-
GE 131-10595-2 1-07 JR - page 1
1 31-10595-2 1-07 JR BEFORE YOU BEGIN Read these instructions carefully and completely . • IMPOR T ANT — Save these instructions for local inspector’ s use. • IMPOR T ANT — Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the consumer . • Note to Consumer – Keep these instr ...
-
GE 131-10595-2 1-07 JR - page 2
FOR YOUR SAFETY W ARNING: For personal safety , remove house fuse or open circuit breaker before beginning installation. Failure to do so could result in serious injury or death. • All rough-in and spacing dimensions must be met for safe use of your range. • T o reduce the risk of burns or fire when reaching over hot surface elements, cabinet s ...
-
GE 131-10595-2 1-07 JR - page 3
• Place hands on both sides of the door , and close the oven door to the removal position. This is half way between the broil stop and fully closed. • Lift door up and out until the hinge arms clear the slots. NOTE: The oven door is very heavy . Be sure you have a firm grip before lifting the oven door off the hinges. Use caution once the door ...
-
GE 131-10595-2 1-07 JR - page 4
PRE-INST ALLA TION CUTOUT AND REQUIRED CLEARANCES If cabinets are placed less than 30” min. above the range, see alternate construction. 30” ranges conform to U.L. requirements for 0” spacing from vertical walls below countertops. Allow 1/4” minimum clearance at the back wall above the countertop. W all coverings, counters and cabinets arou ...
-
GE 131-10595-2 1-07 JR - page 5
The Standard Installation of this Drop-In Range is to hang by the countertop on the side metal flanges under cooktop. This Range must not be installed on a base or sub structure (2”x 4” support). If the construction of your cabinet cannot provide a 1/4” flat area at the back of the countertop opening, consider changing the countertop to accom ...
-
GE 131-10595-2 1-07 JR - page 6
Remove house fuse or open circuit breaker . Loosen screws for the junction box cover and rotate out of place or remove the cover . Examine the junction box location to determine the best routing of the conduit, and select the best available 7/8” diameter knockout. A void using holes in the top of the junction box to prevent the conduit from inter ...
-
GE 131-10595-2 1-07 JR - page 7
THREE-CONDUCTOR BRANCH CIRCUIT CONNECTION When connecting to a 3-conductor branch circuit, if local codes permit: Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using wire nuts. Connect the oven red lead to the branch circuit red lead, and the oven black lead to t ...
-
GE 131-10595-2 1-07 JR - page 8
Do not shorten the flexible conduit. The conduit strain relief clamp must be securely attached to the junction box and the flexible conduit must be securely attached to the clamp. If the flexible conduit will not fit within the junction box, do not install the oven until a clamp of the proper size is obtained. NOTE TO ELECTRICIAN: The 3 power leads ...
-
GE 131-10595-2 1-07 JR - page 9
Select the proper position for the countertop thickness and move bracket to proper position. (Unit is supplied with bracket in position 1.) INST ALL THE RANGE INST ALLING THE ANTI-TIP BRACKET The anti-tip bracket is attached to the back of the Drop-In Range. It is designed to fit under the bottom of the countertop opening at the rear . Measure coun ...
-
GE 131-10595-2 1-07 JR - page 10
INST ALL THE RANGE (CONT .) Carefully mark the cabinet for the location of the stop screws. Drill 1/8” pilot holes into the cabinet, each side of the range. (Make sure not to drill entirely through the cabinet wall.) Carefully turn the shoulder screws into the pilot holes until they are tight. INST ALL STOP SCREW These screws prevent the range fr ...
-
GE 131-10595-2 1-07 JR - page 11
A TT ACH THE LOWER TRIM Attach the lower trim (supplied separately with the range) to the bottom of the vertical side trim with the 2 screws supplied. 5 CHECK FOR PROPER INST ALLA TION OF THE STOP SCREW Look at both sides of the range under the door . The stop screws must be located in the notch on the sides of the range, and not touch the top of t ...
-
GE 131-10595-2 1-07 JR - page 12
Lift the oven door by placing one hand on each side. The door is heavy , so you may need help. Do not lift the door by the handle. With the door at the same angle as the removal position (halfway between the closed and broil stop position, seat the notch of the hinge arm into the bottom edge of the hinge slot. The notch of the hinge arm must be ful ...
-
GE 131-10595-2 1-07 JR - page 13
FINAL CHECKLIST • Check to make sure the circuit breaker is closed (Reset) or the circuit fuses are replaced. • Be sure power is in service to the building. • Check to be sure that all packing materials and tape on metal panel (if applicable) under control knobs and drawer have been removed. 12 OPERA TION CHECKLIST • Check to make sure the ...
-
GE 131-10595-2 1-07 JR - page 14
W all Must be flat Must be flat Must be level Must be level 30” smooth cut 9/16” 9/16” 25” AL TERNA TE CONSTRUCTION PREP ARA TION Refer to the Filler or Backguard Kit instructions for Installation details. OPTIONAL MAINTOP FILLER OR BACKGUARD KIT If counter opening extends to the wall, it will require Maintop Filler Kit (JXS66XX) or Backgua ...
-
GE 131-10595-2 1-07 JR - page 15
15 Notes ...
-
GE 131-10595-2 1-07 JR - page 16
Printed in the United States 16 Notes ...
¿Tienes una pregunta acerca de GE 131-10595-2 1-07 JR?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con GE 131-10595-2 1-07 JR, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con GE 131-10595-2 1-07 JR probablemente compartirá una forma de solucionarlo.