-
Craftsman 3BS12401 - page 1
Owner's Manui ® 1 HP (Max. Developed) 2 Speeds 1410 and 2600 F.P.IVI. (No Load) Leg Stand SAW Model No. 137.224320 E82358 37J5 LISTED CAUTION: Before using th!s band saw, read this manual and follow all its Safety Rules and Operating Instructions. ® Safety Instructions • Installation • Operation ,, Maintenance o Parts List Customer Help ...
-
Craftsman 3BS12401 - page 2
SECTION PAGE Warranty ......... .............. ......................................... 2 Product Specifications ..................................................... 2 Safety Instructions ........................................................ 3 Accessories and Attachments ............................................... 6 Carton Contents ....... ...
-
Craftsman 3BS12401 - page 3
24. DO NOT operate the tool if you are under the influence 14. CUT only one workpiece at a time. Make sure the table of any drugs, alcohol or medication thatcould affect your is clear of everything except the workpiece and its ability to use the tool properly, guides before you turn the saw on. 25. ALWAYS operate the band saw in a well-ventilated a ...
-
Craftsman 3BS12401 - page 4
Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas. (when using 120 volts only) Ampere Rating more qhan not more th;_n 0 6 6 10 10 12 12 16 Totalle ...
-
Craftsman 3BS12401 - page 5
Upper cover ON/OFF switch Lower cover Motor pulley Mounting holes Blade tension knob "blade wheel guard Lower blade support bearing Lower blade guide 3er blade support bearing Upper blade guide Table insert Miter gauge -- Table aligning pin bevel scale Lower blade wheel V-Belt Upper blade guide lock knob Upper blade guide red Blade Miter slot ...
-
Craftsman 3BS12401 - page 6
Phillips screwdriver ASSEMBLY iNSTRUCTiONS TOOLS NEEDED . v(" _ _Ipl,l,l,l,_ Combination square _l_j41'l_l'l'('l ' I'1' ' Adjustable wrench Straight edge _) Feeler gauge - size 0.02 For your safety, never connect plug to power source receptacle until all assembly and adjustment steps are completed, and y ...
-
Craftsman 3BS12401 - page 7
INSTALLING AND REMOVING BLADES (FIG. H) To avoid injury from accidental starting, always turn the switch OFF and remove the plug from the power source before moving, replacing, or adjusting the blade. Removing 1. Loosen the blade tension by turning the blade tension knob (1) counterclockwise. 2. Remove the table insert (2) and remove the table alig ...
-
Craftsman 3BS12401 - page 8
BLADE TENSION (FIG. M) To avoid injury, turn the switch OFF and disconnect the saw from the power source before rnaking any adjustments, NEVER make tension adjustments with the machine running. The gauge (1) on the bracket (2) at the rear of the upper wheel housing indicates the proper tension for the various blade widths. 1. Set the blade tension ...
-
Craftsman 3BS12401 - page 9
Support bearing (FIG. S) 6. Loosen the bearing hex socket screw (7) with the hex wrench. 7. Move the blade support bearing shaft (8) in or out until the support bearing (9) is 1/64" behind the saw blade. 8. Tighten the bearing hex socket screw. BASIC SAW OPERATIONS FIG. S 9 8 ON / OFF SWITCH (FIG. U) The keyed switch is intended to prevent una ...
-
Craftsman 3BS12401 - page 10
CHANGING SPEED SE'I-FING (FIG.Y) To avoid injury, turn the switch OFF and disconnect the saw from the power source before making any adjustments. NEVER make adjustments with the machine running. 1. Loosen the belt tension by turning the tension lock handle (6). 2. Open the lower wheel cover and reposition the V-belt (3). A. Changing the speed ...
-
Craftsman 3BS12401 - page 11
MOTOR TROUBLESHOOTING GUIDE , To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before making any adjustments. + All electrical or mechanical repairs should be done only by qualified service technicians• Contact the nearest Sears Service Center. GENERAL Problem Blade does not run in the ...
-
Craftsman 3BS12401 - page 12
CRAFTSMAN 12" BAND SAW 137.224320 o When servicing use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause product damage• + Any attempt to repair or replace electrical parts on this band saw may create a HAZARD unless repair is done by a qualified service technician. Repair service is available at your near ...
-
Craftsman 3BS12401 - page 13
CRAFTSMAN 12" BAND SAW PARTS LIST FOR FIGURE B o #. o _, GI #. I I I I I I I I I I i ,t--- d i 1 w _ O,"T" z G.. ;> F- bg 9 z _zZ_Z_ a__omz i 0 _ I04 (M I I I o',lo -_lCq 1 1 1 1 1 1.1.1 _ u_ 0,o "rl_ Z 7_ . _ _Ix cc r_ rr" _ LU I o,S N o0,_ o N NI_ I I O3 1 137.224320 CRAFTSMAN 12" BAND SAW FIGURE B 121 ( 86 / ...
-
Craftsman 3BS12401 - page 14
STAND PARTS LIST FOR FIGURE C 137.224320 STAND FIGURE C 137.224320 Key Part No. Description Qty 1 3BS40101 Stand top plate 1 2 3BS40201 Lower bracket (long) 2 3 3BS40301 Lower bracket (short) 2 4 3BS40401 Leg 4 5 3BS40501 Miter gauge storage 1 6 3BS40601 Screw 2 7 3BS40701 Nut 32 8 3BS40801 Flat washer 32 9 3BS40901 Screw 32 10 3BS41001 Pad 4 1 o J ...
¿Tienes una pregunta acerca de Craftsman 3BS12401?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Craftsman 3BS12401, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Craftsman 3BS12401 probablemente compartirá una forma de solucionarlo.