Español dropdown-ico

Manual de instrucciones Troy-Bilt 630C

32 de páginas 3.74 mb
Descargar

Pasar a la página of 32

Summary
  • Troy-Bilt 630C - page 1

    O mm 'W//////aI&_AIIIIIIIIIIIIIF / m mllllllllllllllllml m Operator's Manual ® Rear-tine Tiller Models 630C--Tuffy 634AmSuper Bronco TM Mode1634A Shown IMPORTANT: Read safety rules and instructions carefully before operating equipment. Warning: This unit is equipped with an internal combustion engine and should not be used on or near ...

  • Troy-Bilt 630C - page 2

    TABLE OF CONTENTS Content Page Content Page Customer Support 2 Maintenance 17 Safety 3 Off-season Storage 21 Assembly 6 Troubleshooting 22 Features and Controls 10 Parts List 23 Operation 12 Warranty Back Cover FINDING MODEL NUMBER This Operator's Manual is an important part of your new lawn tractor. It will help you assemble, prepare and main ...

  • Troy-Bilt 630C - page 3

    SECTION 1: SAFETY This machine meets voluntary safety stan- dard B71.8-1996, which is sponsored by the Outdoor Power Equipment Institute, Inc., and is published by the American National Standards Institute. WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reprod ...

  • Troy-Bilt 630C - page 4

    4.Exercise caution toavoid slipping or fall- ing. 5.If the unit should start to vibrate abnor- mally, stop the engine, disconnect the spark plug wire and prevent it from touch- ing the spark plug, and check immediately for the cause. Vibration is generally a warning oftrouble. 6. Stop the engine, disconnect the spark plug wire and prevent it from t ...

  • Troy-Bilt 630C - page 5

    Decals For your safety and the safety of others, vari- ous safety and operational decals are located on your unit (see Figure 1-2). Keepthe decals clean and legible at all times. Contactyour local service dealer or the factory for replacementsif any decals are damaged or missing. Referto the Parts List pages in this Manual for decal locations, desc ...

  • Troy-Bilt 630C - page 6

    SECTION 2: ASSEMBLY WARNING: To prevent personal injury or property damage,do not start the engine until all assembly steps are complete and you have read and understand the safety and operating instructions in this manual. INTRODUCTION Carefully follow these assembly steps to correctly prepare your tiller for use. It is recommended that you readth ...

  • Troy-Bilt 630C - page 7

    A J B °-! ° Fig. 2-3: Wheel in FREEWHEEL position STEP 4: INSTALL FORWARD CLUTCH CABLE 1. Carefully unwrap the forward clutch ca- ble (cable without an attached knob) from its shipping position and slide the thin ca- ble wire (T, Fig. 2-4) into the slot in the ca- ble bracket. Push the cable connector (U, Fig. 2-4) up through the hole in the brac ...

  • Troy-Bilt 630C - page 8

    4. Check for correct tension on the forward drive belt by taking two measurements of the cable spring, as follows: a. With the Forward Clutch Bail (Y, Fig. 2- 6) in an open (released) position, measure the length of the cable spring (W) from the outermost coil to the outermost coil. b. Squeeze the Forward Clutch Bail against the handlebar (see Fig. ...

  • Troy-Bilt 630C - page 9

    5! 6: CHECK TRAHSMiSSiOH OIL LEVEL The transmission was filled with gear oil at the factory. However, you should check the gear oil level at this time to make certain it is correct. IMPORTANT: Do not operate the tiller if the gear oil level is low. Doing so will result in severe damage to the transmission com- ponents. 1. With the tiller on level g ...

  • Troy-Bilt 630C - page 10

    SECTION 3: FEATURES AND CONTROLS _ ARNING: Before operating your machine, carefully readand understand all safety, controls and operating instructions in this Manual, the separateEngine Owner's Manual,and on the decals on the machine. Failure to follow these instructions can result in serious personal injury. INTRODUCTION This Section describe ...

  • Troy-Bilt 630C - page 11

    _ WARNING: Use extreme _-- _ caution when reversing or A Y pulling the machine towards ,,_- D you. Look behind to avoid obstacles. Never attempt to till in reverse. Failure to follow this warning could result in personal injury or property damage. To operate the ReverseClutchControl: 1. Put wheels in WHEELDRIVE position (see "WARNING" sta ...

  • Troy-Bilt 630C - page 12

    SECTION 4: OPERATION _ ARNING: Before operating your machine, carefully readand understand all safety (Section 1), controls (Section 3) and operating instructions (Section 4) in this Manual, the separateEngine Owner's Manual,and on the decals on the machine. Failure to follow these instructions can result in serious personal injury. INTRODUCTI ...

  • Troy-Bilt 630C - page 13

    Stopping the Engine and Tiller 1. To stop the wheels and tines, release the Forward Clutch Bail (all models) orthe Re- verse Clutch Control (Model 634A) -- whichever control is in use. 2. To stop the engine, put the ignition switch and/or the throttle control lever in the "OFF" or "STOP" position. OPERATING THE TILLER The follow ...

  • Troy-Bilt 630C - page 14

    TILLING TIPS & TECHNIQUES Tilling Depths WAHNINL_: Before tilling, contact your telephone or utilities company and inquire if underground equipment or lines are used on your property. Do not till near buried electric cables, telephone lines, pipes or hoses. • Avoid pushing down on the handlebars in an attempt to force the tiller to dig deeper ...

  • Troy-Bilt 630C - page 15

    TILLING TIPS & TECHNIQUES (CON'T) Power Composting Power composting simply meanstilling under and burying in the soil all manner of organic matter suchas crop residues, leaves, grassclippings and covercrops. This material will de- compose during the non-growing season and add important natural nutrients to the soil. The first place to begi ...

  • Troy-Bilt 630C - page 16

    TILLING TIPS & TECHNIQUES (CON'T) Terrace Gardening (continued) • To createa terrace, start at the top of the slope and work down. Go backandforth across the first row as shown in Fig. 4-10. • Each succeeding lower terrace is started by walking below the terraceyou're pre- paring. For addedstability of the tiller, always keep the ...

  • Troy-Bilt 630C - page 17

    SECTION 5: MAINTENANCE WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructions can result in serious personal injury or proper ...

  • Troy-Bilt 630C - page 18

    WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. 4. The gear oil level is correct if the gear oil is approx ...

  • Troy-Bilt 630C - page 19

    ,_ WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. FRONT/ FORWARD C Figure 5-3: Instafl tines so that cu ...

  • Troy-Bilt 630C - page 20

    ,_ WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. FORWARD CLUTCH BAIL ADJUSTMENT If the Forward Clutch Ba ...

  • Troy-Bilt 630C - page 21

    ,_ WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. 3. Clean around the oil dipstick or oil fill tube (whic ...

  • Troy-Bilt 630C - page 22

    PROBLEM Engine does not start Engine runs poorly. Engine overheats. Engine does not shot off Wheels andTines will not turn Tines turn,but wheels don't, Wheels Turn, but Tines Don't, Poor tillingperformance. WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, ...

  • Troy-Bilt 630C - page 23

    SECTION 6: MODELS 630C & 634A PARTS LIST 1 13 3 2O 4 15_ REF PART NO. NO. 1 1185469 715-0108 2 710-0597 3 710-0599 4 710-0874 5 710-3008" 6 712-0324 712-04064 7 712-0429t 712-04063 8 1916707 9 736-0119 10 GW-55013-1 11 GW-55013-2 12 GW-55015 *4 on Mode1634A t 6 on Mode1634A 12 7_ DESCRIPTION Spirol Pin (B) Spirol Pin (A) Hex Hd. Screw, 1/4 ...

  • Troy-Bilt 630C - page 24

    MODELS 630C & 634A 5 15 2O 17 22 I 16 12 18 6 14 18 23 24 ...

  • Troy-Bilt 630C - page 25

    MODELS 630C & 634A REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 20 21 22 23 25 PART NO. DESCRIPTION 1916719 1916755 747-04210 1918745 710-0599 710-3008 712-3009 786-04188 GW-55043 786-04200 GW-55044 GW-9855 725-0157 736-3050 786-04040 732-04185 710-0106 710-0216 710-0805 712-0121 712-0291 712-3000 736-0119 Cable Assembly, Reverse Clutch ...

  • Troy-Bilt 630C - page 26

    MODELS 630C & 634A (A) For Model 6300 (B) For Model 634A REF NO. 1 2 3 4 5 6 * Use as PART NO. DESCRIPTION GW-9517 GW-9400 GW-50043 711-04109 711-04110 GW-9401 GW-1224-1" GW-1224-2" GW-1224-3" GW-1224-4" GW-1325C Snap Ring Drive Shaft Bearing Cup Support Washer, Rear Drive Shaft (B) Drive Shaft (A) Drive Shaft Bearing Cone S ...

  • Troy-Bilt 630C - page 27

    MODELS 630C & 634A FRONT 11 7 4 3 4 1 2 .,J (A) For Model 6300 (B) For Model 634A REF NO. 1 2 3 4 5 6 7 8 9 10 11 * Use as PART NO. DESCRIPTION GW-9512 1909950 GW-1166-1 * GW-1166-2" GW-1166-3" GW-1166-4" GW-1166-5" GW-1086 711-04092 711-04088 GW-9305 GW-1132-2 1904278 711-04078 GW-1104 1904279 1916542 Retainer, Snap Ring, & ...

  • Troy-Bilt 630C - page 28

    MODELS 630C & 634A 2 I 2 11" 10 10 12 13 * included with transmission when purchased as an assembly only. Remove and discard when installing the transmission on tiller. REF NO. 1 2 3 4 5 6 7 PART NO. GW-9727 710-04049 736-0119 1918377 1916641 GW-50032 721-04030 DESCRIPTION REF NO. Plug, Transmission Oil Fill 8 Hex Hd. Flange Screw, 5/16-18 ...

  • Troy-Bilt 630C - page 29

    MODELS 630C & 634A RIGHT-HAND TINE Hold Tines With Blunt End Toward You LEFT-HAND TINE NOTE: Identify Left and Right sides of tiller by standing in operator position and facing direction of forward travel, 1 10 FRONT WHEEL SHAFT ,.11 (A) 3 (B) TINE SHAFT 3 (A) For Model 630C (B) For Model 634A REF PART NO. NO. 1 710-0514 2 GW-50049-02 3 712-300 ...

  • Troy-Bilt 630C - page 30

    MODELS 630C & 634A 24 3O ...

  • Troy-Bilt 630C - page 31

    MODELS 630C & 634A (A) For Model 630C (B) For Model 634A REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2O 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 PART NO. DESCRIPTION 736-0159 714-0139 1916531 1916532 656-04023 1916535 1916652 1916657 1916658 1916660 1916724 1916725 1916726 1916794 1916795 1917326 19 ...

  • Troy-Bilt 630C - page 32

    TROY-BILT TILLER LIFETIME LIMITED WARRANTY WHAT PRODUCT IS COVERED All Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions. This warranty begins on the date of purchase and is warranted by Troy-Bilt LLC for the life of the tiller, to the original purchaser only. WHAT IS COVERED Troy-Bilt LLC will, at its option, repair or ...

Fabricante Troy-Bilt Categoría Tiller

Los documentos del dispositivo Troy-Bilt 630C que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Troy-Bilt
- manuales de instrucciones 630C
- hojas de producto Troy-Bilt
- folletos informativos
- o etiquetas energéticas Troy-Bilt 630C
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Troy-Bilt 630C.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Troy-Bilt 630C, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Troy-Bilt 630C. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Troy-Bilt 630C.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Troy-Bilt 630C, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Troy-Bilt 630C. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Troy-Bilt 630C.

El manual de instrucciones completo de Troy-Bilt debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Troy-Bilt 630C - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Troy-Bilt 630C, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Troy-Bilt 630C que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Troy-Bilt 630C - que deben facilitarnos los primeros pasos durante el uso de Troy-Bilt 630C
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Troy-Bilt 630C
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Troy-Bilt 630C en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Troy-Bilt 630C?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Troy-Bilt 630C, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Troy-Bilt 630C probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)