-
Perle Systems CM-110-XXXXX - page 1
P/N 5500307-15 Perle 10/100 Ethernet Media Convert er Module Installation Guide C-110-XX XXX Unm anaged Module CM-110-XX XXX Managed Modu le ...
-
Perle Systems CM-110-XXXXX - page 2
Perle 10/100 Media Converter M odule – Installation Guide 2 Over vie w This docum ent contains instructions n ecessar y for the instal lation and operation of the Perle 10/1 00 Ethernet M edia Con verter Modul e(s) (C- 110 and CM-11 0) that are us ed in conjunc tion with a P erle MCR Ch assis. The C- 110 are unm anaged m edia converter m odules, ...
-
Perle Systems CM-110-XXXXX - page 3
Perle 10/100 Media Converter M odule – Installation Guide 3 Installatio n The m odule comes equi pped with a ba nk of DIP switches an d jum pers for setting conf iguration. The default d ip switch set tings (all s witches in the UP position) and default jum per settings will work for mos t installations. The f ollowing steps are used to co nfigur ...
-
Perle Systems CM-110-XXXXX - page 4
Perle 10/100 Media Converter M odule – Installation Guide 4 Auto-Config Jumper (CM-110 only ) The Auto-Co nfig jum per (J6) is located jus t belo w the Auto-MDIX jumper ( see above). Ref er to the diagram below f or labelling. T his jumper onl y applies to CM- 110 m odules. Strapping p ins 1 and 2 of the jum per will set the m odule in SW m ode a ...
-
Perle Systems CM-110-XXXXX - page 5
Perle 10/100 Media Converter M odule – Installation Guide 5 DIP Switches DIP Switch Settings Auto Negoti ation (Sw itch 1) Switch Posit ion Mode Up (defau lt) Auto Down Off Note: Auto ne gotiation s hould onl y be turned of f, if the copper link partner does n ot support Auto Negot iation or fix ed settings ar e required b y the copper link partn ...
-
Perle Systems CM-110-XXXXX - page 6
Perle 10/100 Media Converter M odule – Installation Guide 6 Converter M odule will be determ ined by the Du plex (switch 4) and Speed (s witch 5) dip s witch settings . Link M ode (Switch 2) Switch Posit ion Mode Up (defau lt) Link Pass- Through Mode Down Standard Mo de Link Pass-T hrough: In this mode, the l ink state on one connec tion is direc ...
-
Perle Systems CM-110-XXXXX - page 7
Perle 10/100 Media Converter M odule – Installation Guide 7 fiber link on either the tra nsm it or receive line will b e passed throu gh to the local co pper connec tion thus notifying the c onnected de vice. If the Media C onverter has been set to Link Pass -Through m ode, the effec t will be the sam e as FEF, since the link loss on the fiber re ...
-
Perle Systems CM-110-XXXXX - page 8
Perle 10/100 Media Converter M odule – Installation Guide 8 Duplex (copp er) (Sw itch 4) Switch Posit ion Mode Up (defau lt) Full Down Half Note: W hen Auto Negoti ation (SW 1) is set to Of f, the Media Converter will use this D uplex settin g for its copp er connectio n. Up: T he Media Converter Module wi ll be set to Fu ll Duplex m ode. Dow n: ...
-
Perle Systems CM-110-XXXXX - page 9
Perle 10/100 Media Converter M odule – Installation Guide 9 Duplex (fiber) ( Swit ch 6) Switch Posit ion Mode Up (defau lt) Full Down Half Up: T he Media Converter Module’s f iber link wil l be set to F ull Duplex Mode. Dow n: The Media Conv erter Module’s f iber will be s et to Half D uplex Mode. Loopback (Sw itch 7 Switch Pos ition Mode Up ...
-
Perle Systems CM-110-XXXXX - page 10
Perle 10/100 Media Converter M odule – Installation Guide 10 Installing or Replacing Media Converter Modules Caution: O bserve electro static dis charge precau tions wh en installing the Media Con verter Module(s) into th e Chassis. Failure to obs erve this caution co uld result in d amage to t he Media Convert er M odul e(s) and /o r chassis. Th ...
-
Perle Systems CM-110-XXXXX - page 11
Perle 10/100 Media Converter M odule – Installation Guide 11 6. Tighten the ca ptive retai ner scr ew to ensure the Me dia Converter M odule is loc ked in place . 7. Rem ove the dust cap f rom the fiber c onnector and connect th e fiber and copp er cables . Removing Media Convert Modules 1. Loosen the c aptive retain er screw on th e front of the ...
-
Perle Systems CM-110-XXXXX - page 12
Perle 10/100 Media Converter M odule – Installation Guide 12 • Connect the fiber cable f rom one Medi a Converter M odule to the other Media C onverter/s witch/f iber device. Installing the Copper Cable • Locate 10/100 Base-T compliant copper c ables with male, RJ- 45 connectors installed at both ends . • Connect the RJ-45 cable between th ...
-
Perle Systems CM-110-XXXXX - page 13
Perle 10/100 Media Converter M odule – Installation Guide 13 Operation Status LED The Perle 10/ 100 Etherne t Media C onverter Mod ules have six s ingle color status LEDs located on t he face plate of the m odule. PWR On – Power is on; mod ule is operating normal ly Blinking (slow ) – The module is in Loopback mode . Blinking (fast) – The m ...
-
Perle Systems CM-110-XXXXX - page 14
Perle 10/100 Media Converter M odule – Installation Guide 14 Other Features Auto-M DIX: Auto-MDIX ( autom atic medium- dependant interf ace crossover) detects the s ignalling on the 10/100 BASE-T interface to det erm ine the type of c able connec ted (straight-thr ough or cros sover) and automatical ly configures t he conn ection. Error Recov ery ...
-
Perle Systems CM-110-XXXXX - page 15
Perle 10/100 Media Converter M odule – Installation Guide 15 Troubleshooting General • Ensure that the Me dia Converter Module is s ecurely s eated in the chassis. T he PWR LED s hould be on. • Ensure both devices on either end of the fib er are com patible. If using a sim plex fiber con nection, ens ure that you have both an Upstream (U) and ...
-
Perle Systems CM-110-XXXXX - page 16
Perle 10/100 Media Converter M odule – Installation Guide 16 Method 2: The f iber connection ca n also be verified b y configuring the r emote Media Con verter for loop back m ode. The LKF L EDs on both Media Con verters should be lit. Data s hould pas s through t he local converter, o ver the fiber co nnection to th e rem ote Media Converter. At ...
-
Perle Systems CM-110-XXXXX - page 17
Perle 10/100 Media Converter M odule – Installation Guide 17 Technical Specifications Power Inpu t/Consumpt ion 12V DC / 2.1 W Operating T emperatur e: 0 °C to 50 °C (32 °F to 122 ° F) Storage Tem perature: - 25 °C to 70 °C (-13 °F to 15 8 °F) Operating Hu midity: 5% to 90% non-condensing Storage Hum idity: 5% to 95% non-condensing Operat ...
-
Perle Systems CM-110-XXXXX - page 18
Perle 10/100 Media Converter M odule – Installation Guide 18 C-110-S2ST120 CM-110-S2ST120 S M TX: 1550 RX: 1550 M in: 0 Max: 5 Min: -35 Max: 0 35 C-110-S2LC120 CM-110-S2LC120 SM TX: 15 50 RX: 1550 M in: 0 Max: 5 Min: -35 Max: -3 35 C-110-S1SC20U CM-110-S1SC20U SM TX: 1310 RX: 1550 M in: -14 Max: -8 Min: -32 Max: -3 18 C-110-S1SC20D CM-110-S1SC20D ...
-
Perle Systems CM-110-XXXXX - page 19
Perle 10/100 Media Converter M odule – Installation Guide 19 Compliance Information FCC This product has been found to comply with the li mits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against har mful interference when the equip ment is operated in a commercial ...
-
Perle Systems CM-110-XXXXX - page 20
Perle 10/100 Media Converter M odule – Installation Guide 20 Warranty / Reg istration Perle’s stan dard Lifetim e Warrant y provides cus tomers with r eturn to factor y repa irs for Perle products that fail under the condit ions of the warrant y coverage. Detai ls can be fou nd at: http://www.pe rle.com/support_services/warrant y .shtml Contact ...
¿Tienes una pregunta acerca de Perle Systems CM-110-XXXXX?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Perle Systems CM-110-XXXXX, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Perle Systems CM-110-XXXXX probablemente compartirá una forma de solucionarlo.