Setting the SLEEP Timer .............. ................. ................. ................. ................. ................ ...... .2 6 Timer Priority .... ................. .. ...
-
JVC FS-X3 - page 7
4 English Getting Started Accessories Make sure that you have all of the following items, which are supplied with the System. FM Wire Antenna (1) AM Loop Antenna (1) Remote Control (1) Batteries (2) Speaker Cords (2) AC plug adaptor (1) If any of these items are missing, contact your dealer immediately. How To Put Batteries In t he Remote Control M ...
-
JVC FS-X3 - page 8
5 Getting Started English CAUTI ON: • Make all connecti ons before plugging the Syst em into an AC power outlet. Connecting the FM Antenna Rear Panel of the Center Unit (CA-FSX1/CA-FSX3) Using the Supplied Wire Antenna • Fasten it up in the position until you ha ve the best reception. If reception is poor, connect the outdoor antenna. Using the ...
-
JVC FS-X3 - page 9
6 Getting Started English Connecting the AM Antenna Rear Panel of the Center Unit (CA- FSX1/CA-FSX3) • If the AM loop antenna wire is covered with vinyl, remove the vinyl by twisting it as shown in the diagram. • Make sure the antenna conductors do not t ouch any other terminals, connecting cords and power cord. This could cause poor reception. ...
-
JVC FS-X3 - page 10
7 Getting Started English Connecting the Speakers (SP-FSX1/SP-FSX3) These speakers are exclusively for this system . Using with other devices will damage the speakers. Connect the speaker cords between the speaker terminals of the Unit and those of the Speakers. • When inserting the speaker wire lead, open the speaker terminal. • Connect the bl ...
-
JVC FS-X3 - page 11
8 Getting Started English Removing the Speaker Grills (SP-FSX1) The speaker grills can be removed. When removing: 1. Pull the bottom towards you with your fingers. 2. Also pull the to p towards you. When attaching the speaker grills: Attach the speaker grills as shown in the diagram . Connecting a Powered Subwoofer Connect a signal cord (n ot suppl ...
-
JVC FS-X3 - page 12
9 Getting Started English Connecting an MD Recorder, etc (Optical Digital Output) Unplug the cap and connect an optical digital cord (not supplied) between the System ’ s OPTICAL DIGITAL OUT terminal and the input terminal of the MD recorder, etc. You can record the digital output signal from the System ’ s CD Player t o the MD recorder, etc. C ...
-
JVC FS-X3 - page 13
10 English Basic Operations Turning the Power On and Off Turning the System On Press the STANDBY/ON button. The display comes on and “ HELLO ” is displayed once. The STANDBY/ON indicator lights in green . The System comes on ready to continue in the mode it was in when the power was last turned off. ❑ For example, if the last thing you were d ...
-
JVC FS-X3 - page 14
11 Basic Operations English Adjusting the Bright ness (DIMMER - at Power On) You can adjust the brightness of the display. When the System is Turned On At power on, each time you press the DIMMER button on the Remote Control, the brightness changes as follows: DIMMER OFF = DIMMER 1 = DIMMER 2 = (back to the beginning) DIMMER OFF : Bright DIMMER 1 : ...
-
JVC FS-X3 - page 15
12 Basic Operations English Tone Control (BASS/TREBLE) You can control the tone by changing the bass (low frequen- cy) and treble (high frequency). On the Remote Control 1 Press the B ASS/TREBLE button. Each time you press the button, the Tone Control mode changes as follows. BASS = TREBLE = Normal display = (back to the beginning) 2 While “ BA S ...
-
JVC FS-X3 - page 16
13 English Using the Tuner You can listen to FM and AM stations. Stati ons can be tuned in manually, automatically, or from preset memo ry storage. ❑ Before listening to the radio: • Make sure that both the FM and AM antennas are cor- rectly connected. (See pages 5 and 6). Setting the AM Tuner Interval Spacing When sh ipped, the AM tuner interv ...
-
JVC FS-X3 - page 17
14 Using the Tuner English ● Preset Tuning using the Remote Control (Possible only after presetting stations) Select the desired preset number using the 3 or 2 button on the Remote Control. The display will show the preset number ’ s band and frequency. • Y ou can also select the desired preset number using the Numeric Ke ys. See “ Entering ...
-
JVC FS-X3 - page 18
15 Using the Tune r English Beat Cut (AM Reception) Switching the Beat Cut mode may reduce beat noise. Each time you press the FM/PLAY MODE button while re- ceiving an AM broadcast, the Beat Cut mode changes as fol- lows. BEAT CUT 1 = BEAT CUT 2 = BEAT CUT 3 = BEAT CUT 4 = (back to the beginning) Set to the position where beat noise is small. • T ...
-
JVC FS-X3 - page 19
16 English Using the CD Player You can use Normal, Random, Program or Repeat Play. Re- peat Play can repeat all the tracks or just one of the tracks on the CD. Here are the basic things you need to know to play a CD and locate the different tracks on it. This Unit has been designed only to playback the fo llow- ing CDs. • Digital audio CD • Rec ...
-
JVC FS-X3 - page 20
17 Using the CD Player English ❑ You can insert a CD while listening to the other source. • Howe ver , while the CD door is operating (opening or closing), the other source will be muted. CAUTI ON: • DO NOT try to open or close the CD door by hands as it will be damaged. To Unload a CD Take out the CD as shown below. Basics of Using the CD Pl ...
-
JVC FS-X3 - page 21
18 Using the CD Player English 5 Press the Numeric Keys to enter the track n umber you want to pr ogram (See page 12). The program order number will be assigned from “ 1 ” , if nothing is programmed yet. Example: • T o dele te the last e ntry , press the C ANCEL butt on. 6 Repeat step 5 to pr ogram the other tracks. You can see the total play ...
-
JVC FS-X3 - page 22
19 Using the CD Player English Repeating Tracks You can repeat all tracks or individual track, as many times as you like. During playback or in Stop mode, press the RE- PEAT button on the Remote Contro l. Each time you press the button, the Repeat mode and Re- peat indicator c hange as follows. CD REPEAT ALL ( ALL) = CD REPEAT 1 ( ) = CD REPEAT OFF ...
-
JVC FS-X3 - page 23
20 English Using External Equipments Listening to External Equipment You can listen to the external equipment such as M D re- corder, tape deck or other auxiliary. ❑ First make sure that the external equipment is properly connected to the System. (See page 8). 1 Set the V OLUME contro l to the mini- mum posit ion. 2 Press the LINE but ton on the ...
-
JVC FS-X3 - page 24
21 Using External Equipments English Recording the System ’ s Source to External Equipment You can record t he System ’ s source to external equipment which is connected to the LINE OUT or OPTICAL DIGI- TAL OUT termin al of the System, such as ta pe deck or MD recorder, etc. ❑ First make sure that the external equipment is properly connected ...
-
JVC FS-X3 - page 25
22 English Using the Timers The timers let you control listening functions automatically. Two types of timers are available: DAILY Timer Use this timer to se t wake up everyday to music from any source, including melodies. SLEEP Timer Fall asleep and have your System turn off automatically after a certain length of time. Setting the Clock When you ...
-
JVC FS-X3 - page 26
23 Using the Timers English 3 Press the SET button. The minute digits of the time in dication blink on the dis- play. • To return to the hour setting, press the CANCEL button. 4 Press the 3 or 2 button to set the minute. 5 Press the SET button. “ ADJUST OK! ” appears on the display. The Clock in- dicator ( ) remains lit. Then, the sele cted t ...
-
JVC FS-X3 - page 27
24 Using the Timers English On the Remote Control 1 Press the CLOCK/TI MER button repeat- edly until “ ON (time) ” appears on the display. At this time, “ DAILY ” indicator blinks on the display. Each time you press the button, the display changes as follows. DAILY ON?/DAILY OFF? = ON (time)* = Clock setting display = Cancelled = (back to t ...
-
JVC FS-X3 - page 28
25 Using the Timers English 5 Setting the volume level. Press the 3 or 2 button to select the vo lume level (VOLUME 1-50), then press the SET button. 6 Select the FADE function. Press the 3 or 2 button to select either “ FADE ” (fades in at power on) or “ NoFADE ” (does not fade in). 7 Press the SET button. The timer setting is comple ted, ...
-
JVC FS-X3 - page 29
26 Using the Timers English Setting the SLEEP Timer Use the Sleep Time r to turn the System off after a certain number of minutes when i t is playing. By setting the Sleep Timer, you can fall asleep to music and know that your Sys- tem will turn off by itself rather than play all night. • You can only set the Sleep Timer when the System is on. On ...
-
JVC FS-X3 - page 30
27 English Troubleshooting • If you are having a problem with your System, check this list for a possible solution before calling for service. • If you cannot solve the problem from the hints giv en here “ ERR OR! ” appears on the display , or the System has been phys- ically damaged, call a qualified person, such as your dealer , for servi ...
-
JVC FS-X3 - page 31
28 English Care And Maintenance Handle your CDs carefully, and they will last a long time. Compact Discs CAUTI ON: • Do not use any sol vent (for example, con- ventional reco rd cleaner, spray thi nner, benzine, etc.) to cle an a CD. General Notes In general, you will have the best perfor mance by keeping your CDs and the mechanism clea n. • St ...
-
JVC FS-X3 - page 32
29 English Specifications CA-FSX1/CA-FSX3 Amplifier Output Power :60 W (30 W + 30 W) at 4 Ω (10% THD) Input Sensiti vity/ Impedance (1 kHz) LINE IN :210 mV/51 k Ω (LEVEL 1) 520 mV/51 k Ω (LEVEL 2) Output Sensiti vity/ Impedance (1 kHz) LINE OUT :600 mV/5.1 k Ω OPTICAL DIGIT AL OUT : – 23 dBm - – 15 dBm Speaker terminals :MIN. 4 Ω Subw ...
-
JVC FS-X3 - page 33
VICT OR COMP ANY OF JAP AN, LIMITED EN, CS 0403MNMCREJEM © 2003 VICT OR COMP ANY OF JAP AN, LIMITED FS-X1-3(US)_E.book Page 30 Friday, April 1 8, 2003 7:27 PM ...
-
JVC FS-X3 - page 34
SP-FSX1 CA-FSX1 SP-FSX1 SP-FSX3 CA-FSX3 SP-FSX3 COMP A CT COMPONENT SYSTEM SISTEMAS DE COMPONENTES COMP A CT OS SISTEMA DE COMPONENTES COMP A CT OS For Customer Use: Enter below the Model No . and Serial No. which are located either on the rear , bot- tom or side of the cabinet. Retain this information for future r eference. M o d e l N o. S e r i ...
-
JVC FS-X3 - page 35
G-1 W arnings, Cautions and Others A visos, precauciones y otras notas Advert ê ncias, Cuidado e outras notas CA U TION T o reduce the risk of e lectrical shocks , fire, etc.: 1. Do not remove scre ws, cov ers or cabinet. 2. Do not expose this appliance to rain or moisture. PRECA U CI Ó N P ara reducir riesgos de choques e léctricos, incendio , ...
-
JVC FS-X3 - page 36
G-2 Caution: Proper V entilation T o avoid risk of electr ic shock and fire, and to pr ev ent damage, loca te the apparatus as follows: 1 F ront: No obstr uctions a nd open spacin g. 2 Sides/ T op/ Back: No ob structio ns should be pl aced in the areas shown by the dimensions below . 3 Bott om: Place on the lev el s urface . Maintain an ad equate a ...
-
JVC FS-X3 - page 37
1 English Introduction Thank you for purchasing the JVC Compact Component System. We hope it will be a valued addition to your home, giving you years of enjoyment. Be sure to read this instruction manual carefully befo re operating your new stereo system. In it you will find all the information you need to set up and use the system. If you have a q ...
-
JVC FS-X3 - page 38
2 Table of Contents English Introduction ................................... ................................................................ ..... 1 Features ............. ................. ................ ................. ................. ................. .................... .. ............... 1 How This Manual Is Organized .... ............ ...
-
JVC FS-X3 - page 39
Table of Contents 3 English Setting the Daily Timer ................. ................. ................. ................... ................. ................. .... 23 Setting the SLEEP Timer .............. ................. ................. ................. ................. ................ ...... .2 6 Timer Priority .... ................. .. ...
-
JVC FS-X3 - page 40
4 English Getting Started Accessories Make sure that you have all of the following items, which are supplied with the System. FM Wire Antenna (1) AM Loop Antenna (1) Remote Control (1) Batteries (2) Speaker Cords (2) AC plug adaptor (1) If any of these items are missing, contact your dealer immediately. How To Put Batteries In t he Remote Control M ...
-
JVC FS-X3 - page 41
5 Getting Started English CAUTI ON: • Make all connecti ons before plugging the Syst em into an AC power outlet. Connecting the FM Antenna Rear Panel of the Center Unit (CA-FSX1/CA-FSX3) Using the Supplied Wire Antenna • Fasten it up in the position until you ha ve the best reception. If reception is poor, connect the outdoor antenna. Using the ...
-
JVC FS-X3 - page 42
6 Getting Started English Connecting the AM Antenna Rear Panel of the Center Unit (CA- FSX1/CA-FSX3) • If the AM loop antenna wire is covered with vinyl, remove the vinyl by twisting it as shown in the diagram. • Make sure the antenna conductors do not t ouch any other terminals, connecting cords and power cord. This could cause poor reception. ...
-
JVC FS-X3 - page 43
7 Getting Started English Connecting the Speakers (SP-FSX1/SP-FSX3) These speakers are exclusively for this system . Using with other devices will damage the speakers. Connect the speaker cords between the speaker terminals of the Unit and those of the Speakers. • When inserting the speaker wire lead, open the speaker terminal. • Connect the bl ...
-
JVC FS-X3 - page 44
8 Getting Started English Removing the Speaker Grills (SP-FSX1) The speaker grills can be removed. When removing: 1. Pull the bottom towards you with your fingers. 2. Also pull the to p towards you. When attaching the speaker grills: Attach the speaker grills as shown in the diagram . Connecting a Powered Subwoofer Connect a signal cord (n ot suppl ...
-
JVC FS-X3 - page 45
9 Getting Started English Connecting an MD Recorder, etc (Optical Digital Output) Unplug the cap and connect an optical digital cord (not supplied) between the System ’ s OPTICAL DIGITAL OUT terminal and the input terminal of the MD recorder, etc. You can record the digital output signal from the System ’ s CD Player t o the MD recorder, etc. C ...
-
JVC FS-X3 - page 46
10 English Basic Operations Turning the Power On and Off Turning the System On Press the STANDBY/ON button. The display comes on and “ HELLO ” is displayed once. The STANDBY/ON indicator lights in green . The System comes on ready to continue in the mode it was in when the power was last turned off. ❑ For example, if the last thing you were d ...
-
JVC FS-X3 - page 47
11 Basic Operations English Adjusting the Bright ness (DIMMER - at Power On) You can adjust the brightness of the display. When the System is Turned On At power on, each time you press the DIMMER button on the Remote Control, the brightness changes as follows: DIMMER OFF = DIMMER 1 = DIMMER 2 = (back to the beginning) DIMMER OFF : Bright DIMMER 1 : ...
-
JVC FS-X3 - page 48
12 Basic Operations English Tone Control (BASS/TREBLE) You can control the tone by changing the bass (low frequen- cy) and treble (high frequency). On the Remote Control 1 Press the B ASS/TREBLE button. Each time you press the button, the Tone Control mode changes as follows. BASS = TREBLE = Normal display = (back to the beginning) 2 While “ BA S ...
-
JVC FS-X3 - page 49
13 English Using the Tuner You can listen to FM and AM stations. Stati ons can be tuned in manually, automatically, or from preset memo ry storage. ❑ Before listening to the radio: • Make sure that both the FM and AM antennas are cor- rectly connected. (See pages 5 and 6). Setting the AM Tuner Interval Spacing When sh ipped, the AM tuner interv ...
-
JVC FS-X3 - page 50
14 Using the Tuner English ● Preset Tuning using the Remote Control (Possible only after presetting stations) Select the desired preset number using the 3 or 2 button on the Remote Control. The display will show the preset number ’ s band and frequency. • Y ou can also select the desired preset number using the Numeric Ke ys. See “ Entering ...
-
JVC FS-X3 - page 51
15 Using the Tune r English Beat Cut (AM Reception) Switching the Beat Cut mode may reduce beat noise. Each time you press the FM/PLAY MODE button while re- ceiving an AM broadcast, the Beat Cut mode changes as fol- lows. BEAT CUT 1 = BEAT CUT 2 = BEAT CUT 3 = BEAT CUT 4 = (back to the beginning) Set to the position where beat noise is small. • T ...
-
JVC FS-X3 - page 52
16 English Using the CD Player You can use Normal, Random, Program or Repeat Play. Re- peat Play can repeat all the tracks or just one of the tracks on the CD. Here are the basic things you need to know to play a CD and locate the different tracks on it. This Unit has been designed only to playback the fo llow- ing CDs. • Digital audio CD • Rec ...
-
JVC FS-X3 - page 53
17 Using the CD Player English ❑ You can insert a CD while listening to the other source. • Howe ver , while the CD door is operating (opening or closing), the other source will be muted. CAUTI ON: • DO NOT try to open or close the CD door by hands as it will be damaged. To Unload a CD Take out the CD as shown below. Basics of Using the CD Pl ...
-
JVC FS-X3 - page 54
18 Using the CD Player English 5 Press the Numeric Keys to enter the track n umber you want to pr ogram (See page 12). The program order number will be assigned from “ 1 ” , if nothing is programmed yet. Example: • T o dele te the last e ntry , press the C ANCEL butt on. 6 Repeat step 5 to pr ogram the other tracks. You can see the total play ...
-
JVC FS-X3 - page 55
19 Using the CD Player English Repeating Tracks You can repeat all tracks or individual track, as many times as you like. During playback or in Stop mode, press the RE- PEAT button on the Remote Contro l. Each time you press the button, the Repeat mode and Re- peat indicator c hange as follows. CD REPEAT ALL ( ALL) = CD REPEAT 1 ( ) = CD REPEAT OFF ...
-
JVC FS-X3 - page 56
20 English Using External Equipments Listening to External Equipment You can listen to the external equipment such as M D re- corder, tape deck or other auxiliary. ❑ First make sure that the external equipment is properly connected to the System. (See page 8). 1 Set the V OLUME contro l to the mini- mum posit ion. 2 Press the LINE but ton on the ...
-
JVC FS-X3 - page 57
21 Using External Equipments English Recording the System ’ s Source to External Equipment You can record t he System ’ s source to external equipment which is connected to the LINE OUT or OPTICAL DIGI- TAL OUT termin al of the System, such as ta pe deck or MD recorder, etc. ❑ First make sure that the external equipment is properly connected ...
-
JVC FS-X3 - page 58
22 English Using the Timers The timers let you control listening functions automatically. Two types of timers are available: DAILY Timer Use this timer to se t wake up everyday to music from any source, including melodies. SLEEP Timer Fall asleep and have your System turn off automatically after a certain length of time. Setting the Clock When you ...
-
JVC FS-X3 - page 59
23 Using the Timers English 3 Press the SET button. The minute digits of the time in dication blink on the dis- play. • To return to the hour setting, press the CANCEL button. 4 Press the 3 or 2 button to set the minute. 5 Press the SET button. “ ADJUST OK! ” appears on the display. The Clock in- dicator ( ) remains lit. Then, the sele cted t ...
-
JVC FS-X3 - page 60
24 Using the Timers English On the Remote Control 1 Press the CLOCK/TI MER button repeat- edly until “ ON (time) ” appears on the display. At this time, “ DAILY ” indicator blinks on the display. Each time you press the button, the display changes as follows. DAILY ON?/DAILY OFF? = ON (time)* = Clock setting display = Cancelled = (back to t ...
-
JVC FS-X3 - page 61
25 Using the Timers English 5 Setting the volume level. Press the 3 or 2 button to select the vo lume level (VOLUME 1-50), then press the SET button. 6 Select the FADE function. Press the 3 or 2 button to select either “ FADE ” (fades in at power on) or “ NoFADE ” (does not fade in). 7 Press the SET button. The timer setting is comple ted, ...
-
JVC FS-X3 - page 62
26 Using the Timers English Setting the SLEEP Timer Use the Sleep Time r to turn the System off after a certain number of minutes when i t is playing. By setting the Sleep Timer, you can fall asleep to music and know that your Sys- tem will turn off by itself rather than play all night. • You can only set the Sleep Timer when the System is on. On ...
-
JVC FS-X3 - page 63
27 English Troubleshooting • If you are having a problem with your System, check this list for a possible solution before calling for service. • If you cannot solve the problem from the hints giv en here “ ERR OR! ” appears on the display , or the System has been phys- ically damaged, call a qualified person, such as your dealer , for servi ...
-
JVC FS-X3 - page 64
28 English Care And Maintenance Handle your CDs carefully, and they will last a long time. Compact Discs CAUTI ON: • Do not use any sol vent (for example, con- ventional reco rd cleaner, spray thi nner, benzine, etc.) to cle an a CD. General Notes In general, you will have the best perfor mance by keeping your CDs and the mechanism clea n. • St ...
-
JVC FS-X3 - page 65
29 English Specifications CA-FSX1/CA-FSX3 Amplifier Output Power :60 W (30 W + 30 W) at 4 Ω (10% THD) Input Sensiti vity/ Impedance (1 kHz) LINE IN :210 mV/51 k Ω (LEVEL 1) 520 mV/51 k Ω (LEVEL 2) Output Sensiti vity/ Impedance (1 kHz) LINE OUT :600 mV/5.1 k Ω OPTICAL DIGIT AL OUT :–23 dBm - –15 dBm Speaker terminals :MIN. 4 Ω Subwoof ...
-
JVC FS-X3 - page 66
VICT OR COMP ANY OF JAP AN, LIMITED EN, SP , PR 0503MNMCREJEM © 2003 VICT OR COMP ANY OF JAP AN, LIMITED FS-X1-3(UW)_E.book Page 30 Thur sday, April 10, 2003 4:06 PM ...
¿Tienes una pregunta acerca de JVC FS-X3?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con JVC FS-X3, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con JVC FS-X3 probablemente compartirá una forma de solucionarlo.