-
Porter-Cable 7537 - page 1
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...
-
Porter-Cable 7537 - page 2
2 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some example of these chemicals are: ● ● lead from lead-based paints ● ● crystalline silica from bricks and cement and other maso ...
-
Porter-Cable 7537 - page 3
3 3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 4. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the ris ...
-
Porter-Cable 7537 - page 4
4 SERVICE 1. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 2. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance Section of this manual. Use of unauthorized parts or failure to follow Main ...
-
Porter-Cable 7537 - page 5
5 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts µ F ........................ microfarads l ........................ liters kg ........................ kilograms N/cm 2 ........................ newtons per ...
-
Porter-Cable 7537 - page 6
6 RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS Length of Cord in Feet 115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft. 230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft. 0-2 18 18 18 16 16 14 14 12 12 2-3 18 18 16 14 14 12 12 10 10 3-4 18 18 16 14 12 12 10 10 8 4-5 18 18 1 ...
-
Porter-Cable 7537 - page 7
7 Fig. 1 B A 7. To remove the bit, reverse the foregoing procedure. If bit does not remove easily, tap the collet nut with wrench to release. AVOID POSSIBLE DAMAGE TO COLLET. NEVER TIGHTEN COLLET WITHOUT BIT. ASSEMBLING THE MOTOR IN THE ROUTER BASE EQUIPPED WITH TWO HANDLES 1. DISCONNECT MOTOR FROM POWER SOURCE. 2. Loosen the clamp screw (A) Fig. 1 ...
-
Porter-Cable 7537 - page 8
8 Fig. 4 C Fig. 5 F B D C A E ADJUSTING DEPTH OF CUT 1 . DISCONNECT TOOL FROM POWER SOURCE. 2. Loosen clamp screw (A) Fig. 5. 3 . While holding base (E), turn motor unit (F) Fig. 5 COUNTERCLOCKWISE until the tip of the bit is above bottom surface of base. 4. Set router on flat wood surface. 5 . Turn motor unit (F) Fig. 5 CLOCKWISE until bit touches ...
-
Porter-Cable 7537 - page 9
9 ST ARTING AND STOPPING THE MOTOR Before starting the tool, clear the work area of all foreign objects. Also keep firm grip on tool to resist starting torque. The motor units for these routers can be used with either the base having two handles or the base with the switch-in-handle. To avoid personal injury and/or damage to finished work, always a ...
-
Porter-Cable 7537 - page 10
10 Fig. 8 Fig. 9 B B D D C A The speed and depth of cut will depend largely on the workpiece. Keep the cutting pressure constant but do not crowd the router so the motor speed slows excessively. On exceptionally hard woods or problem materials, more than one pass at various settings may be necessary to get the desired depth of cut. When making cuts ...
-
Porter-Cable 7537 - page 11
11 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear safety glasses while using compressed air. F AILURE TO ST ART Should your tool fail to start, ch ...
-
Porter-Cable 7537 - page 12
12 A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter- Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since accessories other than those offered by Porter- Cable ? ...
-
Porter-Cable 7537 - page 13
13 AB C Distance Model No. ID OD Past Base 42021 1 1 / 32 "1 1 / 4 " 7 / 16 " 42024 21 / 32 " 3 / 4 " 9 / 16 " 42027 11 / 32 " 7 / 16 " 5 / 32 " 42030 25 / 32 "1 " 3 / 8 " 42033 13 / 32 " 1 / 2 " 5 / 16 " 42036 9 / 32 " 3 / 8 " 5 / 16 " 42039 3 / 4 " 59 / ...
-
Porter-Cable 7537 - page 14
14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material du ...
-
Porter-Cable 7537 - page 15
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...
¿Tienes una pregunta acerca de Porter-Cable 7537?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Porter-Cable 7537, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Porter-Cable 7537 probablemente compartirá una forma de solucionarlo.