-
Hunter Hudson - page 1
www .HunterF an.com 1.888.830.1326 PA G E 7 PA G E 13 PA G E 10 PA G E 5 PA G E 6 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed Wiring Canop y Maintenanc e & Cleaning Blades T roubleshooting Downrod Swit ch Housing Prepar ation T able of C ontents PA G E 11 PA G E 12 Congratulati ...
-
Hunter Hudson - page 2
www .HunterF an.com 1.888.830.1326 M0048-01 • 12/18/12 • © Hunter F an Company 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring, use a qualied electrician. Y ou may need a friend to help you. Check box to see fan weight Assess location 30 inches from blade tip to neare ...
-
Hunter Hudson - page 3
www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools . 3 M0048-01 • 12/18/12 • © Hunter F an Company ...
-
Hunter Hudson - page 4
www .HunterF an.com 1.888.830.1326 4 M0048-01 • 12/18/12 • © Hunter F an Company 1.866.268.1936 If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) . Guide T ouches BOTH Ceiling & Wa ll S I T U A T ...
-
Hunter Hudson - page 5
1.888.830.1326 www .HunterF an.com C eiling Bracket OFF Make sure all four (4) bumpers are still attached . F or angled ceilings, point opening toward peak. Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the ...
-
Hunter Hudson - page 6
www .HunterF an.com 1.888.830.1326 C eiling Bracket (c ontinued) Prepar ation 1.888.830.1326 www .HunterF an.com D I S C A R D K E E P ! Remove the shipping blocks from the motor . Sav e the screws . They will be needed for blade iron installation. Time Sav er Tip: Get a helper to insert grommets, found in the hardware bag , into the blades while y ...
-
Hunter Hudson - page 7
1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to next page If you need a diff erent downrod length follo w these steps: Ste ...
-
Hunter Hudson - page 8
KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downr od. Downrod (c ontinued) 8” 3/8” Tighten the setscrew with pliers. DO N ...
-
Hunter Hudson - page 9
1.888.830.1326 9 M0048-01 • 12/18/12 • © Hunter F an Company www .HunterF an.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canop y sit loosely on top of the fan. ...
-
Hunter Hudson - page 10
www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , downrod, and hanging bracket. (Grounding) Green/Y ellow Stripe Green/Y ellow Stripe Wh ...
-
Hunter Hudson - page 11
www .HunterF an.com 1.888.830.1326 11 M0048-01 • 12/18/12 • © Hunter F an Company Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown. Screw Holes Insert the two canopy screws found in the hardwar e bag. No te: Fan sty ...
-
Hunter Hudson - page 12
www .HunterF an.com 1.888.830.1326 M0048-01 • 12/18/12 • © Hunter F an Company Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes. 12 Insert grommets found in the hardware bag i ...
-
Hunter Hudson - page 13
www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfwa y into the motor housing . I t does not matter which two screw holes you choose . Insert the third screw ...
-
Hunter Hudson - page 14
www .HunterF an.com 1.888.830.1326 S witch Housing (continued) Make sure the lower switch housing is securely attached to the upper switch housing. F ailure to properly secur e all three assembly screws could result in the light xture falling. Connect the plugs from the upper and lower switch housings . Mak e sure to line up the colored markings ...
-
Hunter Hudson - page 15
www .HunterF an.com 1.888.830.1326 M0048-01 • 12/18/12 • © Hunter F an Company 15 Maintenanc e & Cleaning ON T urn P ower Changing the direction of air ow - move the reverse switch to the opposite position. Cleaning the fan - use soft brushes or cloths to prevent scratching . Cleaning products may damage the nishes. Reverse Switch C ...
-
Hunter Hudson - page 16
www .HunterF an.com 1.888.830.1326 M0048-01 • 12/18/12 • © Hunter F an Company 16 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • T urn the power off , support the fan carefully , and check that the hanger ball is properly seated . • Use the provided balancing kit and instruc ...
¿Tienes una pregunta acerca de Hunter Hudson?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hunter Hudson, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hunter Hudson probablemente compartirá una forma de solucionarlo.