-
Texas Instruments SCAU020 - page 1
10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board User's Guide March 2007 Serial Link Products SCAU020 ...
-
Texas Instruments SCAU020 - page 2
2 SCAU020 – March 2007 Submit Documentation Feedback ...
-
Texas Instruments SCAU020 - page 3
Contents 1 General Description ..................................................................................................... 5 2 Signal Path and Control Circuitry .................................................................................. 6 3 Block Description .......................................................................... ...
-
Texas Instruments SCAU020 - page 4
List of Figures 1 CDCE421EVM Evaluation Board .......................................................................................... 5 2 CDCE421EVM Programming Blocks ...................................................................................... 6 3 Software Installation Screen ........................................................... ...
-
Texas Instruments SCAU020 - page 5
1 General Description User's Guide SCAU020 – March 2007 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board Figure 1. CDCE421EVM Evaluation Board Features: • Easy-to-use evaluation module generates low phase noise clocks between 10.9MHz—1175MHz • Simple device programming via host-powered USB port • Fast configuration through pr ...
-
Texas Instruments SCAU020 - page 6
www.ti.com 2 Signal Path and Control Circuitry Signal Path and Control Circuitry The CDCE421 can accept a 27MHz—38.33MHz frequency input from either an LVCMOS source (up to 3.3V) or a crystal in the same frequency range. The CDCE421EVM is divided into four blocks. The programming section and device power for each sector can be enabled or disabled ...
-
Texas Instruments SCAU020 - page 7
www.ti.com 3 Block Description 3.1 Block A 3.2 Block B 3.3 Block C 3.4 Block D 4 Software-Selectable Options Block Description This section discusses the four EVM blocks. Block A includes a CDCE421 QFN device that accepts an LVCMOS reference input through the vertical SMA input connector (Ref Input) which is ac-coupled onto the board. This block in ...
-
Texas Instruments SCAU020 - page 8
www.ti.com 5 Installing the Software GUI and USB Driver Installing the Software GUI and USB Driver The CDCE421EVM software can be installed on a PC running the Microsoft Windows ® 2000 operating system or higher (including Windows XP ® ). To start software installation, run the ChronosSetup.msi file (available on the CD shipped with the EVM). Fig ...
-
Texas Instruments SCAU020 - page 9
www.ti.com 6 ChronosGUI 6.1 Using Software-Enabled Automatic PLL Selection ChronosGUI After the setup wizard completes, start the GUI interface from the Start menu (Start → Texas Instruments → Chronos Eval → TIChronosGUI.exe). Connect the USB cable to the EVM. If Microsoft Windows prompts you for an appropriate driver, do not use the automati ...
-
Texas Instruments SCAU020 - page 10
www.ti.com ChronosGUI frequency should be entered here in this format: xx.xxx (specified in MHz). Step 3. Output Calculator and Apply PLL Settings. The second row of calculations is used to obtain the PLL settings necessary to achieve a particular output frequency provided a given input frequency to CDCE421. The input must be entered in the second ...
-
Texas Instruments SCAU020 - page 11
www.ti.com 6.2 Manual PLL Block Selection (Advanced Control) ChronosGUI The advanced control screen helps to set the PLL without having to manually alter the individual blocks within the PLL. If a user is familiar with PLL operation, one may activate individual control of the PLL blocks by clicking on the Advanced Control button, activating the win ...
-
Texas Instruments SCAU020 - page 12
www.ti.com ChronosGUI Table 1 lists the various menu items in this screen. Table 1. Software Settings Description Section Function VCO Select Selects between VCO1 and VCO2. Only one VCO can be used during operation. See CDCE421 data sheet for VCO tuning ranges. Prescalar The prescalar selection is determined in conjunction with VCO and output divid ...
-
Texas Instruments SCAU020 - page 13
www.ti.com 7 Configuring the Board 7.1 Programming and Testing Configuration (USB Cable Attached)—Default Configuration 7.2 Programming Configuration (USB Cable Attached) AUX Usingexternal 3.3Vsupply UsingonlyUSB powersupply 7.3 Testing Configuration from a Saved Configuration (with USB Cable Removed After Configuring the Board The ...
-
Texas Instruments SCAU020 - page 14
www.ti.com 8 Schematics and Layout Schematics and Layout Figure 9. CDCE421EVM Block Switch Off Figure 10 through Figure 14 show the printed circuit board (PCB) schematics. Note: Board layouts are not to scale. These figures are intended to show how the board is laid out; they are not intended to be used for manufacturing CDCE421EVM PCBs. 14 10.9MHz ...
-
Texas Instruments SCAU020 - page 15
www.ti.com Schematics and Layout Figure 10. CDCE421EVM Board Schematic SCAU020 – March 2007 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board 15 Submit Documentation Feedback ...
-
Texas Instruments SCAU020 - page 16
www.ti.com Schematics and Layout Figure 11. CDCE421EVM Board—Block A Schematic 16 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board SCAU020 – March 2007 Submit Documentation Feedback ...
-
Texas Instruments SCAU020 - page 17
www.ti.com Schematics and Layout Figure 12. CDCE421EVM Board—Block B Schematic SCAU020 – March 2007 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board 17 Submit Documentation Feedback ...
-
Texas Instruments SCAU020 - page 18
www.ti.com Schematics and Layout Figure 13. CDCE421EVM Board—Block C Schematic 18 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board SCAU020 – March 2007 Submit Documentation Feedback ...
-
Texas Instruments SCAU020 - page 19
www.ti.com Schematics and Layout Figure 14. CDCE421EVM Board—Block D Schematic SCAU020 – March 2007 10.9MHz–1175MHz Low Phase Noise Clock Evaluation Board 19 Submit Documentation Feedback ...
-
Texas Instruments SCAU020 - page 20
EVALUATION BOARD/KIT IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling th ...
-
Texas Instruments SCAU020 - page 21
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders ...
¿Tienes una pregunta acerca de Texas Instruments SCAU020?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Texas Instruments SCAU020, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Texas Instruments SCAU020 probablemente compartirá una forma de solucionarlo.