-
Pelco 310 - page 1
INST ALLA TION C2496M-A (1/06) 310 Series Camclosure ® Integrated Camera System ...
-
Pelco 310 - page 2
...
-
Pelco 310 - page 3
C2496M-A (1/06) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Pelco 310 - page 4
4 C2496M-A (1/06) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other ...
-
Pelco 310 - page 5
C2496M-A (1/06) 5 REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC, Class A (black-white, EIA and CC ...
-
Pelco 310 - page 6
6 C2496M-A (1/06) Description The 310 Series Camclosure ® integrated camera system is a track-light design that mounts to a wall or ceiling. The system incorporates a camera and lens package into a small, unobstructive, medium- security enclosure designed for areas subject to vandalism. The system is quick and easy to install in a variety of indoo ...
-
Pelco 310 - page 7
C2496M-A (1/06) 7 • Mounting to ICS310-COND conduit adapter (not supplied) • Mounting to a two-gang electrical box CONDUIT ADAPTER W ALL OR CEILING TWO-GANG ELECTRICAL BOX W ALL OR CEILING ICS310-AP ADAPTER PLA TE (NOT SUPPLIED) 6-32 X 0.50 SECURITY SCREW (SUPPLIED WITH ADAPTER PLA TE) ...
-
Pelco 310 - page 8
8 C2496M-A (1/06) CONNECT VIDEO AND POWER 1. Some indoor installations do not require a heater. If the installation does not require a heater, disconnect the heater wiring. a. Remove the cover with the supplied 1/8-inch hollow screwdriver bit. b. Remove the camera from the mounting bracket, and unplug the four -pin heater connector in the base. The ...
-
Pelco 310 - page 9
C2496M-A (1/06) 9 ATTACH BASE Release the base locking ring for access to the mounting holes. T o attach the base to an adapter plate or conduit adapter, two 6-32 x 1.25-inch tamper-resistant screws are supplied with the adapters. Use the 1/8-inch hollow screwdriver bit supplied with the Camclosure. Mounting hardware for all other applications is n ...
-
Pelco 310 - page 10
10 C2496M-A (1/06) Adjustments (Color Camera Only) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however , adjustments may be necessary. 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit. 2. Adjust the vertical phase, iris level, focus, or switch settings (refer to proc ...
-
Pelco 310 - page 11
C2496M-A (1/06) 11 SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. For manually setting and locking the white balance, place a white background in front of camera and turn off switch 1. For gamma correction, switch to accurately reproduce scene b ...
-
Pelco 310 - page 12
12 C2496M-A (1/06) SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fi xed lighting conditions where there are no bright spots that darken other picture de ...
-
Pelco 310 - page 13
C2496M-A (1/06) 13 FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS T o adjust the focus, it may be necessary to remove the heater board in order to loosen the locking screw on the bottom of the lens. T o remove the heater board: 1. Disconnect the four-pin heater wiring. 2. Wait for the heater elements to cool if they are hot. 3. Press o ...
-
Pelco 310 - page 14
14 C2496M-A (1/06) Specifications General Pan/T ilt Adjustment Manual; 180° pan; 180° tilt Construction Aluminum base and cover , steel camera mounting bracket Finish Gray polyester powder coat Environment Low temperature, indoor/outdoor Operating T emperature -50° to 122°F (-46° to 50°C); de-ices to -10°F (-23°C) Heater T urns on at 50°F ...
-
Pelco 310 - page 15
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series p ...
-
Pelco 310 - page 16
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...
¿Tienes una pregunta acerca de Pelco 310?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Pelco 310, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Pelco 310 probablemente compartirá una forma de solucionarlo.