Español dropdown-ico

Manual de instrucciones Huffy 21168202

28 de páginas 2.27 mb
Descargar

Pasar a la página of 28

Summary
  • Huffy 21168202 - page 1

    1 10/04 P/N 211682 02 © COPYRIGHT 2004 by HUFFY SPORTS Inground System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. • 2 People • Carpenter’s Level • 15’ Tape Measure • Shovel & Post Hole Digger • Wood Board (scrap) • Tape • Sawhorse or Support Table • Wedge • ...

  • Huffy 21168202 - page 2

    2 P/N 211682 02 10/04 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. T est-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from hol ...

  • Huffy 21168202 - page 3

    10/04 P/N 211682 02 3 SAFETY INSTRUCTIONS Most injuries are caused by misuse and/or not following instructions. Use caution when using this system. • If using a ladder during assembly , use extreme caution. • T wo (2) people are reccomended for this operation. • Seat the pole sections properly . Failure to do so could allow the pole sections ...

  • Huffy 21168202 - page 4

    4 P/N 211682 02 10/04 For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p arts are p acked inside. NOTICE T O ASSEMBLERS ALL Huffy Sport s Bas ...

  • Huffy 21168202 - page 5

    10/04 P/N 211682 02 5 #8 (9)* #10 (4) HARDW ARE IDENTIFIER (BOL TS & SCREWS) HARDW ARE IDENTIFIER (NUTS & W ASHERS) HARDW ARE IDENTIFIER (MET AL SP ACERS) #13 (2) #7 (2) #1 1 (4) #15 (3)* #20 (2) #24 (6) #21 (1) #31 (2) #27 (6) #42 (1) #46 (1) #45 (1) #9 (3)* * You may have extra parts with this model. #47 (4) #48 (1) #49 (1) #53 (4) ...

  • Huffy 21168202 - page 6

    6 P/N 211682 02 10/04 #44 (1) #41 (1) #43 (1) HARDW ARE IDENTIFIER (PLASTIC SP ACERS & CLIPS) HARDW ARE IDENTIFIER (OTHER) #23 (4) #22 (4) #12 (2) #39 (2) #33 (12)* #52 (2) ...

  • Huffy 21168202 - page 7

    10/04 P/N 211682 02 7 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION A: ASSEMBLE THE POLE Phillips-Head Screwdriver (2) 1/2” and (2) 9/16" Wrenches 9/16” 1/2” AND/OR (2) Socket Wrenches and Sockets Shovel and Post Hole Digger Carpenter's Level Tape #7 #15 #20 #21 #9 #8 #11 #13 #12 Container ...

  • Huffy 21168202 - page 8

    8 P/N 211682 02 10/04 1 TO P MIDDLE BOTT OM 2 3 1. Mark pole sections with tape (not supplied) at indicated dist ances from ends as shown. T ape (Not Supplied) 18" (42.7 cm) 6" (15.2 cm) 24" (61 cm) PLAYING SURFACE GROUND SURFACE 2. Ensure ground is level with playing surface, then dig pole hole. CONTACT UTILITIES BEFORE DIGGING. W A ...

  • Huffy 21168202 - page 9

    10/04 P/N 211682 02 9 4. 1" (2.54 cm) SIDE VIEW Fill hole approximately 1/3 full with mixed concrete. FIG . A FLANGE Insert ground sleeve assembly and center in hole ( FIG . A ). Note : Leave 1" below flange exposed for drainage hill. 5. IMPORT ANT!: NOTE POSITION OF FLANGE IMPORT ANT!: CONTINUE ON T O NEXT STEP . DO NOT W AIT FOR CONCRET ...

  • Huffy 21168202 - page 10

    10 P/N 211682 02 10/04 4 3 Fill hole completely with concrete. 6. 1" (2.54 cm) 5 1 " (2.54 cm) 7. T amp down concrete to release air pockets and build drainage hill. Level pole section in all directions several times while concrete is curing. 1" (2.54 cm) SIDE VIEW DRAINAGE HILL IMPORT ANT!: CONTINUE ON T O NEXT STEP . DO NOT W AIT F ...

  • Huffy 21168202 - page 11

    10/04 P/N 211682 02 11 Af ter concrete has cured, remove bottom pole section from ground sleeve (4). Place anti-skid t ape (36) around the bottom area of bottom pole (see note A). KEEP GROUND SLEEVE CAP ON BOTTOM POLE. 36 4 8. 5 Place top edge of anti-skid tape on mark made in step 7. NOTE A: T ape prevent s the pole from rotating during play . NOT ...

  • Huffy 21168202 - page 12

    12 P/N 211682 02 10/04 1 5 9. S tack and bounce bottom (3) and middle (2) pole sections together . Bounce pole sections together until middle section no longer moves toward taped reference mark on bottom pole. 2 IMPORTANT 5 Keep on Bottom Pole 3 Wood Scrap (NOT SUPPLIED) 10. S tack upper pole section (1) to bottom and middle pole assembly and conti ...

  • Huffy 21168202 - page 13

    10/04 P/N 211682 02 13 1 40 7 7 FRONT SIDE 11 . Install pole mount bracket (6) and bracket reinforcement (40) with carriage bolts (7) as shown. T ighten flange nuts (8) completely . 6 8 FRONT SIDE ...

  • Huffy 21168202 - page 14

    14 P/N 211682 02 10/04 12 6 12 13 13 11 9 10 10 12. 6 8 14 14 17 15 13. Attach sp acers (12, 13) to pole mount bracket (6) with bolts (9), washers (10), and nuts (1 1) as shown. Assemble lanyard (17) to locking pin (16) as shown. Attach covers (14) onto pole mount bracket (6) with carriage bolt (15) and nut (8) as shown. DO NOT OVERTIGHTEN 16 IMPOR ...

  • Huffy 21168202 - page 15

    10/04 P/N 211682 02 15 20 19 38 37 21 18 14. 20 15. 16 Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (16). Apply logo and height indicator labels (19) to adjustment rod (18) as shown. Attach handle p arts (37, 38) to adjustment rod with screw (21), carriage bolt (20), an ...

  • Huffy 21168202 - page 16

    16 P/N 211682 02 10/04 SECTION B: ASSEMBLE THE ELEV A T OR TUBES T O BACKBOARD 30 Upper Elevator tube 28 Identify elevator tubes (28 & 30). 9/16” 3/4” 1/2” (2) Wrenches 1/2", (2), 9/16"" and (2) 3/4" AND/OR (2) Socket Wrenches and Sockets #27 #42 #9 #8 #11 #31 #22 #24 #41 (1) This is what your system will look like whe ...

  • Huffy 21168202 - page 17

    10/04 P/N 211682 02 17 48 31 11 9 25 49 Assemble backboard support brackets (25) using bolt s (9 & 48), spacers (31), and nut s (1 1 & 49) as shown. 2. 28 24 22 27 28 25 29 22 Attach lower elevator tubes (28) and counter balance spring (29) to backboard support bracket s (25) using spacers (22), bolt (27), and nut (24) as shown. 1. ...

  • Huffy 21168202 - page 18

    18 P/N 211682 02 10/04 3. 25 53 53 53 52 53 4. Attach upper elevator tubes (30) to backboard support bracket s (25) using spacers (22), bolt (27), and nut (24) as shown. 42 41 42 41 47 24 27 22 22 30 30 25 52 Place board spacers (52) into board as shown. Bend upper portion of the board brackets (25) to match holes in backboard as shown. Insert t-bo ...

  • Huffy 21168202 - page 19

    10/04 P/N 211682 02 19 SECTION C: A TT ACH THE BACKBOARD & ELEV A T OR ASSEMBL Y T O POLE SYSTEM 3/4” #27 #46 #24 #45 #23 #39 #44 #43 #33 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) Phillips-Head Screwdriver (2) 3/4" Wrenches AND/OR (2) Socket Wrenches and Sockets Container to Mix This is what your sy ...

  • Huffy 21168202 - page 20

    20 P/N 211682 02 10/04 1. 1 24 30 30 23 23 23 23 24 28 28 2. Support pole on sawhorse. Attach backboard assembly to top pole section (1). Install handle assembly to long elevator tubes (28) using bolt (27), spacers (39), and nut (24) as shown. 27 27 USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW T ...

  • Huffy 21168202 - page 21

    10/04 P/N 211682 02 21 3. 43 46 45 41 42 Inst all Slam Jam Rim to Backboard 32 44 42 45 46 A B C D E A • Fit rim (32) securely into bracket (41) as shown (Allow "T"-bolt (42) to slip through center hole in rim (32). B • Install reinforcement bracket (43) onto “T” bolt (42) as shown. C • Install spring (44) onto “T” bolt (42) ...

  • Huffy 21168202 - page 22

    22 P/N 211682 02 10/04 4. 24 27 30 30 Insert bolt (27) through left side of short elevator tube (30), then stretch spring or springs (29) onto bolt (27). Insert bolt (27) through right side of short elevator tube (30) and secure with nut (24). USE EYE PROTECTION WHEN INST ALLING SPRINGS. W ARNING! 29 Place rebar with spacers into bottom pole sectio ...

  • Huffy 21168202 - page 23

    10/04 P/N 211682 02 23 Fill pole with concrete approximately 1” (2.54 cm) below bottom elevator hole as shown. IMPORT ANT!: W AIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEP . CONCRETE MUST CURE. 1 8. IMPORT ANT!: F AILURE TO FILL YOUR POLE COMPLETEL Y WITH CONCRETE AS DESCRIBED IN THESE INSTRUCTIONS WILL VOID ALL W ARRANTIES WRITTEN AND I ...

  • Huffy 21168202 - page 24

    24 P/N 211682 02 10/04 9. Install clip s. Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows. Push second “arm” back and into ram as shown. T wist “body” of clip slightly again to spread “arms ...

  • Huffy 21168202 - page 25

    10/04 P/N 211682 02 25 T wist net until it snaps into position. Net must be centered through clip. NET INST ALLA TION 10. 32 33 34 Insert net into bottom of clip as shown. SIDE VIEW NET NET NET CLIP NET CLIP ...

  • Huffy 21168202 - page 26

    26 P/N 211682 02 10/04 SECTION D: UPRIGHT , SECURE AND USE POLE SYSTEM Wedge Hammer None This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) ...

  • Huffy 21168202 - page 27

    10/04 P/N 211682 02 27 5 2. 1. Af ter concrete has cured, remove t ape, install pole cap (26), fit pole assembly into sleeve (4). Use wedge to gently tap cap of ground sleeve (5) until tight. 4 PLA YING SURF ACE 26 USE CAUTION; ASSEMBLY IS HEAVY. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY A ...

  • Huffy 21168202 - page 28

    28 P/N 211682 02 10/04 4. 16 B. A. C. 3. A. While holding handle, remove pin (16). B. Move elevator up or down to desired height. C. Replace pin (16) full length to lock system at desired height. Apply height adjustment label (35) to front of pole as shown. Regulation rim height is 10 feet (3.05 m). 10 f t. (3.05 m) 2 2 1 3 201251 2/99 HEIGHT ADJUS ...

Fabricante Huffy Categoría Board Games

Los documentos del dispositivo Huffy 21168202 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Huffy
- manuales de instrucciones 21168202
- hojas de producto Huffy
- folletos informativos
- o etiquetas energéticas Huffy 21168202
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Huffy 21168202.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Huffy 21168202, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Huffy 21168202. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Huffy 21168202.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Huffy 21168202, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Huffy 21168202. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Huffy 21168202.

El manual de instrucciones completo de Huffy debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Huffy 21168202 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Huffy 21168202, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Huffy 21168202 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Huffy 21168202 - que deben facilitarnos los primeros pasos durante el uso de Huffy 21168202
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Huffy 21168202
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Huffy 21168202 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Huffy 21168202?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Huffy 21168202, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Huffy 21168202 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)