-
Makita 2106K - page 1
Portable Band Saw -~ ~ ~ Max. cutting capacity Round Rectangular workpiece workpiece Without optional stand With optional stand 115 mm dia. 115 mm x 115 mm 75 mm x 110 mm 14-112") 14-1/2" x 4-112") (3" x 4-3/8") MODEL 2106 MODEL 2106K Wlth Steel Carrylnlpcase Blade speed No load surface (FPM) High Low 260 200 INSTRUCTION MA ...
-
Makita 2106K - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. ...
-
Makita 2106K - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don‘t carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an ...
-
Makita 2106K - page 4
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T ...
-
Makita 2106K - page 5
Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. I Lock button 1 1 1 Trigger switch CAUTION : Before plugging in the tool, always check to see that the ...
-
Makita 2106K - page 6
Installing or removing blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. Oil on the blade can cause the blade to slip or come off unexpectedly. Wipe off all ex- cess oil with a cloth before installing the blade. 0 Use caution when handling the blades so that you are not cut by their ...
-
Makita 2106K - page 7
Position the blade around the wheels and insert the other side of the blade within the Hold the blade in place and turn the blade tightening lever counterclockwise until it hits against the protrusion on the frame. This places proper tension on the blade. Make sure that the blade is correctly positioned within the blade guard and around the wheels. ...
-
Makita 2106K - page 8
Squaring blade with stopper plate Use the triangular rule to make sure that the side of the blade is square with the side of the stopper plate. If not square, loosen the bolts securing the stopper plate and adjust the stopper plate accordingly. Triangular rule Cutting lubricant When cutting metals, use Makita cutting wax as a cutting lubricant. To ...
-
Makita 2106K - page 9
Hold the tool as shown in the figure with the stopper plate contacting the workpiece and the blade clear of the workpiece. Turn the tool on and wait until the blade attains full speed. Gently lower the blade into the cut. The weight of the tool or slightly pressing the tool down will supply adequate pressure for the cutting. Do not force the tool. ...
-
Makita 2106K - page 10
MA1 NTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning After use, remove wax, chips and dust from the tool, wheel tires and blade. CAUTION : 0 Never use solvents such as turpentine, gasoline, lacquer, etc. to clean plastic parts. 0 Wax and chips on the tires ...
-
Makita 2106K - page 11
Use a screwdriver to remove the brush I holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. Brush holder cap To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement pa ...
-
Makita 2106K - page 12
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Band saw blade 44-718" x 112" x .0 ...
-
Makita 2106K - page 13
Cutting wax Part No. 191897-9 Portable band saw stand Part No. 122370-8 (For accurate square cutting operations) Steel carrying case Part No. 823204-5 13 ...
-
Makita 2106K - page 14
Feb.-04-'88 EN PORTABLE BAND SAW Model 2106 Note: The switch, noise suppressor and other part configurations may differ from country to country. 14 ...
-
Makita 2106K - page 15
MODEL 2106 Feb.-04-'BB US MACHlNE 50 51 52 53 54 55 56 57 58 59 60 61 62 63 641 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 BO 81 82 83 84 85 86 87 89 90 91 93 94 95 96 97 98 a8 'EM DESCRIPTION 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 2 2 1 1 2 1 1 1 1 1 1 2 1 1 1 5 'LtM ,& DESCRIPTION 10 11 MACHINE 112 22 3 ...
-
Makita 2106K - page 16
MAKCTA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freight ...
¿Tienes una pregunta acerca de Makita 2106K?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 2106K, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 2106K probablemente compartirá una forma de solucionarlo.