-
Makita 6070DW - page 1
Cordless Driver Drill No load speed Variable Speed, Reversible MODEL 6070D MODEL 6070DW With 3 Hour Charger weight I Net Dimensions (L x W x H) INSTRUCTION MANUAL SPECIFICATIONS - Model 6070D With Reversinq Switch & Battery 10 mm 4.5 mm x 20 mm 211 mmx49mmx192mm 1.0kg (318") I (3116 x 314") I - 6oo I (8-114" x 1-718" x 7-112 ...
-
Makita 6070DW - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invite in ...
-
Makita 6070DW - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only exten- ...
-
Makita 6070DW - page 4
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS -This manual con- tains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA ...
-
Makita 6070DW - page 5
ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1. The Charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this Charger. Do not attempt to charge the tool with any other charger. 2. Do not charge the tool when temperature is BELOW 10°C (50°F) or ABOVE 45°C (113°F). 3. Do not use ch ...
-
Makita 6070DW - page 6
Charging Uncap the charging connector hole. Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. CAUTION: 0 The battery in your new tool is not fully charged. You will need to charge it before use. 0 Do not operate the tool during charging. 0 Overcharging more than 2 days con ...
-
Makita 6070DW - page 7
Installing or removing driver bit CAUTION : When installing or removing the bit, be careful not to touch the trigger switch. To install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise. Be sure to tighten all three chuck holes evenly. To remove the b ...
-
Makita 6070DW - page 8
Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the reversing switch to the right for clockwise rotation or to the left for counterclockwise. Reversing switch - CAUTION: 0 Always check the direction of rotation before operation. 0 Use the reversing switch only when the tool comes to a complete sto ...
-
Makita 6070DW - page 9
Bubble level This tool is equipped with a bubble level to aid in holding the tool horizontally. Simply center the bubble in the sight window. Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed grad- ually. Release the trigger just as the screw ...
-
Makita 6070DW - page 10
Storage of driver bit When not using the driver bit, return it to the storage cavity on the bottom of the tool. Drilling operation 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. 0 Drilling in metal To preve ...
-
Makita 6070DW - page 11
CAUTION: 0 Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. 0 There is a tremendous force exerted on the toolibit at the time of hole breakthrough. Hold the tool firmly and exert car ...
-
Makita 6070DW - page 12
MAINTENANCE CAUTION: Always be sure that the tool is switched off before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replace- ment parts. 12 ...
-
Makita 6070DW - page 13
ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner Phillips bit 0 Bits I I 0 Rubber pad assembly 8 - a ...
-
Makita 6070DW - page 14
14 A 10 mm (3/8) CORDLESS DRIVER DRILL Model 6070D Note The switch and other part configuratlons may differ from country to country ...
-
Makita 6070DW - page 15
MOL ITEM NO. - 1 2 3 4 5 6 7 8 9 10 11 Note 1 370D , DESCRIPTION ",'," & DESCRIPTION NE -E Drill Chuck S10 Pan Head Screw M5xl8 Gear Molor Holder 6 Switch Housing R Bubble Level Tapping Screw 3x20 Cap Plane BearlnQ 5 12 13 14 15 16 17 18 19 20 21 1 Intel 1 Resistance 1 Diode 1 1 Plane Bearing 3 1 Switch 1 Housing L 1 Name Plate 1 ...
-
Makita 6070DW - page 16
10 mm (3/8”) MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLE ...
¿Tienes una pregunta acerca de Makita 6070DW?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 6070DW, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 6070DW probablemente compartirá una forma de solucionarlo.