-
Haier QBJ1-150A58E - page 1
Instruction for use QBJ1-130A58E QBJ1-150A58E QBJ1-175A58E QBJ1-200A58E QBJ1-230A58E QBJ1-270A58E Please read this manual before usage Retain it for future reference Solar Water Heater ...
-
Haier QBJ1-150A58E - page 2
...
-
Haier QBJ1-150A58E - page 3
Content Features Before use Assembly Instruction Appearance and parts T echnical parameter 1 1 1 2 3 4 5 5 5 6 7 7 8 11 11 10 Precautions Notice T echnical data 4 The location Exterior and installation dimension T ank assembly Frame assembly Frame fastness Glass tube assembly Extraventricular plumbing instructions Indoor plumbing instructions Insta ...
-
Haier QBJ1-150A58E - page 4
Technical data 1 1. Inner cylinder: 2. Insulation: Polyurethane foam, thickness-45 mm, good heat preservation ef fect. 3. Outer shell: Aluminium / zinc coated steel sheet. 4. Frame: Steady structure, shapely and durable . SUS 304 stainless steel, food grade. Features Technical parameter Appearance and parts Models Specification of tubes Collector f ...
-
Haier QBJ1-150A58E - page 5
Precautions Precautions 1. 2. Avoiding irradiation without water after installation, it can't be used immediately , it should be sheltered. 3. When supplying water at the first time, it should be operated in the morning or evening or the condition of short of light; avoid supplying water in strong sunshine, in order to prevent vacuum tubes bom ...
-
Haier QBJ1-150A58E - page 6
Before use 3 Notice Please take time to read this manual and familiarize yourself with the function of this production. 1. Please check out the packing list. 2.If you fix electric auxiliary heating and controller , please select Haier equipped products. 3. T o avoid the scald, please mix the hot and the cold water before use it. 4. In order to prot ...
-
Haier QBJ1-150A58E - page 7
Assembly Instruction Notice: The solar water heater shall be installed by professional. Exterior and installation dimension: 4 Models Exterior dimension(mm) Installation dimension(mm) 1. Please install the solar water heater in the area that avoid the thunder. 2. Solar water heater angle range: east to south for 10 , west to south for 15 . 3. There ...
-
Haier QBJ1-150A58E - page 8
T ank assembly 1. Unpacking the tank, rip off the protection film. Uninstall the nut and cushion. 2. Place tank onto tank bracket cradle, inserting protruding bolts into holes. fasten with nuts. Notice: 1. Rip off the protection film after the installation to avoid the destroy of the tank, and please don't use the sharp tool. 2. Leave nuts loo ...
-
Haier QBJ1-150A58E - page 9
Assembly Instruction Glass tube assembly 1. Keep tubes out of the irradiation while assembling the unit or a scald may be caused. 2. Place the rounded side of rubber seal downwards on the open end of tubes.(A) 3. Insert the tube into base support of locating hole with gentle pressure and twisting motion. 4. Holding the tube, fix base support into b ...
-
Haier QBJ1-150A58E - page 10
Extraventricular plumbing instructions Assembly Instruction 7 Air supply pipe Over flow pipe Over flow hole ( conect to the room A Indoor plumbing instructions Inlet/outlet hole (1/2 ), conect to the room Air supply hole(1/2 ) forbidden to stem QBJ1-130A58E QBJ1-150A58E QBJ1-175A58E QBJ1-200A58E A b a Remarks: The permitted error limit of above par ...
-
Haier QBJ1-150A58E - page 11
1. Any alteration to the structure of the solar water heater may cause the trouble while using it. 2. There are 5 connection methods of the water pipe into the room, they are smoke way, vent-pipe hole on the wall appropriative solar well prepared cannula and the first three kinds are common. Before the installation, our professional will consult th ...
-
Haier QBJ1-150A58E - page 12
Assembly Instruction Pipelines thermal insulation notice 1.Outdoor pipelines should be thermal insulated according to local climate, bad thermal insulation may lead to heat loss. 2.The outlet used by electric tracing belt must ground reliably . The rated current of outlet is less than 10A, ensure is connected to plug reliably . 3.Fixing electric tr ...
-
Haier QBJ1-150A58E - page 13
10 Assembly Instruction Using Instruction 7.If the controller you choose has automatic water supply function, electromagnetic valve must be fixed in room horizontally; the direction of arrowhead labled on valve is the direction of water running out. Suggest fixing manual water supply side line, ensure that users can use water heater normally when t ...
-
Haier QBJ1-150A58E - page 14
Troubles treatment Phenomenon No water supply The temperature isn't high enough Possible reason The tank is empty The pipeline or the connection is impeded The evacuated tubes have damaged The water supply is paused or low water pressure The pipeline or the connection is Damaged Valve for water supply is unstuck or already damaged The evacuate ...
-
Haier QBJ1-150A58E - page 15
...
-
Haier QBJ1-150A58E - page 16
Rev. 01 Specific Number 0040500680F Made in China ...
¿Tienes una pregunta acerca de Haier QBJ1-150A58E?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Haier QBJ1-150A58E, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Haier QBJ1-150A58E probablemente compartirá una forma de solucionarlo.