-
Patton electronic 1092 - page 1
USER MANUAL MODEL 1092 High Speed, 2-Wire, Sync & Async Short Range Modem SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part# 07M1092-F Doc# 03301 1UF Revised 6/16/98 CERTIFIED An ISO-9001 Certified Company ...
-
Patton electronic 1092 - page 2
T ABLE OF CONTENTS Section Page 1.0 W arranty Information .............................................................2 1.1 Radio and TV Interference 1.2. CE Notice 1.3 Service Information 2.0 General Information ...............................................................4 2.1 Features 2.2 Description 3.0 Configuration ........................ ...
-
Patton electronic 1092 - page 3
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor . If any questions or problems arise during installation or use of this product, please do not hesitate to contact Patton Electronics T echnical Support at (301 ...
-
Patton electronic 1092 - page 4
3.0 CONFIGURA TION The Model 1092 is equipped with two sets of eight DIP switches, which allow configuration of the unit to a wide variety of applications. The Model 1092 is also equipped with an internal switch that allows selection of 1 15 or 230 V AC power inputs (Note: this switch is not present in Models 1092-UI and 1092-DC). This section desc ...
-
Patton electronic 1092 - page 5
Switches S1-4 and S1-5: Asynchronous/Sync Operation Use Switches S1-4 and S1-5 to configure the Model 1092 for async/sync operation. Both switches must be set in the “Off” position. There is no other valid setting. S1-4 S1-5 Setting Off Off Async/Sync On Off Reserved Off On Reserved On On Reserved Switches S1-6 and S1-7: System Clock Mode Use S ...
-
Patton electronic 1092 - page 6
3.2 CONFIGURING THE SOFTW ARE SWITCHES The Model 1092 features a menu-driven command system that allows you to configure either the local or remote 1092. Follow the instructions below to configure the Model 1092 using the software switches: 1) Connect the serial RS-232 port of a V100 or similar DTE with terminal emulation to the EIA/TIA-561l port o ...
-
Patton electronic 1092 - page 7
3.2.1 Configuring the Local 1092 T o configure the LOCAL 1092, make a selection from the following MAIN MENU screen. T o configure the REMOTE 1092, type [$] (Shift- 4) and refer to Section 3.2.2 . MAIN MENU Option 1: Display Active Configuration Select Option 1 to display the most recent configuration of the local Model 1092 (See below). The Model ...
-
Patton electronic 1092 - page 8
1. DTE Rate Select Option 1 in the SOFTW ARE CONFIGURA TION menu to select the async. or sync. DTE Rate of the Model 1092. Different DTE Rate menu screens will display for async. or sync. bit rates. The selections are shown below . a) This menu is displayed when the data format is synchronous: b) This menu is displayed when the data format is async ...
-
Patton electronic 1092 - page 9
MAIN MENU Option 5: Select Hardware/Software Control Select Option 5 from the MAIN MENU selects whether the Model 1092 will use the hardware switch settings or the software switch settings for its active configuration. If Options 1 or 2 are selected, the 1092RC will use the current hardware or software switch settings as the active configuration. A ...
-
Patton electronic 1092 - page 10
MAIN MENU Option 7: T est Modes Select Option 7 from the MAIN MENU to select the test mode status of the Model 1092. (below). The Model 1092 T est Mode settings help to verify the integrity of the data link and isolate communication difficulties. NOTE: An error counter is displayed when the unit is in one of the above test modes except LLB and RDL. ...
-
Patton electronic 1092 - page 11
3.2.2 Configuring the Remote 1092 T o configure the Remote 1092, make a selection from the following REMOTE UNIT CONFIGURA TION MAIN MENU. T o return to the LOCAL 1092 MAIN MENU screen, press [ESC] and refer to Section 3.2.1 . REMOTE MAIN MENU Option 1: Display Remote Unit Configuration Select Option 1 to display the configuration of various parame ...
-
Patton electronic 1092 - page 12
4.2 CONNECTION TO THE SERIAL PORT The serial port interface on the Model 1092 uses interchangeable QuikConnect™ Modules. Each QuikConnect™ Module has a 50-pin card edge connector on one side and a serial port interface on the other . Figure 4 below shows how a QuikConnect™ Module plugs into the back of the Model 1092. 4.2.1 Changing QuikConne ...
-
Patton electronic 1092 - page 13
Installing the New QuikConnect™ Module 1) Make sure the power switch is off. Leave the power cord plugged into a grounded outlet to keep the unit grounded. 2) Hold the module with the faceplate toward you and align the module with the guide slots in the rear panel of the Model 1092. 3) While keeping the module’ s faceplate parallel with the Mod ...
-
Patton electronic 1092 - page 14
4.3.2 Connecting to a DC Power Source The 48 VDC power supply option uses a 3-pin terminal block with spring-type connectors. Please refer to the Model 1090 Series Service Manual for further instructions. 25 5.0 OPERA TION Once the Model 1092 is properly configured and installed, it should operate transparently . This sections describes power-up, r ...
-
Patton electronic 1092 - page 15
NS Glow red to indicate that the local Model 1092 has not yet connected with the remote 5.3 TEST MODES The Model 1092 offers two proprietary loopback test modes, plus a built-in V .52 BER test pattern generator , to evaluate the condition of the modems and the communication link. These tests can be activated physically from the front panel, or via ...
-
Patton electronic 1092 - page 16
2. If the above test indicates no errors are present, move the V .52 toggle switch DOWN, activating the “51 1/E” test with errors present. If the test is working properly , the local modem's red “ER” LED will glow . A successful “51 1/E” test will confirm that the link is in place, and that the Model 1092’s built-in “51 1” ge ...
-
Patton electronic 1092 - page 17
APPENDIX B P A TTON MODEL 1092 F ACTOR Y REPLACEMENT P ARTS AND ACCESSORIES Patton Model # Description IM1/A ...............................V .24 with DB25F IM1/B ...............................RS422/RS530 with DB25F IM1/C ...............................V .35 with M34F IM1/D ...............................X.21 with DB15F IM1/E ..................... ...
-
Patton electronic 1092 - page 18
APPENDIX C P A TTON MODEL 1092 INTERF ACE PIN ASSIGNMENT (Continued) V .35 Interface (M/34F Female Connector) (DCE Configuration) Pin # Signal B ...........................SGND (Signal Ground) C ...........................R TS (Request to Send) D ...........................CTS (Clear to Send) E ...........................DSR (Data Set Ready) F..... ...
-
Patton electronic 1092 - page 19
APPENDIX D P A TTON MODEL 1092 Pin Out Control Port The 1092 control port is an 8 position connector , compliant with EIA/TIA-561. Pin Function RJ45 Pin No. Ground 4 Receive data (to DTE) 5 T ransmit data (from DTE) 6 35 Dear V alued Customer , Thank you for purchasing Patton Electronics products! W e do appreciate your business. I trust that you f ...
¿Tienes una pregunta acerca de Patton electronic 1092?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Patton electronic 1092, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Patton electronic 1092 probablemente compartirá una forma de solucionarlo.