-
PYLE Audio PP-7200L - page 1
Part 1 FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply wit h limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are ...
-
PYLE Audio PP-7200L - page 2
Part 2 GE TTING STARTED CONGRATULATION You have made a very wise decision by purchasing the easy loading; low noise; high resolution; light weight; high reliability thermal printer Aura (PP - 7000 II, PP - 7200L, PP - 7000U & PP - 7200U ) ser ies of Posiflex products. This series of printers has been elegantly designed for a Point - Of - Sale, ...
-
PYLE Audio PP-7200L - page 3
Part 3 UNPACKING Followings are items you may find when you carefully unpack the carton that delivers Aura series printer. If there is any discrepancy or problem, contact your dealer immediately. Be sure to save the packing materials in case the printer needs to be shipped at some point in the future . 1). The printer itself 2). Thermal paper test ...
-
PYLE Audio PP-7200L - page 4
Part 4 PRODUCT PICTURES Top View Front View Bottom View Rear View 7 3 4 1 PP - 7000 U 6 6 7 4 10 PP - 7 2 00 U 3 1 Bottom Cover Power LED Error LED Paper Out LED FEED Switch Top Hood Top Cover Hood Release Power Switch Cutter Cover PP - 7000 II 2 3 1 4 5 8 4 3 1 PP - 7 2 00 L 9 Front View Bottom View Power Switch Screws Window Plate Screw Setup Win ...
-
PYLE Audio PP-7200L - page 5
Part 5 The numbered items above are: 1). Power Connector 2). Parallel Connector 3). Frame Ground 4). Peripheral Connector 5). Serial Connector 6). Interface Bracket Screw 7). USB Connector 8). LAN Connector 9). Reset Pin Hole 10). Service Serial Port Cable Cover INDICATORS • Power LED: gr een • Error LED: red • Paper Out LED: red Tenon Tenon ...
-
PYLE Audio PP-7200L - page 6
Part 6 QUICK START - UP LOADING PAPER Desk Top Application 1. Slide the hood lock toward the front of the printer to release the hood as in Pix. 1 . 2. Raise the released hood wide open manually as in Pix. 2 . 3. Drop the thermal pap er roll inside the printer in orientation as shown in Pix. 2 . 4. Close the hood back leaving the tail of the paper ...
-
PYLE Audio PP-7200L - page 7
Part 7 right in the picture above. Apply the male connector of RS232 cable to this port for serial application. Please note that when serial connection is used, there must be no cable co nnection at the parallel port on the printer. The default protocol used in serial connection is 19200 bps, none parity, 8 data bits, 1 stop bit. Set in setup windo ...
-
PYLE Audio PP-7200L - page 8
Part 8 Use the normal USB Cable (P/N: 21863250800) to connect to a normal USB port or the normal USB portion of the powered USB connector of host system . The power adaptor is require d in this normal USB application. Use the powered USB cable to connect a +24V Powered USB port of Posiflex POS system with the powered USB plug, and connect to the US ...
-
PYLE Audio PP-7200L - page 9
Part 9 Install Cable Cover Check the bottom view of the printer, the 4 screws for the printer itself are in quite deep holes. Insert the tenons of the cable cover into the 2 printer screw holes nearest to the connection area. Apply a cable cover fixing screw at the matched screw holes as circled in the bottom view picture at right. Power On When al ...
-
PYLE Audio PP-7200L - page 10
Part 10 position of sensor head. The acceptable paper roll bobbin outer diameter is between 18 and 22mm. This adjustment allows sensor activation on paper roll overall diameter between 21 and 23.6 mm unless for too light bobbins. Reme mber, for smaller roll diameter, the sensor head should go higher. Paper Roll Replacement When the paper roll to pu ...
-
PYLE Audio PP-7200L - page 11
Part 11 INSTALLING DRIVER There w ill always be a Posiflex Product Information CD or a separate CD of similar nature but specifically created for the product delivered. Please find the appropriate subfolder from the non - specific Posiflex Product Information CD and check the information fil e like “ readme ” or installation guide or applicatio ...
-
PYLE Audio PP-7200L - page 12
Part 12 OPER ATI ON GUIDE MAINTENANCE GUIDE LINES • Always turn off and disconnect power before opening the cover. • The areas around the print head and motor become very hot during and just after printing, DO NOT touch them. • When handling the interior of the thermal printer, please pay attention not to be hurt by any sharp edge of the meta ...
-
PYLE Audio PP-7200L - page 13
Part 13 possible cause for the flashing Error LED is that the printer has been p rinting for quite a period of time and the print head temperature become too high. After few minutes under normal ventilation, the print head should be able to cool down and the Error LED will stop flashing. Printing will resume after cooled down. If this is not the ca ...
-
PYLE Audio PP-7200L - page 14
Part 14 baud rate could be a smart decision to this situation. (No need to change baud rate if n o trembling occurs to eliminate possible data error rate.) Paper Jam Problems Paper is jammed inside the printer – Turn off the printer and open the print hood by releasing the hood lock. Remove the jammed paper and reinstall the paper roll. Close the ...
-
PYLE Audio PP-7200L - page 15
Part 15 Phillips screwdriver at the right side of the print mechanism. When the cutter blade returns to its standard position, a hole in the plastic gear will show up in the window as illustrated in diagram C b elow. Close the cutter cover when finish. The lock up of the print hood can then be released after this problem solved. Please use manual c ...
-
PYLE Audio PP-7200L - page 16
Part 16 • Do not set any liquid or drinks such as coffee on the printer case. • Do not touch any metal part to avoid possible electrostatic damage. • Do not touch the areas around the print head and motor during or right after printing. It can be very hot . • Do not allow the cut receipt to slide back into the cutter during the operation. A ...
-
PYLE Audio PP-7200L - page 17
Part 17 SPECIFIC ATIONS PRINTER ITEM SPECIFICATION Printing method Thermal sensitive line dot method Effective printing width 64 mm Thermal head configuration 512 dots / line Printing speed 180 mm /sec. Paper feed method Friction auto - feed Paper load method Drop and use Auto - cutter capability Partial cut (1 point at center left) Manual cutter S ...
-
PYLE Audio PP-7200L - page 18
Part 18 SERVICE WINDOW SETUP PRINTER On bottom cover of the Aura series thermal printer, there is screwed a metal plate for setup window. In this window, there is a 8 position DIP switch for printer setup. Please use proper tool to change the switch setting when necessary. The switch position counting starts from the nearest edge of printer. The ON ...
-
PYLE Audio PP-7200L - page 19
Part 19 to host wheneve r an off line status occurs. Therefore, signals including the paper near end detect will generate busy signal to the host. Consequently, the printing may be stopped even when there is still a long way to go before the paper roll is actually exhausted. Taki ng the paper out beep into consideration, the printer will keep on be ...
-
PYLE Audio PP-7200L - page 20
Part 20 The Switch position 1 default set to ON . The print speed is fixed at 42.5 lines/sec. Switch position 2 is usually set to OFF for use with 80 mm paper width. When the printer is installed with the 58 mm paper guide adaptor for use with the paper roll of 58 mm width, the switch should be set to ON. Switch position 3 is usually set to OFF for ...
¿Tienes una pregunta acerca de PYLE Audio PP-7200L?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con PYLE Audio PP-7200L, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con PYLE Audio PP-7200L probablemente compartirá una forma de solucionarlo.