Español dropdown-ico

Manual de instrucciones Troy-Bilt 42031

32 de páginas 0.62 mb
Descargar

Pasar a la página of 32

Summary
  • Troy-Bilt 42031 - page 1

    Models 42010 - 8 HP , 24" Auger 42030 - 8 HP , 24" Auger 42012 - 10 HP , 26" Auger 42031 - 10 HP , 26" Auger Owner/Operator Manual Snowthrower • Safety • Assembly • Controls • Operation • Maintenance ® GARDEN WAY INCORPORATED ...

  • Troy-Bilt 42031 - page 2

    2 Dear Owner: Thank you for purchasing this product. The unit was carefully designed and manufactured to provide excellent performance if properly operated and maintained. Read this manual. This is a safety , operation and general maintenance manual which does not attempt to cover major repairs. This manual is considered a permanent part of the uni ...

  • Troy-Bilt 42031 - page 3

    3 T able of Contents SECTION 1: SAFETY ..................................................................... 4 Safety Decals ............................................................................................................ 7 SECTION 2: ASSEMBLY ................................................................. 8 Inspect Unit/Tools Require ...

  • Troy-Bilt 42031 - page 4

    T raining 1. Read this owner/operator manual and the separate engine owner manual carefully before operating the unit. Be completely familiar with the controls and the proper use of the unit. A replacement manual is available by contacting the factory. 2. Never allow children or untrained adults to use the unit. 3. Keep the area of operation clear ...

  • Troy-Bilt 42031 - page 5

    5 Section 1 : Safety 3. Before starting the engine, check the tightness of all screws, nuts, bolts, and other fasteners. Replace or clean any damaged or unreadable safety and operating labels. 4. Wear adequate winter outer garments when operating the unit. Wear footwear that will improve footing on slippery surfaces. Exercise caution to avoid slipp ...

  • Troy-Bilt 42031 - page 6

    6 11. Before inspecting the unit or making any adjustments, or if the unit jams or becomes clogged, shut the engine off immediately and allow all moving parts to come to a stop. Disconnect the spark plug wire from the spark plug and secure the wire away from the spark plug. Use only a wooden stick (at least 3 feet long) to clear away any blockage. ...

  • Troy-Bilt 42031 - page 7

    7 Section 1 : Safety 5. Allow the engine to cool before storing in any enclosure. 6. Store gasoline in a cool, well- ventilated area, safely away from any spark- or flame-producing equipment. 7. Store gasoline only in an approved gasoline storage container, safely out of the reach of children. 8. Use only original equipment replacement parts. Parts ...

  • Troy-Bilt 42031 - page 8

    Assembly 8 Section 2 IMPORTANT: Follow the assembly steps carefully. Contact the factory or your local authorized dealer if you have any questions or problems. A. Inspect Unit Inspect the unit and shipping crate for damage immediately after delivery. Contact the carrier (trucking company) if you find or suspect damage. Inform them of the damage and ...

  • Troy-Bilt 42031 - page 9

    9 Section 2: Assembly A J B C E F D G H I IMPORTANT: Left and right sides of the unit are determined from the operator position, facing the direction of forward travel. E. Install Handlebars 1. Cut the plastic cable ties securing the handlebar ends to the chassis and remove the handlebars. Remove the protective wrapping on the handlebars. 2. Attach ...

  • Troy-Bilt 42031 - page 10

    10 Section 2: Assembly F . Install Discharge Chute 1. Remove the cardboard packing shield from the discharge chute mount opening. 2. Loosen (do not remove) the left and right side sets of plastic shims (G, Fig. 2-4, inset A) and plastic hold-down clips (H, Fig. 2-4, inset A) on the toothed flange (J) of the discharge chute assembly. Remove and save ...

  • Troy-Bilt 42031 - page 11

    11 Section 2: Assembly Fig. 2-7 Y Fig. 2-8 AH AC AD AB AA AT AS AG R AF AE 5. Rotate the chute control crank (Z, Fig. 2-6). The deflector chute should turn freely. Adjust the worm gear assembly bracket (L, Fig. 2-4) as necessary to prevent binding. H. Attach Auger Drive Control Rod 1. Remove the plastic cable tie that secures the auger drive contro ...

  • Troy-Bilt 42031 - page 12

    12 Section 2: Assembly Fig. 2-9 AF AB Yellow Yellow & Red Wires AL AO AN AM AK Black Black Blue Red Fig. 2-10 I. Attach Wheel Drive Control Rod 1. Remove the plastic cable tie that secures the wheel drive control rod (AE, Fig. 2-8) and the gear shift control rod (AF) to the left handlebar. 2. Hook the spring (AG, Fig. 2-8) at the lower end of t ...

  • Troy-Bilt 42031 - page 13

    13 Section 2: Assembly K. Wiring Harness Installation 1. Remove the plastic cable tie that secures the wiring harness to the right handlebar. 2. Route the wiring harness to the inside of the right handlebar and over to the right side of the engine. 3. Attach the ring terminal (AK, Fig. 2-10) on the two black wires to the screw on the engine shroud ...

  • Troy-Bilt 42031 - page 14

    14 Controls This section defines the various controls on the unit. Refer to the following section, “Operation,” for an explanation of the proper use of these controls. A, Fig. 3-1—Wheel drive control lever Controls the engagement of the wheel drive. When this lever is down against the handlebar and the engine is running, the wheels will rotat ...

  • Troy-Bilt 42031 - page 15

    15 Section 3: Controls H, Fig. 3-4—Throttle Located on back left corner of the engine, the throttle controls the speed of the engine. For proper operation information, refer to the following section, “Operation.” NOTE: The engine lubrication and cooling systems operate best at full throttle. Operating the engine at less than full throttle for ...

  • Troy-Bilt 42031 - page 16

    Operation 16 Pre-operation checklist 1. Review Section 1, “Safety” and Section 3, “Controls” in this manual. 2. Check the unit for any loose or missing hardware. Tighten or replace as needed. 3. Check inside the auger housing and the discharge chute and remove any debris. 4. Check the engine oil level: a. Move the unit onto a level surface. ...

  • Troy-Bilt 42031 - page 17

    17 Section 4: Operation Fill the fuel tank with fresh, clean unleaded gasoline with a minimum octane rating of 87. Leave 1/2" of space for fuel expansion. DO NOT MIX OIL WITH GASOLINE! Tighten the gasoline fill cap securely. Refer to the engine owner manual for additional gasoline information. DO NOT MIX OIL WITH GASOLINE! 6. The unit should b ...

  • Troy-Bilt 42031 - page 18

    18 Starting the engine 1. Review the “Pre-operation checklist” earlier in this section. Move the unit outside to a well-ventilated, level area. 2. Move the gearshift lever (B, Fig. 4-4) into the desired gear position. 3. Turn the ignition key (C, Fig. 4-4) to the RUN “ ” position. 4. Turn choke knob “ ” (D, Fig. 4-5) clockwise to FULL C ...

  • Troy-Bilt 42031 - page 19

    19 Auger drive engagement 1. Remove any debris from inside the auger housing. 2. Adjust the discharge chute deflector cap (RR, Fig. 4-6) angle with adjustment lever (SS, Fig. 4-6). The discharge chute deflector cap should usually be adjusted to a low angle, so it is not pointing at any persons, animals, buildings or vehicle, especially in windy con ...

  • Troy-Bilt 42031 - page 20

    20 Section 4: Operation T ransporting the unit Release the auger drive control lever to disengage the auger drive whenever the unit is being transported to the work site. The unit is extremely heavy. Have at least one other person help you when loading or unloading the unit into a truck or trailer. Use ramps when loading or unloading the unit onto ...

  • Troy-Bilt 42031 - page 21

    Maintenance 21 Engine oil Check the engine oil level each time before starting the unit and after each 5 hours of operation. To check the engine oil level: 1. Move the unit onto a level surface. 2. Remove the oil dipstick (A, Fig. 5-1). 3. Wipe the oil from the dipstick with a clean cloth. 4. Screw the dipstick back into the engine. 5. Remove the o ...

  • Troy-Bilt 42031 - page 22

    22 Section 5: Maintenance Lubrication At the beginning and end of each season or after every 25 hours of operation, lubricate the unit as recommended below: 1. Lightly oil both the deflector chute cap pivot points (D, Fig. 5-3). 2. Lightly oil the discharge chute control rod pivot points where the control rod enters the control panel bearing (E, Fi ...

  • Troy-Bilt 42031 - page 23

    length of spring (W, Fig. 5-6) again. The spring length should now measure 5/8" – 3/4" (15–19mm) longer than the measurement taken in step 2. If it does not, loosen jam nut (Y, Fig. 5-6) and turn adjuster (Z, Fig. 5-6) to increase or decrease the spring length. (1-1/4 turns of the adjuster equals 1/16" [1.5mm] of spring extension ...

  • Troy-Bilt 42031 - page 24

    24 Auger Drive Belt Adjustment Due to wear, the auger drive belt may begin to slip when the auger drive lever is engaged. To adjust the auger drive belt: 1. Perform the brake arm adjustment as described later in this section. 2. If assembling a new unit, raise the wheel drive control lever (AP, Fig. 5-9) and the auger drive control lever (AL). 3. P ...

  • Troy-Bilt 42031 - page 25

    25 Section 5: Maintenance 5. Remove the auger drive belt from the lower drive pulley (AO). 6. Remove the belt from unit. To install the auger drive belt: 1. Position the auger drive belt (AD) down through gap. Position the belt into the lower drive pulley (AO). 2. Position the auger drive belt (AD) into pulley (AE). Reinstall the belt guide (AC) an ...

  • Troy-Bilt 42031 - page 26

    26 Section 5: Maintenance Brake Arm Adjustment The brake arm adjustment is set at the factory to 1/16 - 1/8” for proper belt/brake clearance. Due to wear this may need adjustment. To perform this adjustment: 1. Remove the bolts, flat washer, lock washer and belt cover (AB, Fig. 5-9). 2. Squeeze the auger drive control lever (AL, Fig. 5-9) against ...

  • Troy-Bilt 42031 - page 27

    27 Section 5: Maintenance POSSIBLE PROBLEM Ignition key in STOP position Choke knob in incorrect position Engine throttle lever in incorrect starting position Engine not primed enough (when cold) Engine primed too much (when cold) Spark plug wire disconnected Fouled or faulty spark plug Gasoline tank empty Fuel shutoff valve is closed Carb / fuel l ...

  • Troy-Bilt 42031 - page 28

    28 Section 5: Maintenance TROUBLE Auger drive control lever does not engage auger drive Auger spins with drive lever disengaged Wheel drive control lever does not turn wheels Wheels turn with wheel drive control lever disengaged Snowthrower does not throw snow well Snowthrower does not clear snow Snowthrower makes sloping cut in snow Electric start ...

  • Troy-Bilt 42031 - page 29

    29 Section 5: Maintenance Interval Before each use After each use Every 25 hours of operation or annually Every 50 hours of operation or annually Annually Item Engine oil All fasteners Auger drive lever Wheel drive lever Handlebar control levers and linkages Snowthrower Engine oil Tires Auger gear box Belts Cooling air screen Spark plug Drive chain ...

  • Troy-Bilt 42031 - page 30

    30 Specifications Snowthrower Models 42010, 42012, 42030, & 42031 Snowthrower Height ......................To top of handlebar levers: 41.5" (105.3 cm) ...........w/o handlebars, deflector cap down: 33" (83.75 cm) Length........................................With handlebars: 70" (177.6 cm) ....................................Wit ...

  • Troy-Bilt 42031 - page 31

    31 Specifications Wiring Diagram DIODE/RECTIFIER ENGINE CONNECTOR RED BLUE IGNITION SWITCH HANDLEBAR HEATER HANDLEBAR HEATER GROUND TO HANDLEBAR BLACK To Light (optional) BLACK RED RED YELLOW RED YELLOW ENGINE SHROUD GROUND SCREW ENGINE CONNECTOR RED GREEN OFF ON TO MAGNETO TO ENGINE STATOR ...

  • Troy-Bilt 42031 - page 32

    For customer assistance, contact your nearest authorized dealer or: GARDEN WAY INCORPORATED • 1 Garden Way • Troy, New York U.S.A. 12180 Customer Service: 1-800-437-8686 • Technical Service: 1-800-520-5520 • Parts Service: 1-800-648-6776 • FAX: (518) 391-7332 Outside the U.S.A. and Canada: Customer Service: (518) 391-7007 • For Technica ...

Fabricante Troy-Bilt Categoría Snow Blower

Los documentos del dispositivo Troy-Bilt 42031 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Troy-Bilt
- manuales de instrucciones 42031
- hojas de producto Troy-Bilt
- folletos informativos
- o etiquetas energéticas Troy-Bilt 42031
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Troy-Bilt 42031.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Troy-Bilt 42031, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Troy-Bilt 42031. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Troy-Bilt 42031.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Troy-Bilt 42031, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Troy-Bilt 42031. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Troy-Bilt 42031.

El manual de instrucciones completo de Troy-Bilt debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Troy-Bilt 42031 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Troy-Bilt 42031, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Troy-Bilt 42031 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Troy-Bilt 42031 - que deben facilitarnos los primeros pasos durante el uso de Troy-Bilt 42031
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Troy-Bilt 42031
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Troy-Bilt 42031 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Troy-Bilt 42031?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Troy-Bilt 42031, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Troy-Bilt 42031 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)