-
Makita 2414DB - page 1
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com P or tab le Cut-Off MODEL 2414DB 003753 DOUBLE INSULA TION ...
-
Makita 2414DB - page 2
2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . For Y our Own Safety Read Instruction Man ual Bef ore Operating T ool Save it f or future refe rence GENERAL SAFETY PRECA UTIONS USA007-1 (F or All T ools ) 1. KNO W Y OUR PO WER TOOL. Read the ow ...
-
Makita 2414DB - page 3
3 11 . AL W A YS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty . Ever yda y eyeglasses only have impact resistant lenses, they are NO T safety glasses. 12. SECURE WORK. Use c lamps or a vise to hold work when practical. It’ s safer than using your hand and it frees both hands to operate tool. 13. DON’T O VERREA CH ...
-
Makita 2414DB - page 4
4 USE PROPER EXTENSION CORD . Make sure y our extension cord is in good condition. When using an e xtension cord, be sure to use one heavy enough to carr y the current y our product will draw . An undersized cord will cause a drop in line v oltage resulting in loss of power and o verheating. T able 1 shows the correct siz e to use depending on cord ...
-
Makita 2414DB - page 5
5 11 . Before using the tool on an actual w ork- piece, let it run for a while. Watc h for vibration or wobb ling that could indicate poor installation or a poorly balanced wheel. 12. W atch out for flying sparks when operat- ing. They can cause injury or ignite com- bustible materials. 13. Remove material debris fr om the area that might be ignite ...
-
Makita 2414DB - page 6
6 INST ALLA TION Securing cut-off This tool should be bolted with two bolts to a le vel and stab le surf ace using the bolt holes provided in the tool’ s base. This will help pre vent tipping and possible personal injury . FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checkin ...
-
Makita 2414DB - page 7
7 Stopper plate The stopper plate pre vents the cut-off wheel from contacting the workbench or floor . When a new wheel is installed, set the stopper plate to position (A). When the wheel wears down to the e xtent that the lower portion of the workpiece is left uncut, set the stopper plate to position (B) to allow increased cutting capacity with a ...
-
Makita 2414DB - page 8
8 ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is switched off and unplugged befo re carr ying out any work on the tool. Removing or installing cut-off wheel T o remove the wheel, r aise the safety guard. Press the shaft lock so that the wheel cannot re volv e and use the socke t wrench to loosen the he x bolt by turning it counterclockwis ...
-
Makita 2414DB - page 9
9 When the cut-off wheel has worn down considerab ly , use a spacer bloc k of sturdy , non-flammable material behind the workpiece as shown in the figure . Y ou can more efficiently utilize the worn wheel by using the mid point on the periphery of the wheel to cut the workpiece. When cutting workpieces ov er 65 mm (2-9/16 ” ) wide at an angle, at ...
-
Makita 2414DB - page 10
10 OPERA TION Hold the handle fir mly . Switch on the tool and w ait until the wheel attains full speed befo re lowering gently into the cut. When the wheel contacts the workpiece, gr adually bear down on the handle to perf or m the cut. When the cut is com- pleted, s witch off the tool and W AIT UNTIL THE WHEEL HAS COME T O A COMPLETE ST OP before ...
-
Makita 2414DB - page 11
11 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. Replacing carbon brushes Remov e and check the carbon brushes regularly . Replace when they we ar down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes ...
-
Makita 2414DB - page 12
Memo 12 ...
-
Makita 2414DB - page 13
13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut ...
-
Makita 2414DB - page 14
14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade ...
-
Makita 2414DB - page 15
15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair ...
-
Makita 2414DB - page 16
W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o ...
¿Tienes una pregunta acerca de Makita 2414DB?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 2414DB, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 2414DB probablemente compartirá una forma de solucionarlo.