-
Philips RFX9200 - page 1
RFX9200 www.pronto.philips.com EN Installer’s Guide ...
-
Philips RFX9200 - page 2
Concept and realisation of the Guide: Human Interface Group, De Regenboog 11, 2800 Mechelen (Belgium) www.higroup.com RFX9200 Extender User Guide © Copyright 2007 Philips Innovative Applications N.V., Interleuvenlaan 74-76, 3001 Leuven (Belgium) Remark: All rights are reserved. Reproduction in whole or in part is prohibited without prior consent o ...
-
Philips RFX9200 - page 3
E N G L I S H 3 Contents Contents 1 How to Use the Extender 4 1.1 Introduction 4 1.2 Taking a Closer Look 6 2 How to Install the Extender 7 2.1 How to Configure the Extender 7 2.2 How to Connect the Extender 7 2.3 How to Position the Extender when Using the Front Blaster 7 2.4 How to Install the Single IR Emitters 9 3 How to Do More 10 3.1 How to ...
-
Philips RFX9200 - page 4
4 How to Use the Extender 1 How to Use the Extender 1.1 Introduction Infrared (IR) remote controls do not work properly when obstacles between the remote control and the audio/video devices disturb the operating signal. This problem can be solved using radio frequency (RF) as a carrier for IR commands. The Remote Control, in combination with the Ex ...
-
Philips RFX9200 - page 5
E N G L I S H 5 How to Use the Extender You can combine multiple extenders or combine the RFX9200 and the PCX9200 as shown in the situation above. You can control each Extender individually with one or more Remote Controls. ...
-
Philips RFX9200 - page 6
6 How to Use the Extender 1.1 Taking a Closer Look Power led Front blaster Busy led Channel switch Extender ID dial Power input 4 IR outputs 4 dipswitches for IR outputs ...
-
Philips RFX9200 - page 7
E N G L I S H 7 How to Install the Extender 2 How to Install the Extender Make sure you have the following components: Extender, power adapter, Single IR emitters and optionally screws. The installation of the Extender consists of 4 main steps : • Configuring the Extender; • Connecting the Extender; • Positioning the Extender; • Installing ...
-
Philips RFX9200 - page 8
8 How to Install the Extender Once you have found the best position, you can optionally mount the Extender onto a piece of furniture using screws. 1 Drive the screws into a rack, closet or another piece of furniture. Provide sufficient space to connect the power adapter and to slide the Extender in place. E Tip Depending on the surface, it may be ...
-
Philips RFX9200 - page 9
E N G L I S H 9 How to Install the Extender 2.4 How to Install the Single IR Emitters The Single IR emitters can be used in combination with, or as an alternative to the front blaster. Plug the Single IR emitters into the Extender. Attach the Single IR emitters to a neighboring surface facing the IR receiver (for aesthetic purposes or when it is di ...
-
Philips RFX9200 - page 10
10 How to Do More 3 How to Do More 3.1 How to Set the Extender IDs The Extender can be used in several situations: out of sight or inside a closet. Since the Extender ‘communicates’ with the Remote Control, you must set the same Extender ID (identity) on both appliances. The settings depend on whether you have a single Extender or multiple Exte ...
-
Philips RFX9200 - page 11
E N G L I S H 11 How to Do More 3.2 How to Do a Range Check If the Remote Control and the Extender are too far apart, the signal will be out of range. You can do a range check on the Remote Control. D Note If no Extender is defined in the Configuration Program, the Range Check Extenders option will not be presented in the Service Menu. 1 Press an ...
-
Philips RFX9200 - page 12
3.4 How to Adjust the Power Level of the IR Outputs At the back of the Extender, there are 4 dipswitches, one for each IR Output. Use these dipswitches to configure the power level of the Single IR emitters. • Raise the power levels if there is a device near that might cause IR interference such as a plasma TV. • Lower the power levels if you ...
-
Philips RFX9200 - page 13
5 Specifications The specifications and design of this product are subject to change without notice. E N G L I S H 13 Specifications Hardware Extender • 802.15.4 compliant RF technology • 2 LED indications for Power and Busy • Up to 16 extenders in a system • 4 addressable outputs for IR emitters • Positioning: freestanding or mounted ...
-
Philips RFX9200 - page 14
14 Approbation & safety content RFX9200a Approbation & safety content RFX9200 FCC Compliancy This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may caus ...
-
Philips RFX9200 - page 15
15 Approbation & safety content RFX9200 Regulations According to R&TTE Declaration of Conformity: Hereby, Philips Consumer Electronics, BL Home Control declares under his responsibility that the product RFX9200 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC Bulgarian С настояще ...
-
Philips RFX9200 - page 16
16 Approbation & safety content RFX9200 WEEE regulation (for EU only): Bulgarian Изхвърляне на старото ви изделие Вашето изделие е конструирано и произведено с висококачествени материали и компоненти, които могат да се рецик ...
-
Philips RFX9200 - page 17
17 Approbation & safety content RFX9200 Italian Smaltimento di vecchi prodotti Il prodotto è stato progettato e assemblato con materiali e componenti di alta qualità che possono essere riciclati e riutilizzati. Se su un prodotto si trova il simbolo di un bidone con ruote, ricoperto da una X, vuol dire che il prodotto soddisfa i requisiti dell ...
-
Philips RFX9200 - page 18
© Copyright 2007 Philips Innovative Applications N.V., Interleuvenlaan 74-76, 3001 Leuven (Belgium) 3104 205 3462.1 ...
¿Tienes una pregunta acerca de Philips RFX9200?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Philips RFX9200, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Philips RFX9200 probablemente compartirá una forma de solucionarlo.