-
Master Lock MK-470 - page 1
Manual Part No. 156934 Revision 10/01 Model MK-470 T ile Saw Owner ’s Manual Parts List & Operating Instructions serial number R For your warranty to be effective, complete the warranty card (include the serial number) and mail it in as soon as possible. please record the serial number (Located on the cover post casting) of your saw in this b ...
-
Master Lock MK-470 - page 2
T a b l e o f C o n t e n t s Foryour safety, read all instructions! These safety precautions should be followed at all times. Failure to follow these safety precautions could result in injury to yourself and others. Safety is a combination of operator common sense and alertness at all times when the saw is being used. I M P O R TA N T S A F E T Y ...
-
Master Lock MK-470 - page 3
Safety labels are located according to the drawing below. The labels contain important safety information. Please read them carefully. These labels are considered a permanent part of your saw. If a label comes off or becomes hard to read, contact MK Diamond or your dealer for replacement. D a m a g e p r e v e n t i o n m e ss a g e s Cali fornia P ...
-
Master Lock MK-470 - page 4
3 Carefully open carton. Remove the accessory pack. Lift the saw out of the carton by the pan, and place onto a level work surface. Open the accessory pack, and check each item with the contents list and illustration below, making certain that all items are accounted for and in good condition before discarding any packing material. If there are any ...
-
Master Lock MK-470 - page 5
The MK-470 tile saw is wired for 120V, single phase operation, and draws 5.3 amps at 120V. This is not a large load, however if the machine is operated on any circuit that is already close to its capacity, the circuit breaker may be tripped. If this occurs, eliminate other loads from the circuit. A separate circuit protected by a 20 amp breaker is ...
-
Master Lock MK-470 - page 6
S a w i n g O pe r a t i o n s G e n e r a l C u t t i n g G u i d e l i n e s • A diamo nd bl ade does n ot cut, it grinds. Do not force the tile into the blade, nor feed it to quickly . • Di am o n d b lade s a re n o t all al ike. M a tch the M K bl a d e to th e pro duct to be cut. • B e f o r e mounting an y blade on the saw , inspec t t ...
-
Master Lock MK-470 - page 7
Do not attempt to cut pieces too small to hold by hand outside the blade guard. Avoid awkward hand positions where a sudden slip could cause a hand or fingers to come in contact with the blade. When cutting any material, make sure it is fully supported. Hold workpiece firmly against the fence. Only feed the material as fast as the blade is able to ...
-
Master Lock MK-470 - page 8
Optiona l Ac cesso ries wate r flow problems Check that the water pump vibrates when the motor is on. Reprime pump: Take water hose off blade guard, r emove air bubbles, fully submerse pump outlet in water, turn motor on. Plug the water pump into an electrical outlet, fully submerse pump in water and check it’s operation. Check that the water jet ...
-
Master Lock MK-470 - page 9
t i l e s a w B2 X4 B3 B4 H4 G4 G2 G3 G1 H5 X3 A7 H6 H5 A3 B1 B5 B4 K7 K6 X2 X2 X2 K5 K8 X2 K3 X2 K4 K1 X2 K2 X2 E3 E4 E2 X2 J2 J1 J3 L3 L2 L4 H3 H1 L1 E 1 F 1 MK-470 Exploded View N3 N4 N1 E2 E3 E4 D2 D1 X2 F4 X2 F3 F2 X2 H2 M1 A1 A2 D3 ...
-
Master Lock MK-470 - page 10
9 MK-470 Parts List Model MK-470 Tile Saw 120v/7.4a, Part # 155779 Item Description Qt y Part # A1 Wrench, Blade Nut, 15/16 Boxed End 1 134684 A2 Wrench, Blade Shaft, 11/16 Open End 1 153450 A3 Blade, 7 Dia X 5/8 Arbor 1 153441 A4* Owner’s Manual 1 156934 A5* Warranty Card 1 155037 A6* Information Tag 1 155844 A7 Assembly, Rip Guide w/ Screw, _-2 ...
-
Master Lock MK-470 - page 11
10 K5 Wheel, Roller 2 151799 K6 Screw, 1/4-20 X 1 1/4 Hex Head Cap 2 157145 K7 Washer, 1/4 SAE Flat 2 151915 K8 Nut, 1/4-20 Hex 2 151893 L Assembly, Splash Curtain 1 155901-MK L1 Curtain, Splash 1 134841 L2 Bracket, Splash Curtain 1 155901 L3 Washer, 1/4 SAE Flat 1 151915 L4 Wingscrew, 1/4-20 X 1/2 1 151888 M Table, 470 1 156536 N Assembly, PES-100 ...
-
Master Lock MK-470 - page 12
1315 Storm Parkway. Torrance, CA 90509-2803 1 (800) 421-5830 F AX 1 (310) 539-5158 (310) 539-5221 www.mkdiamond.com MK Diamond Products, Inc. R HOW TO ORDER PARTS Please have the following information ready before calling: SERIAL NUMBER OF YOUR SA W MODELNUMBER OF SAW WHERE PURCHASED AND WHEN PAR T NUMBER PAR T DESCRIPTION All parts listed may be o ...
¿Tienes una pregunta acerca de Master Lock MK-470?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Master Lock MK-470, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Master Lock MK-470 probablemente compartirá una forma de solucionarlo.