-
TANDBERG MSE 8350 - page 1
Codian IP Gateway MSE 8350 Getting started ...
-
TANDBERG MSE 8350 - page 2
Codian IP Gateway MSE 8350 Getting started ...
-
TANDBERG MSE 8350 - page 3
Copy right © T ANDBERG 2008. All rights reser v ed. This Getting Star ted Guide ma y not be copied, photo copied, translated, repr oduced, or con verted into any electronic or machine-readable form in whole or in par t without prior wr itten appro v al of T ANDBERG . T ANDBERG reser ves the right to re vise this documenta tion and to make changes ...
-
TANDBERG MSE 8350 - page 4
T able of con tents General inf ormation .......... .......... .......... ........... .......... .......... ........... .......... ............. .......... .. .... . 1 About the M SE 8350 IP G W blade .......... ............ ........... ............ ........... .......... ....... 1 Port and L ED location .............. ........... .......... ...... ...
-
TANDBERG MSE 8350 - page 5
General information 1 General informa tion About the MSE 8350 IP GW blade The MSE 8350 IP GW blade fits into an MSE 8000 chassis . The IP GW blade is a voice and video ga tew a y that allo ws calls to be made betw een pairs of IP endpoints that cannot nor mall y connect directl y to each other . A second Ethern et por t allows for connections betw ...
-
TANDBERG MSE 8350 - page 6
2 LED behavior T able 1 descr ibes the behavior of the LEDs . T able 1: IP GW blade LED behavior LED Co lor Indicates Compact Flash Activity Flashing gr e en One of: the IP GW bl ade is booting a configuration change has been made the configuration is being transferred by F T P Console Link Green A PC is connected to the console port St ...
-
TANDBERG MSE 8350 - page 7
General information 3 Ethernet P or t Status , for each Ether net por t: FDX Green The link has been negotiated as a full- duplex link Act Green Pa c kets ar e being transmitted on this por t Link Green The speed of the link from this port, which is either 10, 100, or 1000 Mbps P o wer Blue The IP GW blade is receiving po w er from the MSE 8000 cha ...
-
TANDBERG MSE 8350 - page 8
4 Installing the IP GW blade F or infor mation about po wering the MSE 8 000, refer to the Getting Star ted Guide that accompanied the chassis. Step one: Install the IP GW blade into the MSE 8000 chassis 1 Remov e th e blade or b lanking blade from the slot into which you are going to install the IP GW blade: i Using a No .1 Phillips screwdriv er , ...
-
TANDBERG MSE 8350 - page 9
Installing the IP GW blade 5 5 Using a No .1 Phillips screwdriver , tighten the screws in the retaining la tc hes with a clockwise quar ter tur n. Figur e 2: Inser ting a blade into the chassis Figur e 3: Closing the retaining latches on the front of a blade ...
-
TANDBERG MSE 8350 - page 10
6 Step two: C onnec t to Ethernet P ort s A and B Connect an Ethernet cable from Ethernet P or t A to an Ether net switch (rather than a hub , to minimize interference from ot her de vices on the netw ork). The Ether net por t is a 10/100/1000 Mbps auto-sensing connection. Connect P or t A to your local netw ork and connect P o r t B to a second su ...
-
TANDBERG MSE 8350 - page 11
Initial configuration 7 Initial configur ation Step one: Configur e Et hernet P orts A and B The default setting for the IP GW blade Et her net por ts is auto-sensing mode. If the switch por ts to whic h you connect the IP GW blade ar e not also set to auto-sensing mode, then y ou need to configure the IP GW b lade Ether net por ts to use the same ...
-
TANDBERG MSE 8350 - page 12
8 Co nfiguring the IP GW blade Step one: Log in to the IP GW blade All administration of the IP GW b lade is performed through the w e b interface . T o log in to the web interface of the IP GW b lade: 1 Log in to the Super visor’ s w eb interface . 2G o t o Hardware > Blades and clic k the IP address of the IP GW blade. 3C l i c k Click here ...
-
TANDBERG MSE 8350 - page 13
Configuring the IP GW blade 9 Step three: C onfigure the au to attendant menus (optional) Depending on the proposed configura tion of yo ur dial plan, and the settings for failed calls, callers can be connected to an auto attendant menu. The IP GW b lade provi des a highly flexib le menu-creation featur e. This enables y ou to create a menu (or a m ...
-
TANDBERG MSE 8350 - page 14
10 Step five: A dd endpoints and call groups (optional) Y ou can pre-configure a list of endpoints on the IP GW b lade. F or these endpoints, an operator or caller can simpl y choose the endpoint's name from an onscreen address book, rather than ha ving to type in the endpoint's address when a caller wants to be connected to that endpoint ...
-
TANDBERG MSE 8350 - page 15
Checking for updates 11 Checking for updates It is a good idea to regularl y chec k for updates to the main IP GW blade softw are image. This section describes ho w to upgrade the IP GW blade using the w eb interface. No te that y ou can also upgrade the IP GW blade using FTP; this can be more reliab le if you ar e upgrading the device r emotel y . ...
-
TANDBERG MSE 8350 - page 16
12 T roubleshooting and technical suppor t information Using the ev ent log to help solve a problem Unless you are ex periencing a prob lem, all e v ent logging sources should be set to the default, which is Errors, warnings and information . F or more infor mation about configur ing the ev ent log , refer to the online help accessible fr om the w ...
-
TANDBERG MSE 8350 - page 17
61-0018-04 ...
¿Tienes una pregunta acerca de TANDBERG MSE 8350?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con TANDBERG MSE 8350, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con TANDBERG MSE 8350 probablemente compartirá una forma de solucionarlo.