-
Ryobi HD500 - page 1
OWNER'S OPERA TING MANUAL 1/2 in. (13 mm) Hammer Drill - HD500 DOUBLE INSULA TED SA VE THIS MANUAL FOR FUTURE REFERENCE THANK YOU FOR BUYING A RYOBI HAMMER DRILL. Your new hammer drill has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give y ...
-
Ryobi HD500 - page 2
Page 2 TABLE OF CONTENTS 1. Product Specifications ................................................................................... 1 2. T able Of Contents .......................................................................................... 2 3. Rules For Safe Operation ...................................................................... ...
-
Ryobi HD500 - page 3
Page 3 READ ALL INSTRUCTIONS 1. KNOW YOUR POWER TOOL. Read owner's manual carefully. Learn its applications and limitations as well as the specific potential hazards related to this tool. 2. GUARD AGAINST ELECTRICAL SHOCK by preventing body contact with grounded surfaces. For example: Pipes, radiators, ranges, refrigerator enclosures. 3. KEEP ...
-
Ryobi HD500 - page 4
Page 4 RULES FOR SAFE OPERA TION (Continued) authorized service center unless indicated elsewhere in this instruction manual. 31. DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center. 32. DRILLING INTO ELECTRICAL WIRING IN WALLS CAN CAUSE DRILL BIT AND CHUCK TO BECOME ELECTRICALLY L ...
-
Ryobi HD500 - page 5
Page 5 APPLICATIONS (Use only for the purposes listed below) 1. Hammer drilling in concrete and masonry. 2. Drilling in wood. 3. Drilling in ceramics, plastics, fiberglass, and laminates. 4. Drilling in both hard and soft metals. 5. Using driving accessories, such as driving screws with screwdriver bits. 6. Mixing paints. ELECTRICAL CONNECTION Your ...
-
Ryobi HD500 - page 6
Page 6 SWITCH See Figure 2. To turn your hammer drill ON , depress the switch trigger. Release switch trigger to turn your hammer drill OFF . LOCK-ON BUTTON See Figure 2. Your hammer drill is equipped with a "lock-on" feature, which is convenient when continuous drilling for extended periods of time is required. To lock-on, depress the sw ...
-
Ryobi HD500 - page 7
Page 7 VARIABLE SPEED See Figure 5. Your hammer drill has a variable speed control selector designed to allow operator control and adjustment of speed and torque limits. Speed and torque can be increased or decreased by rotating the variable speed control selector in the direction of the arrows shown in figure 5. NOTE: Hold your hammer drill in nor ...
-
Ryobi HD500 - page 8
Page 8 OPERA TION INSTALLING AUXILIARY HANDLE (Continued) 4. Align tabs on depth gage clamp with slots in threaded hole in motor housing. NOTE: Depth gage clamp can be rotated 180 ° so that depth gage rod will fit on either side of motor housing. 5. Carefully start the fine screw threads (#3/8-24) into fine threaded hole in motor housing and tight ...
-
Ryobi HD500 - page 9
Page 9 RIGHT OPERA TION W ARNING: Your hammer drill should never be connected to power supply when you are assembling parts, making adjustments, installing or removing drill bits, or when not in use. Disconnecting your drill will prevent accidental starting that could cause serious injury. TO INSTALL BITS See Figure 9. 1. UNPLUG YOUR HAMMER DRILL. ...
-
Ryobi HD500 - page 10
Page 10 W ARNING: Always wear safety goggles or safety glasses with side shields when operating hammer drill. Failure to do so could result in dust, shavings, or loose particles being thrown into your eyes, resulting in possible serious injury. DRILLING See Figure 11. 1. Depress and release the switch trigger to be sure your drill is in OFF positio ...
-
Ryobi HD500 - page 11
Page 11 CHUCK REMOVAL CHUCK REMOVAL See Figures 12, 13, and 14. Whenever necessary to remove the chuck for replacement, etc., use the following procedure for chuck removal: 1. UNPLUG YOUR HAMMER DRILL. W ARNING: Failure to unplug your hammer drill could result in accidental starting causing serious injury. 2. Open chuck jaws. Insert a 5/16 inch or ...
-
Ryobi HD500 - page 12
Page 12 MAINTENANCE GENERAL Avoid using solvents when cleaning plastic parts. Most plas- tics are susceptible to damage from various types of commer- cial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc. W ARNING: Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, ...
-
Ryobi HD500 - page 13
Page 13 NOTES ...
-
Ryobi HD500 - page 14
972000-401 8-97 Printed In U.S.A. OWNER'S OPERA TING MANUAL 1/ 2 in. (13 mm) Hammer Drill - HD500 DOUBLE INSULA TED • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Factory Service Center or Authorized Service Organization. Be sure to provide all pertine ...
¿Tienes una pregunta acerca de Ryobi HD500?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Ryobi HD500, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Ryobi HD500 probablemente compartirá una forma de solucionarlo.