-
Fujitsu fi-5900C - page 1
P3PC-1422-03EN ...
-
Fujitsu fi-5900C - page 2
...
-
Fujitsu fi-5900C - page 3
fi-5900C Image Scanner Getting Started i CONTENTS ■ Regulatory Informatio n .......................... .............................. ii ■ Note, Liability .................. ..................................................... iii ■ Safety Precautions .... .................................... ........................ v Chapter1 PREPARING THE ...
-
Fujitsu fi-5900C - page 4
ii INTRODUCTION Thank you for purchasing the fi-590 0C Duplex Color Scanner. This document describes h ow to use fi-5900C and basic operation methods. Before you start u sing fi-5900C be sure to thoroughly read this manual to ensure correct use. The "Operator’s Guide" stored on the Setup CD-ROM provides useful and detailed in formation ...
-
Fujitsu fi-5900C - page 5
fi-5900C Image Scanner Getting Started iii consumption. It is an open system in which business proprietors c an participate voluntarily . The targeted products are of fice equipment such as computers, monitors, printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and lo gos are unifor m among participating nations. ? ...
-
Fujitsu fi-5900C - page 6
iv Where there is no distinction between the different versions of the above operating system, the general term "W indows " is used. All the descriptions in this manual assume the usage of Adobe Acro bat bundled with this product. However , Adobe Acrobat may be upgraded without n otice. If the descriptions differ from the screens actually ...
-
Fujitsu fi-5900C - page 7
fi-5900C Image Scanner Getting Started v ■ Safety Precautions Do not damage the AC cable. Use only specified AC cables and connector cables Use this scanner only at the indicated power volt age. Do not connect to multiple- power strip s. Do not touch the AC cable with wet hands. Wipe any dust from the power plug. Do not inst all th e devi ce in l ...
-
Fujitsu fi-5900C - page 8
vi Do not install the scanner on unst able surfaces. Do not block the ventilation ports. Do not place heavy object s or st and on top of the scanner . Firmly insert the power plug. A void any contact when scanner is in use. Do not use the scanne r immediately after moving it from a cold place into a warm room. Before moving the scanner , disconnect ...
-
Fujitsu fi-5900C - page 9
fi-5900C Image Scanner Getting Started 1 Chapter1 PREP ARING THE SCANNER 1.1 Checking the Contents of the Scanner Package When you unpack the scann er package, make sure that the packa ge contains a ll the pa rts on the list included in the package . If any parts are missing or defective, contact your scan- ner dealer or an authorized FUJITSU scann ...
-
Fujitsu fi-5900C - page 10
2 ■ Removable Parts 1.3 Operator panel The operator panel is located on the right side of the scanner. The panel consists of a Function Number Dis- play, buttons and a LED. No. Name Descripti on 1 Document smoother Attached when the stacker posi- tion is set to align the ejected doc- ument by the l eading edge, or when scanning documents with dif ...
-
Fujitsu fi-5900C - page 11
fi-5900C Image Scanner Getting Started 3 ■ Indications on the Function Number Display The following shows the i ndicatio ns on the Functi on Number Display. HINT Operator Panel Overlays are available in French, German, Italian, Spanish, Chinese, Russian and Korean. To change the over- lay, open the plastic cover. nd t Thin Send to Scan No. Descri ...
-
Fujitsu fi-5900C - page 12
4 Chapter2 INST ALLA TION OF THE SCANNER 2.1 Installing the Scanner 1. Place the scanner at its installation site. For details on the scanner's dimensions and required installation space , refer to the fi-5900C Operator’s Guide, chapte r "10. Scanner Specifi- cations". 2. Connect the AC cable to the Power inlet of the scanner and p ...
-
Fujitsu fi-5900C - page 13
fi-5900C Image Scanner Getting Started 5 3. Press the "I" side of the main power switch to turn on the scanner. ■ Connecting the SCSI interface When using the scanner with a SCSI interface, the fol- lowing SCSI cable and SCSI card must be purchased. • SCSI cable: Use a SCSI cable whose connector on the scan- ner side is the 68-pin hi ...
-
Fujitsu fi-5900C - page 14
6 3. When using the SCSI cable, set the SCSI ID using the SCSI ID switch on t he back of the scanner. (Refer to step 3 in "Connecting the SCSI interface" on page 5.) 4. Press the "I" side of the main power switch to turn on the scanner. 2.3 Installing the Scanner Application For scanning documents with this scanner, both sc anne ...
-
Fujitsu fi-5900C - page 15
fi-5900C Image Scanner Getting Started 7 ASPI Manager V4.01 or later is required (th e generally comes with SCSI board prod ucts). ■ Installing the FUJITSU TWAIN32 Scanner Driver 1. Open the hopper. 2. Press the power button to turn the scanner ON. 3. Turn on your PC an d log on to Windows. ⇒ The scanner is automatically detected and a "We ...
-
Fujitsu fi-5900C - page 16
8 8. Image Processing Software Option installation windows appears. The Image Processing software is an optional software that provides advanced binarization image processing to the scanner dirver. 9. Select a language used for installation on [Choose Setup Language] window and click [OK]. 10. Install the TWAIN driver following the instruc- tions i ...
-
Fujitsu fi-5900C - page 17
fi-5900C Image Scanner Getting Started 9 ■ Confirming Installation 1. Load documents on the scanner. For details on how to set documents, refer to the "2.6 Loading Documents on the Hopper" in the fi- 5900C Operator’s Guide provided in the CD- ROM. 2. Start ScandAll21. Select [Start] - [Programs] - [Scanner Utility for Microsoft Window ...
-
Fujitsu fi-5900C - page 18
10 For FUJITSU ISIS Scanner Driver ■ Preparation Confirm the following items before installing the appli- cation. • Take out the Setup CD-ROM from its pack- age, but do not insert the Setup CD-ROM into the CD driver yet. • Connect the scanner correctly to you r PC. ■ Installing the FUJITSU ISIS Scanner Driver 1. Open the hopper. 2. Press th ...
-
Fujitsu fi-5900C - page 19
fi-5900C Image Scanner Getting Started 11 7. The Error Recovery Guide Installa tion window appears. The Error Recovery Guide is a software that dis- plays troubleshooting information on screen if any scanner error occurs . Although this soft- ware’s installation is hi ghly recommended, it can be installed later if you do not install it in this st ...
-
Fujitsu fi-5900C - page 20
12 4. Enter required information, then click [Next >]. 5. Install the application following the instructions in the window. ■ Confirming Installation 1. Load documents on the scanner. For details on loading do cuments, refer to "2.6 Loading Documents on the Hopper" in the fi- 5900C Operator's Guide on the S etup CD-ROM. 2. Start ...
-
Fujitsu fi-5900C - page 21
fi-5900C Image Scanner Getting Started 13 2. Click [INSTALL PRODUCTS] and then click [Error Recovery Guide]. 3. Select a language used for th e installation in the "Choose Setup Language" window and click [OK]. 4. Install the application following the in structions in the window. 5. When the [InstallShield Wizard Complete] win- dow appear ...
-
Fujitsu fi-5900C - page 22
14 5. Follow the instructions to install the software. ■ Uninstalling Supplied Programs Follow the procedure below to uninstall supplied pro- grams. 1. Start up your PC. 2. Exit all currently running progra ms. 3. Select [Control Panel] - [Add or remove Pro- grams] from the [Start] menu. ⇒ This displays the "Add or remove Programs" sc ...
-
Fujitsu fi-5900C - page 23
fi-5900C Image Scanner Getting Started 15 • When uninstalling Software Operatio n Panel, select " Software Operation Panel ". 5. Click the [Change/Remove] or [Remove] but- ton. 6. When the confirmation dialogbo x appears, Click the [OK] or [Yes] button. ⇒ This executes the uninstallation. ATTENTION When uninstalling Ad obe Acrobat, re ...
-
Fujitsu fi-5900C - page 24
AP- 1 Appendix 1 TROUBLESHOOTING ■ Troubleshooting checklist Symptom Check this item Remedy Scanner does not turn on. Have you pushed the power button on the front of the scanner? Push the power b utton. Have you pushed the main power switch at the back of the scanner? Push the Main power switch of the scanner. Then push the power button. Is the ...
-
Fujitsu fi-5900C - page 25
fi-5900C Image Scanner Getting Started AP- 2 Paper is not fed (pick error occurs frequen tly, or docu- ment stops midway). Do the documents satisfy the "Docu- ment Quality" and the "Multifeed Detec- tion Conditions" in the chapter 5 of the fi-5900C Operator’s Guide? Use the documents that satisfy the "Document Quality&quo ...
-
Fujitsu fi-5900C - page 26
AP- 3 ■ Temporary error The following shows the proced ure for releasing of each of the temporary errors. • "U1" error 1. Remove the jammed documents. (Refer to the fi-5900C Oper ator’s Guide "6.1 Clearing Document Jams" on the Setup CD- ROM.) 2. Confirm that the documents meet the paper specifications for scanning. (Refer ...
-
Fujitsu fi-5900C - page 27
fi-5900C Image Scanner Getting Started AP- 4 Appendix 2 DAIL Y CARE ■ Cleaning Materials For details about the cleaning materials, contact the FUJITSU scanner dealer where you purchas ed the scan- ner. ■ Cleaning Method The ADF must be cleaned with a lint-free cloth moist- ened with the Cleaner F1. The Feed roller must be cleaned with a lint-fr ...
-
Fujitsu fi-5900C - page 28
AP- 5 Appendix 3 REPLACING CONSUMABLES ■ Consumables and Replacement Cycle The followings are the specif ications of consumables and their recommended replacement cycles. To purchase consumables, contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. The replacement cycles above are rough guidelines w ...
-
Fujitsu fi-5900C - page 29
fi-5900C Image Scanner Getting Started AP- 6 ■ Pick roller ■ Separator roller ■ Brake roller Pick roller Separator roller Pad Cover Brake roller Cover ...
-
Fujitsu fi-5900C - page 30
z Copying of the contents of this manual in whole or in part and copying of the scanner applic ation is forbidden under the copyright la w. z The contents of this manual are subject to change without notice. z PFU LIMITED is not liable whatso ever for any damages resulting from use of this scanner and proc edures described in this manual, profit lo ...
¿Tienes una pregunta acerca de Fujitsu fi-5900C?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Fujitsu fi-5900C, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Fujitsu fi-5900C probablemente compartirá una forma de solucionarlo.