-
Pelco PT573 - page 1
Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 PT573 Series Medium Duty Pan/Tilt Installation/ Operation Manual C332M-D (10/98) ...
-
Pelco PT573 - page 2
2 Pelco Manual C332M-D (10/98) REVISION HISTOR Y Manual # Date Comments C332M 9/89 Original version. C332M-A 10/91 Rev . A. Re vised to include model PT573-24R/HB. C332M-B 5/95 Rev . B . Section 4.4, Connector Assembly , re vised. Figures 7-9 revised. to reflect new ground wire color (green). Sec- tion 6.3, Drive/Chain Maintenance, added. Standardi ...
-
Pelco PT573 - page 3
Pelco Manual C332M-D (10/98) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be obser ved. 1. Installation and servicing should only be done by qualified ...
-
Pelco PT573 - page 4
4 Pelco Manual C332M-D (10/98) 2.0 DESCRIPTION The PT573R and the PT573-24R are medium duty , indoor/outdoor pan/tilts de- signed f or V330APT retrofit applications. Both units feature rugged worm gear final drives to minimize bac klash and prev ent wind dr ift, and are fully adjustable f or wear . They also ha ve adjustable dur ation (2-9 seconds) ...
-
Pelco PT573 - page 5
Pelco Manual C332M-D (10/98) 5 NOTE: When mounting the pan/ tilt outdoors in the inv er ted position (base up), R TV silicone sealant, such as Dow Corning T ype 732 or equivalent, should be applied to the areas indicated in Figure 1. 3.0 INST ALLA TION The PT573R and PT573-24R are designed to mount onto a horizontal surface in the upright or invert ...
-
Pelco PT573 - page 6
6 Pelco Manual C332M-D (10/98) REQUIRES EXTERNAL POWER SUPPL Y Ta b le A. Requirements to Wire P ower to P an and Tilt Motors Model Wire Size Maximum Distance "A" Maximum Distance "B" Maximum Distance "B" (A WG) (5 Conductors*) (6 Conductors**) PT573R 20 5,800 ft (1,768 m)*** 1,045 ft (318.52 m) 2,080 ft (633.98 m) (12 ...
-
Pelco PT573 - page 7
Pelco Manual C332M-D (10/98) 7 Figure 2. Connector Assembly 3.3.1 Mating Connector Assembly To assemb le the mating connectors, ref er to Figure 2 and perform the f ollowing steps. The instructions that follo w apply to all AMP style connectors regardless of pin size or pin number . 1. Slide the connector clamp assembly o v er the conductor cab le. ...
-
Pelco PT573 - page 8
8 Pelco Manual C332M-D (10/98) T TO FRAME SCAN CIRCUIT BOARD 4 13 14 11 12 2 10 3 7 P1 VIO RED BLU BRN/W ORG YEL BRN GRN 75W M2 C2 C3 S3 S4 S2 S1 BLU/W C1 M1 AU TO LEFT RIGHT COM UP DOWN COM GND AC NEUT 120 V A C 8 6 5 1 2 3 4 12 15 16 Figure 3. PT573R/PT573-24R Wir ing Schematic ...
-
Pelco PT573 - page 9
Pelco Manual C332M-D (10/98) 9 NO TE: CO VER PLA TE IS NOT SHO WN. 3.4 LIMIT STOP ADJUSTMENTS To set pan/tilt limit stops , perf orm the following steps . Ref er to Figure 4. 1. Loosen the pan limit stops. 2. T urn the control unit on. Pan the unit to the right until the desired right pan limit is reached. 3. Mov e the right pan limit stop until it ...
-
Pelco PT573 - page 10
10 Pelco Manual C332M-D (10/98) Figure 5. Fr ame Scan Adjustment Location 3.5 FRAME SCAN ADJUSTMENT Fr ame scan duration is set at the factory for appro ximately four seconds . Y ou can adjust the scan duration to operate between tw o and nine seconds. To adjust the frame scan dur ation: 1. Remov e the three screws on the front of the pan/tilt hous ...
-
Pelco PT573 - page 11
Pelco Manual C332M-D (10/98) 11 4.0 OPERA TION Refer to the manual for your control equipment for operating the pan/tilt. ...
-
Pelco PT573 - page 12
12 Pelco Manual C332M-D (10/98) 5.0 TROUBLESHOOTING Some common problems encountered with pan/tilt systems include mis wir ing, over- loading, and not using the units for the correct application. If the pan/tilt unit fails to operate, do the f ollowing: 1. Check the fuse in the control unit. If the fuse is bad, replace it. 2. If the fuse blo ws aft ...
-
Pelco PT573 - page 13
Pelco Manual C332M-D (10/98) 13 6.0 MAINTENANCE Inspect the pan/tilt unit ev ery six months to ensure trouble-free operation and an e xtended product lif e. Harsh environments and/or continuous motion applications may require more frequent maintenance . Please read all of the instructions that follow bef ore servicing the pan/tilt. To begin, remove ...
-
Pelco PT573 - page 14
14 Pelco Manual C332M-D (10/98) 7.0 SPECIFICA TIONS GENERAL Construction: Aluminum plate, all internal par ts corrosion protected Dimensions: See Figure 7 Environment: Indoor/outdoor T emperature: -10 ° F to 140 ° F (-23 ° to 60 ° C) W eight Unit: 22 lb (9.9 kg) Shipping: 25 lb (11.5 kg) MECHANICAL Pa n Horizontal Mov ement: 0-355 ° Speed: 6 ? ...
-
Pelco PT573 - page 15
Pelco Manual C332M-D (10/98) 15 Connectors: Amp CPC type, mate supplied Motors: Two-phase induction type, continuous duty, instantaneous reversing Limit Switches: Pan and tilt – 5 amp, 10 million cycle rating (external adjust- ment) Conductor Requirements: 6 (7 if two wires are used for motor common) plus ground, unshielded Figure 7. Dimension Dr ...
-
Pelco PT573 - page 16
16 Pelco Manual C332M-D (10/98) 8.0 WARRANTY AND RETURN INFORMA TION W ARRANTY P elco will repair or replace , without charge, any merchandise prov ed defectiv e in material or wor kman- ship for a period of one year after the date of shipment. Exceptions to this warranty are as noted belo w: • Five years on FT/FR8000 Series fiber optic products ...
¿Tienes una pregunta acerca de Pelco PT573?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Pelco PT573, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Pelco PT573 probablemente compartirá una forma de solucionarlo.