-
Hans Grohe 35116801 - page 1
Installation Instructions / W arranty Steel 35115801 Steel 35116801 ...
-
Hans Grohe 35116801 - page 2
2 W all Mounted Single-Handle Lav Set with Base Plate 35115801 W all Mounted Single-Handle Lav Set 35116801 35115801 35116801 T echnical Data Max. flow rate: 2 .2 g p m Max. water pressure: 147 psi Recommended pressure: 14.7 - 72 psi T est pressure: 232 psi Max. hot water temperature: 176° F* Recommended hot water temp.: 120° F - 140° F* Require ...
-
Hans Grohe 35116801 - page 3
3 Installation with 38111181 rough manufactured before 03/2004 T urn the water off at the supply before beginning this installation. Remove the covers from the plaster shields (1). T rim the plaster shields so that they extend 1/16” out- side the surface of the finished wall (2). Seal the wall around the plaster shield with waterproof sealant. Us ...
-
Hans Grohe 35116801 - page 4
4 Install the new cup washers and springs in the rough. Install the cartridge assembly . Installation with 38111181 rough manufactured after 04/2004 Remove the covers from the plaster shields. T rim the plaster shields so that they extend 1/16” outside the surface of the finished wall. Seal the wall around the plaster shield with waterproof seala ...
-
Hans Grohe 35116801 - page 5
5 Install the cartridge and anti-twist device in the housing. Install the cup washers and springs in the rough. Install the cartridge assembly . Installation with all models: Push the handle over the cartridge stem. Tighten the handle screw with a 2 mm Allen wrench. If you are installing 35115801, turn to page 6. If you are installing 35116801, tur ...
-
Hans Grohe 35116801 - page 6
6 Model 35115801 only: Measure the distance between the wall surface and the end of the handle (x). If x is between 3 1/4” and 3 7/8”, select the two “A” sleeves (1 1/4”). If x is between 3 7/8” - 4 3/8”, select the two “B” sleeves (7/8”). If x is greater than 4 3/8”, select the two “C” sleeves (1/2”). x A B C 1 1/4” 7 ...
-
Hans Grohe 35116801 - page 7
7 Connect the fixation nuts to the sleeves. Measure the distance from the rough to the outside surface of the finished wall (X) (1). Add 1 3/16” to X. Cut the spout connecting thread so that it is X + 1 3/16” long (2). W rap the connecting thread with T eflon tape. Install the mounting thread. T ighten with an 8 mm Allen wrench. 1. 2. ...
-
Hans Grohe 35116801 - page 8
8 T ighten the retaining nuts with the ser vice key . Lightly lubricate the o-rings on the spout and handle escutcheons with the enclosed lubricant (1). Push the escutcheons onto the baseplate (2). Push the baseplate against the wall (1). Thread the sleeves into the rough (2). 1. 2. 2. 1. ...
-
Hans Grohe 35116801 - page 9
9 Push the spout over the connecting thread (1). T ighten the set screw with a 3 mm Allen wrench (2). Install the handle flange (3). 1. 2. 3. ...
-
Hans Grohe 35116801 - page 10
10 Model 35116801 only: Measure the distance between the wall surface and the end of the handle (x). If x is between 3 1/4” and 3 7/8”, select the “A” sleeve (1 1/4”). If x is between 3 7/8” - 4 3/8”, select the “B” sleeve (7/8”). If x is greater than 4 3/8”, select the “C” sleeve (1/2”). x A B C 1 1/4” 7/8” 1/2” ...
-
Hans Grohe 35116801 - page 11
11 Push the sleeve / handle escutcheon assembly into place over the handle (1). T ighten it by rotating it clockwise (2). Push the flange over the handle. Push the sealing ring into the handle escutcheon (1). Install the handle escutcheon onto the sleeve (2). 1. 2. 1. 2. ...
-
Hans Grohe 35116801 - page 12
12 Measure the distance from the rough to the outside surface of the finished wall (X) (1). Add 1 3/16” to X. Cut the spout connecting thread so that it is X + 1 3/16” long (2). W rap the spout connecting thread with T eflon tape. Install the spout connecting thread. T ighten it with an 8 mm Allen wrench. Install the spout escutcheon and spout ...
-
Hans Grohe 35116801 - page 13
13 35115801 User Instructions Pivot the handle up to turn the water on, down to turn it off. Pivot the handle to the left for warmer water , to the right for cooler water . on off 1 2 3 4 5 6 7 8 9 10 11 12 13 17 ...
-
Hans Grohe 35116801 - page 14
14 Replacement Parts 35116801 1 flange 96908800 2 handle 35094800 3 handle escutcheon 96912800 4 spout escutcheon 96913800 5 baseplate 96927800 6 cartridge 96339000 7 aerator 96683800 8 spout 97282800 9 anti-twist device 97280000 10 connecting thread 97230000 11 extension kit 38982000* 12 set screw 97660000 13 nut 97601000 14 handle escutcheon 9690 ...
-
Hans Grohe 35116801 - page 15
15 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY ...
-
Hans Grohe 35116801 - page 16
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770 360-9880 • Fax 770 360 9887 www .hansgrohe-USA.com US - Installation Instructions • Part No. 90505801 • Revised 08/2007 including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year , with respect to Hansgrohe and Commercial pr ...
¿Tienes una pregunta acerca de Hans Grohe 35116801?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hans Grohe 35116801, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hans Grohe 35116801 probablemente compartirá una forma de solucionarlo.