Español dropdown-ico

Manual de instrucciones Craftsman 486.2484

24 de páginas 1.15 mb
Descargar

Pasar a la página of 24

Summary
  • Craftsman 486.2484 - page 1

    Owner's Manual CRI1FTSMI1N 40"- 2 STAGE SNOW THROWER TRACTOR ATTACHMENT Model No. 486.248400 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. • Safety • Assembly • Operation • Maintenance • Parts : Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. PRINTED IN U.S. ...

  • Craftsman 486.2484 - page 2

    ACCESSORIES ................................ , .......................... 2 SAFETY RULES.._.._ ........ L..i_L_._._: .......................... 3 FULL SIZE HARDWARE CHART ......... : ....................... 4 CARTON CONTENT*S..._..,_ ...... . .:.: ...... : ....................... 5 ASSEMBLY .......................................................... ...

  • Craftsman 486.2484 - page 3

    Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment, • Read this owner's manual carefully and know how to operate your snow thrower and how to stop the unit and disengage the controls quickly. • Never allow (_h ...

  • Craftsman 486.2484 - page 4

    SHOWN ACTUAL SIZE Two shear bolts (X) and hex lock nuts (Y) are provided as replacement parts for the spiral augers. Store in a safe place until needed. (See page 17,) U IW I I NOT SHOWN ACTUAL SIZE /Z cc /GG REF. A B C - D E F G H I J K L M N O P QTY. 1 4 2 6 2 4 2 2 6 4 12 10 1 6 2 2 DESCRIPTION Hex Bolt, 1/2" x 1-1/4" Hex Bolt, 3/8&quo ...

  • Craftsman 486.2484 - page 5

    CARTON CONTENTS 1. Cross Brace (Weight Tray) 2. Side Brace (Weight Tray) 3. Right Hand Side Plate (Stamped "R';) 4. Left Hand Side Plate (Stamped "L") 5. Anti-rotation Bracket 6. Engagement.Rod 7. Engine Pulley Keeper 8. Chute Crank Rod Assembly 9. Support Tube, Crank Rod 10. Plastic Keg 11. Left Hand Hanger Bracket (Stamped &qu ...

  • Craftsman 486.2484 - page 6

    TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches (2) 1/2" Wrenches (2) 9/16" Wrenches (2) 3/4" Wrenches (1) Knife ADDITIONAL ITEMS REQUIRED General Purpose Grease ASSEMBLY OF PARTS TO TRACTOR FRAME Right hand (R.H.) and left hand (L.H.) are determined fTOm the operators position while seated on the tractor. • Remove and save two ...

  • Craftsman 486.2484 - page 7

    • Assemble a shoulder bolt to the bottom hole in each side plate, securing each bolt with a 3/8" lock washer and a 3/8" hex lock nut. See figure 3. _8" HEX LOCK NUT 3/8"LOCK WASHER R. H. SIDE PLATE 3/8"SHOULDER BOLT FIGURE3 INSTRUCTIONS FOR TRACTORS WITH FOOT REST BRACKETS UNDER THE FOOT RESTS (Figure 4.) • Remove and d ...

  • Craftsman 486.2484 - page 8

    • Assemble a shoulder bolt arid 3/8" hex lock nut to the R.H. side of the tractor fi'ame, using the first empty hole to the rear of the R.H. hanger bracket. See figure 7 Replace the engine puney keeper on your tractor with the new pulley keeper supplied with the snow blower. Attach the keeper to the frame using the original bolt, washer ...

  • Craftsman 486.2484 - page 9

    Make sure the attachment clutch lever on the dash panel is in the disengaged (down) position. Position the idler arm so that it points straight forward, as shown in figure 10. Align the engage- ment rod trunnion with the hole in the idler arm by screwing the trunnion in or out on the rod. Attach the trunnion to the idler arm using a 5/64" hair ...

  • Craftsman 486.2484 - page 10

    Attach the snow thrower's clutch/idler assembly to the tractor frame by sliding the notched arms at the rear of the assembly onto the two shoulder bolts assembled to the inside of the tractor frame. Lift the front of the assembly so that the sides fit inside the R.H. and L.H. hanger brackets. Attach the assembly to the brackets using two pivot ...

  • Craftsman 486.2484 - page 11

    Insert the end of the lift release cable into the hole in the lift rod. Place the cable into the slot in the top of the lift bracket, with one hex nut above the slot and one hex nut and lock washer below the slot. Tighten the nuts, adjusting them to take out excess stack in the cable wire just above the nuts. See figure 17. / CABLE WIRE __ _Jj.HEXN ...

  • Craftsman 486.2484 - page 12

    Coat the top of the ring around the discharge opening with general purpose grease. See figure 21. Place the discharge chute (facing forward) onto the ring. Place the anti-rotation bracket on top of the chute flange, aligning it with the holes on the right hand side of the flange. Attach the three chute keepers (right side up as shown) to the bottom ...

  • Craftsman 486.2484 - page 13

    Beneath the tractor, the idler eirm on the bottom of the clutch/idler assembly should be pivoted to the left side of the tractor as shown in figure 23. Place the auger belt around the rear pulley and between the two idler pulleys with the "V" side of the belt seated in the grooves of the "V" pulleys. See figure 23. IDLER ARM LEF ...

  • Craftsman 486.2484 - page 14

    • Fill the plastic keg full of dry sand (approximately CHECKLIS'I _ 75 Ibs.) and replace the lid. Place the plastic keg on the weight tray. Secure the keg with the rubber tarp strap hooked into the holes in the cross brace. See figure 26. TARP STRAP FIGURE 26 Before you operate your snow thrower, please review the following checklist to help ...

  • Craftsman 486.2484 - page 15

    KNOW YOUR SNOW THROWER Read this owner's manual and safety rules before operating your snow thrower. Compare the illustration below with your snow thrower to familiarize yourself with the various controls and their locations. LIFT HANDLE CHUTE TILT HANDLE UPPER CHUTE LOWER CHUTE .... CRANK ROD J SCRAPER PLATE SPIRALAUGERS, R.H.&L.H, SKIDSH ...

  • Craftsman 486.2484 - page 16

    RAISING_AND LOWERING • To raise, push down on the lift handle until the snow thrower locks in the raised transport position. • To lower, push down slightly on the lift handle and pull the trigger. With the trigger pulled, slowly lower the snow thrower until it reaches the ground. A CAUTION: Do not operate the snow thrower without the rear weigh ...

  • Craftsman 486.2484 - page 17

    & CAUTION: Before servicing or adjusting the snow thrower, shut off the engine, remove the spark plug wire(s), set the parking brake and remove the key from the tractor ignition. REPLACING AUGER DRIVE BELT • Lower the snow thrower to the ground. • Remove the attachment pin. See figure 22. • Lock the snow thrower's lift handle in the ...

  • Craftsman 486.2484 - page 18

    STORAGE RECOMMENDATIONS • Lower the snow thrower to the ground. • Remove the snow thrower from the tractor. • Clean the snow thrower thoroughly. Wash off any salt deposit-which may have dried on the thrower and housing. • Any bare metal that has become exposed should be painted or coated with a light oil to prevent rust. • Store in a dry ...

  • Craftsman 486.2484 - page 19

    SLOPE GUIDE (Keep this sheet in a safe place for future reference.) Use this guide to determine if a slope is safe for the operation of your tractor and snow thrower, Refer also to the instructions in your vehicle owners manual. -T . IIIIIHIIIIIIIHHiillmlllitllDlilHIl|ilillilillilUl|llll .1 19 ...

  • Craftsman 486.2484 - page 20

    REPAIR PARTS FORMODEL 486.248400 40" SNOWTHROWER 16 33 / 8 3O 27.. 26 28 19 34 11 21 / 34 31 37 21 9 27 27 63 91 98 92 47 65 82 43 82 65(.) 25 21 35 30 • J 96 97 4954_ 95 "71 68 91 20 ...

  • Craftsman 486.2484 - page 21

    i REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ! 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 _41 42 43 44 45 46 47 48 49 50 REPAIR PARTS FOR MODEL 486.248400 40" SNOW THROWER PART NO. 05931 63562 618-0161A 63579 63768 24278 703-2734 703-2735A 703-2736 705-5226 705-5269 705-5270 43182 44950 44917 44326 43080 46703 ...

  • Craftsman 486.2484 - page 22

    REPAIR PARTS FOR MODEL 486.248400 40" SNOW THROWER 42 43 41 40 45 _% 4O 63 / 69 47 51 50 53 18 52 56 / 6O 57 18 65 39 15 14 13 54 16 6 6 78 _---3 55 12 23 6 61 28 24 11 18 22 63 38 76 "" A 22 ...

  • Craftsman 486.2484 - page 23

    REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2O 21 22 23 24 25 28 27 28 29 3O 31 32 33 34 35 36 37 38 39 4O REPAIR PARTS FOR MODEL 486.248400 40" SNOW THROWER PART NO. 63764 710-0865 710-0964,a 711-0332 712-0386, a 43262 43010 142 43093 | R19171616 736-0366 741-0192 783-0380 783-0381 24476 24311 43063 43086 24298 683-0130 747-3248A ...

  • Craftsman 486.2484 - page 24

    For in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME (1-800-469-4663) Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811 In Canada for all your service and parts needs call - 1-800-665-4455 Au Canada pour tout le service ou les pi_ces For the repair or replacement parts you need: Call 7 am - 7 pm, 7 ...

Fabricante Craftsman Categoría Snow Blower

Los documentos del dispositivo Craftsman 486.2484 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Craftsman
- manuales de instrucciones 486.2484
- hojas de producto Craftsman
- folletos informativos
- o etiquetas energéticas Craftsman 486.2484
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Craftsman 486.2484.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Craftsman 486.2484, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Craftsman 486.2484. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Craftsman 486.2484.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Craftsman 486.2484, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Craftsman 486.2484. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Craftsman 486.2484.

El manual de instrucciones completo de Craftsman debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Craftsman 486.2484 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Craftsman 486.2484, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Craftsman 486.2484 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Craftsman 486.2484 - que deben facilitarnos los primeros pasos durante el uso de Craftsman 486.2484
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Craftsman 486.2484
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Craftsman 486.2484 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Craftsman 486.2484?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Craftsman 486.2484, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Craftsman 486.2484 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)